Sauder New Grange 421003 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-14
Français pg 15-16
Español pg 17-18
Lot # 500147 05/01/17
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Queen Headboard
New Grange Collection | Model 421003
How else are you
gonna know which
end is up?

Table of Contents Assembly Tools Required
3
4
5-14
15-16
17-18
19
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
421003 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
421003www.sauder.com/services Page 3
A
B
C
E
D
F
G
H
G
B
B
F
F
F
F
A TOP (1)
B BACK PANEL (3)
C LEFT LEG (1)
D VALANCE (1)
E TOP MOLDING (1)
F BACK PANEL MOLDING (5)
G ACCENT MOLDING (2)
H RIGHT LEG (1)

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
421003 www.sauder.com/servicesPage 4
HIDDEN CAM - 6
1F CAM SCREW - 6 8F BUSHING
CONNECTOR - 8
32F
BUMPER - 4
2M WASHER - 4
13M NUT - 4
24M
BLACK 1-7/8" FLAT HEAD SCREW - 6
2S
SILVER 3/4" MACHINE SCREW - 8
20S BROWN 1-5/8" FLAT HEAD SCREW - 6 55S
BLACK 2-3/8" FLAT HEAD BOLT - 4
103S
BLACK 1-1/4" FLAT HEAD SCREW - 27
7S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn six CAM SCREWS (8F) into the exact holes shown in
the VALANCE (D).
å Push six HIDDEN CAMS (1F) into the BACK PANELS (B).
421003www.sauder.com/services Page 5
8F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
1F (6 used)
(6 used)
B
D
B
B
Flat edge
Finished surface
Meet Part (B). This component has been
engineered to be lighter, stronger, faster…
well ok. Not technically faster. But
definitely makes for a sturdier Queen
Headboard that’s easier to assemble and
friendlier to the environment. A tracking label will be on this
surface of one of the BACK
PANELS. Please do not remove.

Step 2
å Fasten the TOP (A) to the VALANCE (D). Use six BROWN
1-5/8" FLAT HEAD SCREWS (55S).
å NOTE: Do not overtighten the SCREWS into the TOP.
421003 www.sauder.com/servicesPage 6
BROWN 1-5/8" FLAT HEAD SCREW
(6 used in this step)
55S
Surface with holes
DFlat edge
Surface with CAM SCREWS
Long finished edge
A
Some assembly
(and snacks) required.

Step 3
421003www.sauder.com/services Page 7
å Insert eight BUSHING CONNECTORS (32F) into the holes
in the ACCENT MOLDINGS (G).
å NOTE: Be sure to insert the BUSHING CONNECTORS
exactly as shown.
å Fasten the LEGS (C and H) to the ACCENT MOLDINGS (G).
Use eight SILVER 3/4" MACHINE SCREWS (20S) through
the LEGS, through the BUSHING CONNECTORS, and into
the ACCENT MOLDINGS.
C
G
(8 used)
32F
Surface with holes
H
G
Surface with holes
These holes
must be here.
The small holes are
closer to this edge.
The small holes are
closer to this edge.
SILVER 3/4" MACHINE SCREW
(8 used in this step)
20S

Step 4
421003 www.sauder.com/servicesPage 8
å Fasten one of the BACK PANELS (B) to three of the BACK
PANEL MOLDINGS (F). Use nine BLACK 1-1/4" FLAT
HEAD SCREWS (7S).
å NOTE: Use the exact holes shown.
å NOTE: Once the BACK PANEL MOLDINGS are fastened
to the BACK PANEL, the two outer MOLDINGS will
overhang the BACK PANEL.
Surface with
HIDDEN CAMS
B
F
F
F
Edge with HIDDEN CAMS
Use the holes
closer to this edge.
These holes are
closer to this edge.
BLACK 1-1/4" FLAT HEAD SCREW
(9 used in this step)
7S

Step 5
421003www.sauder.com/services Page 9
å Fasten the remaining two BACK PANELS (B) to the
remaining two BACK PANEL MOLDINGS (F). Use six
BLACK 1-1/4" FLAT HEAD SCREWS (7S).
å NOTE: Use the exact holes shown.
These holes
are closer to
this edge.
Surface
with
HIDDEN
CAMS
B
Surface
with
HIDDEN
CAMS
B
Use the holes
closer to this edge.
Use the holes
closer to this edge.
These holes
are closer to
this edge.
Edge with
HIDDEN CAMS
Edge with
HIDDEN CAMS
F
F
BLACK 1-1/4" FLAT HEAD SCREW
(6 used in this step)
7S

Step 6
421003 www.sauder.com/servicesPage 10
å Fasten the two outer BACK PANELS (B) to the BACK
PANEL MOLDINGS (F) on the center BACK PANEL (B).
Use six BLACK 1-1/4" FLAT HEAD SCREWS (7S).
B
B
Outer BACK PANEL
with one BACK
PANEL MOLDING on
the other surface.
B
F
F
Outer BACK PANEL
with one BACK
PANEL MOLDING on
the other surface.
Center BACK PANEL
with three BACK
PANEL MOLDINGS
on the other surface.
Edge with
HIDDEN CAMS
If you're doing this to
help a friend, don't
leave without a bite.
BLACK 1-1/4" FLAT HEAD SCREW
(6 used in this step)
7S