Sauder Via 419717 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Knick-knack
paddywhack,
give your stu a home.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-19
Français pg 20-22
Español pg 23-25
Lot # 376718 10/09/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Hutch
Via Collection | Model 419717

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-19
20-22
23-25
26
27
419717 www.sauder.com/servicesPage 2
Electric drill with 1/4" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D UPPER SHELF (1)
E LOWER SHELF (1)
F UPPER BACK (1)
G LOWER BACK (1)
H LARGE UPRIGHT (2)
I SMALL UPRIGHT (3)
J CENTER UPRIGHT (1)
K RIGHT DOOR (2)
L LEFT DOOR (2)
M VALANCE (1)
N BULLETIN BOARD (1)
A
B
C
DE
F
G
H
H
J
K
K
L
L
M
N
I
419717www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
FELT DISC CARD - 1
1M
GOLD 1" MACHINE SCREW - 8
50S
BLACK 9/16" LARGE HEAD SCREW - 10
1S
ANGLE BRACKET - 5
5G
BROWN 7/16" LARGE HEAD SCREW - 8
6S
BLACK 1-7/8" FLAT HEAD SCREW - 15
2S
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S
TOUCH-UP PEN - 1
10M
7F TWIST-LOCK®FASTENER - 14 13F MINI TWIST-LOCK®
FASTENER - 16
61P TWIST-LOCK®
FASTENER COVER - 14 62P MINI TWIST-LOCK® COVER - 12 METAL PIN - 10
1R
PULL - 4
12K
BLACK 1/2" FLAT HEAD SCREW - 16
11S
HINGE - 4
53H
419717 www.sauder.com/servicesPage 4
CORD COVER - 4
66P
BULLETIN BOARD
BRACKET - 8
63G
RAISED HINGE - 4
31H
Raised
area

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the LOWER SHELF (E). Repeat
this for the ENDS (A and B) and UPRIGHTS (H and J).
å Push a SAUDER MINI TWIST-LOCK® FASTENER (13F) into the indicated holes in the BACKS (F and G).
419717www.sauder.com/services Page 5
13F
13F
13F
(14 used)
(16 used)
7F
F
G
7F
E

å Fasten the UPPER BACK (F) to the TOP (C). Tighten
four MINI TWIST-LOCK® FASTENERS.
Step 2
419717 www.sauder.com/servicesPage 6
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
Surface with MINI TWIST-LOCK® FASTENERS
Surface with holes
C
F

å Fasten the UPRIGHTS (H and J) to the TOP (C). Tighten
six TWIST-LOCK® FASTENERS.
å Fasten the UPPER SHELF (D) to the UPRIGHTS (H and J).
Use six BLACK 1-7/8" LARGE HEAD SCREWS (2S).
Step 3
419717www.sauder.com/services Page 7
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
C
H
H
J
BLACK 1-7/8" FLAT HEAD SCREW
(6 used in this step)
2S
D
Finished edge
Surface with more holes
Just think. The sooner
you do this, the sooner
you do something else.

å Insert six METAL PINS (1R) into the SMALL UPRIGHTS (I).
å Insert the METAL PINS (1R) in one end of the SMALL
UPRIGHTS (I) into the holes in the UPPER SHELF (D).
Step 4
419717 www.sauder.com/servicesPage 8
1R
Finished edge
I
I
I
D

å Fasten the LOWER SHELF (E) to the SMALL UPRIGHTS (I).
Use nine BLACK 1-7/8" LARGE HEAD SCREWS (2S).
å Fasten the LOWER BACK (G) to the LOWER SHELF (E).
Tighten four MINI TWIST-LOCK® FASTENERS.
Step 5
419717www.sauder.com/services Page 9
I
I
I
E
G
BLACK 1-7/8" FLAT HEAD SCREW
(9 used in this step)
2S
Surface with
TWIST-LOCK®
FASTENERS
Surface with MINI TWIST-LOCK® FASTENERS

å Insert four METAL PINS (1R) into the ENDS (A and B).
å Fasten the ENDS (A and B) to the TOP (C), UPPER SHELF (D),
LOWER SHELF (E), UPPER BACK (F), and LOWER BACK (G).
Tighten eight TWIST-LOCK® FASTENERS and eight MINI
TWIST-LOCK® FASTENERS.
å NOTE: Be sure the PINS in the ENDS insert into the holes
in the UPPER SHELF (D).
Step 6
419717 www.sauder.com/servicesPage 10
E
G
D
C
1R
1R
Surface
with holes
Surface
without
holes
Side Step: Make
nachos. (Optional, but
recommended.)
A
B
F