Schlage Encode SMART WIFI LEVER User manual

Quick Start Guide
SMART WIFI LEVERSMART WIFI LEVER

Backup
Key
Touchscreen
Assembly
Battery
Cover
Inside
Assembly
Backplate
Strike
Inside Assembly
Screws
Backplate
Screws
Latch/Strike
Screws
Parts
Latch
1 2 3
4 5
Pin wrench
*just in case you need
to remove levers.

Setting up your lock with your
smartphone?
Start with the Schlage Home app for guided
installation, set up, and pairing.
Not ready to start with the app?
You can access step-by-step interactive instructions
and user guide
information at:
No Internet? No problem.
Follow this Quick Start Guide to install your lock.
1
2
3
Before you begin
alle.co/EncodeLever

Communication Icon
•Flashes when lock is connecting
to WiFi to check for updates.
Low Battery Icon
•Flashes after code is entered
when battery is low.
•Solid when battery is critical.
The lock will not work without
new batteries.
Programming and Input
LED
•Amber when using manual
programming mode.
Home Button and
Checkmark Icon
•Turns on keypad backlight.
•Checkmark ashes when
code entry is correct.
Lock Button and “X” Icon
•Locks the lock.
•“X” ashes for a wrong user
code.
Touchscreen

1
step
Remove existing lever or knob.
Remove the entire lever, including the latch. You
may also want to remove the strike. Check with your
specic lever or knob manufacturer if you need help.
Tools
Don’t use a power drill!
Phillips screwdriver
1 2 3
4 5

2
step Install the latch.
You may need to change
your faceplate to t the hole
in the edge of your door.
The bevel on the latch
should face the door jamb.
1. Remove the faceplate by
inserting a screwdriver into
the notch and turning.
Rounded corner
No change needed.
Square
corner
No mortise
cut out
OR
Bevel
Jamb

Need Help?
Visit alle.co/EncodeLever.
2. Press square corner faceplate rmly on latch,
then install.
2. Turn to remove piece as shown, then press
circular faceplate on latch.
Piece of wood
3. Hammer latch into door
edge using a piece of wood
to protect the latch.
Actual Size

Install the strike into the door frame.
3
step
Actual Size

4
step
Install the touchscreen.
Route the cable through the door ABOVE the latch. Push the
touchscreen onto the door.

5
step
Install the backplate.
Route the cable over the latch and through the hole on the
backplate. Secure the backplate with screws. Make sure the outside
touchscreen is straight before tightening screws all the way.
Route wire
through hole
Actual Size
Don’t use a power drill!
You may damage your lock!
Phillips screwdriver
1 2 3
4 5

6
step
Connect the cable.
Tuck the cable and connector in the space as shown.
Phillips screwdriver

Secure the inside assembly to the door.
7
step
Don’t use a power drill!
You may damage your lock!
Phillips screwdriver
1 2 3
4 5
Remove battery cover to see the holes for the screws.
Actual Size

Phillips screwdriver
Install batteries and slide the cover on.
8
step
Pull out battery
holder. Install
batteries.
Reinstall battery holder.
Turn the battery holder
around so the batteries
face the door.

Levers should not block the door from closing. Levers
are interchangeable. Install levers to what you feel
looks best on your door.
Install levers.
Install inside lever.
Press until lever is secure. The
inside lever does not have a
key cylinder.
9
step
If you’re having trouble installing the cylinder,
or if your levers block the door, go to
alle.co/EncodeLever

After installation rotate key 90 counter clockwise to
remove, and put it in a safe place.
1. Insert cylinder into
lever.
Follow the steps below to install the outside
lever and key cylinder.
90 90
Lever end is
to the LEFT. Lever end is to the RIGHT.
OR
2. Insert key into cylinder. Cylinder
will be held in the lever by the key.
3. Rotate the key according
to the diagram below.
4. Press the lever with rotated
key onto the lever post
until it clicks into place.

Test your lock
1. Open your door!
2. Press the lock button
(on the inside of the door).
3. Find User Code A on the label on the
back of this Quick Start Guide.
4. Enter User Code A (four digits) into
the touchscreen keypad. + beep
5. Rotate then release the lever.
Did the latch retract and then extend?
10
step
If your lock isn’t
working, see
alle.co/EncodeLever
Need Help?
Yes. Lock is installed
correctly.
No. Latch retracted but did not extend
(latch is stuck). See step 2 and ensure
latch is moving freely.
No. Nothing happened. First check
step 8to ensure the batteries are
installed rmly and correctly. If the
problem persists, check step 6.

Now that your lock is
installed
you can access manual programming
instructions and factory default reset (FDR) steps
in the online interactive instructions.
alle.co/EncodeLever

How to use
your lock
LOCK
• Tap the lock button on
the outside touchscreen.
UNLOCK
• Enter a valid user code.
If you have an auto-relock
time set in the Schlage
Home app, it will auto-
lock. You can disable this
setting in the app.
Want to lock/unlock from anywhere
or add optional voice control?
Explore compatible smart home
systems at alle.co/EncodeLever

Pressing this button LOCKS the door.
Pressing this button UNLOCKS the door.
Your door will stay unlocked (even if auto-relock
is enabled) until:
• You press the inside lock button.
• You press the lock button on the
outside touchscreen.
• You lock the door using a smart
home system app.

© Allegion 2022
Printed in U.S.A.
47376548 Rev. 04/22-c
*47376548*
47376548
PLACE LABEL
HERE
These are your backup codes.
You will need these codes if you
ever factory default reset your lock.
Keep these safe!
Questions about your new
Smart WiFi Lever?
Please don’t return it to the store!
Let us help you rst!
alle.co/EncodeLever