SEA USER 1 - 24v DG R1 User manual

USER 1 - 24V DG MAXI
SEA S.p.A.
Zona Ind.le S. Atto - 64020 S. Nicolò a Tordino (TE)
Tel. [phone] - Fax [phone]
www.seateam.com
e-mail: [email protected]
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
67411261
23024074
REV. 02 - 01/2017
English
24V ELECTRONIC CONTROL UNIT FOR SLIDING GATES AND BARRIERS

26
DESCRIPTION OF THE COMPONENTS
CN1 = Input/Output connector
CN2 = Pre-wired limit switch connector
CN3 = Not Pre-wired limit switch connector
CN4 connector= Master/slave
CN5 = Courtesy light output connector
CN6 otors connector= M
CN7 = Batteries connector - Quick connection
CN8 = Power connector
CN9 = Jolly 3 connector
CNA = RX Receiver connector
CNE = Encoder connector
CNP = Programming connector
CNS = RF FIX receiver connector
EXP = External module connector
OK = Programming button
DOWN = Programming button
UP = Programming button
RL1 = Motors control relay
Rl2 = Motors control relay
RL3 = Light/dry output contact relay
PR1 = Rectifier bridge
F1 = Fuse 20 AT
Jp1 = Relay 3 activation
JP2 = Light/dry contact selection
TECHNICAL SPECIFICATIONS
Control unit power supply: 24 V~
Absorption in stand by: 30 mA
Maximum motor current: 20A
Environment temperature: -20°C +50°C
Specifications of external enclosure: 305 x 225 x 125 mm - Ip55
156 mm
100 mm
RX RECEIVER
JOLLY3
CN8 F1
CNA
CN9
CN5
CNP
RL1
CN4
UP DOWN OK
PR1
DISPLAY
EXP
POWER FUSE MOTOR LIGHT
MASTER/SLAVE
PROG
RADIO MODULE
JOLLY
CNE
ENCODER
1
CN7
RL2
CNS
CNS CN2
CN3
LIMIT SWITCH
- S +
RL3
JP2
JP1
CN1
CN6
English

27
CONNECTIONS
JUMPERS
The herein reported functions are available starting from revision 01.23 compatible
only with Jolly 3.
123 4 5 6 7 8 910 11 12 13
CN1
Start
Stop
Common
Antenna
START Ped.
Common
Photocell 1
Common
ANT COM START
PEDST
STOP COM PH1 PH2
EDGE AUX
COM 24V (FL)-
24V 750 mA max
(Accessori)
Safety edge
Flash (-)
Photocell 2
+ +
- -
123 4 5 6 7 8 910 11 12 13
CN1
ANT COM START
PEDST
STOP COM PH1 PH2
EDGE AUX
COM 24V (FL)-
Start
Stop
Common
Antenna
START Ped.
Common
Photocell 1
Common
24V 750 mA max
(Accessori)
Safety edge
Flash (-)
Photocell 2
+ +
- -
Optional
WARNING: The control unit is designed with the automatic detection of not used N.C. inputs (photocells, Stop and Limit switch) except the
SAFETY EDGE input. The exclude inputs in self-programming can be restored in the “Check inputs” menu without need to repeat the
programming (pag.37).
Limit switch Cl.1 (Yellow)
Limit switch Cl.1 (Yellow)
24V (Red)
Common (White)
Limit switch Op.1 (Green)
Limit switch Op.1 (Green)
MOTOR (CN6)
Max 400W
ENCODER (CNE)
1
Brown
White
Green
AUX Programmable
(24V 300 mA max)
AUX Programmable
(24V 300 mA max)
1
LIMIT SWITCH
CN2
CN3
LIGHT (CN5)
Light/Dry contact
M
LIGHT (CN5)
Max 100mA
POWER (CN8)
24V~
RL3
JP2
JP1
English

28
QUICK SELF-EARNING
PROGRAMMING
Start quick programming
You can start the quick programming by
holding UP for 5 s in the “Input check
menu", until the motor starts.
“Input check
menu"
Fast self-learning START command by
radio control
You can store the START button of the
remote control while pressing DOWN for 5 s
in the “Input check menu".
Once the writing "Press button" appears,
press the button of the transmitter, which
you want to store for the START command.
By pressing OK, you can exit the menu,
otherwise it will be left automatically after 5
seconds.
DISPLAY
UP DOWN
5 s 5 s
---
--
---
UP DOWN
English

29
UPDOWN
ALL OTHER PARAMETERS HAVE DEFAULT SETTINGS WHICH ARE USEFUL FOR THE 90% OF THE APPLICATIONS
BUT CAN BE HOWEVER SET THROUGH THE SPECIAL MENU. FOR ENTERING INTO THE SPECIAL MENU MOVE
ON ONE OF THE MENU AND PRESS THE UP AND DOWN BUTTONS AT THE SAME TIME FOR 5 S.
PROGRAMMING
QUICK START
MENU
SEA
SET MENU
SEA
SET MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
OK
2
3
5
6
7
8
9
OK
OK OK
OK OK
OK OK
OK OK
OK OK
OK OK
UP
UP
UP
UP
UP
UP
UP
PRESS
BUTTON STORED
TRANSMITTERS
START
MOTOR
REVERSE
MOTOR
LOGIC
PAUSE TIME
START IN
PAUSE
PROGRAM-
MING
TEST START
10
Skip this step if you do not want to program a transmitter
Press the
button of the
TX to be
stored
OK to exit
Menu or press
the button of
the next TX to
be stored
OKOK Choose the type of
motor with
UP or DOWN
To confirm and return
to main menu
Choose "ON" with UP or
DOWN button only if in
programming the motor starts
in opening
With UP or DOWN
choose
the desired logic
To confirm and return
to main menu
With UP or DOWN
choose a delay for
automatic closing
To confirm and return
to main menu
Skip this step
if you wna tto work
in half-automatic
logic
With UP or DOWN
Choose ON
To confirm and return
to main menu
With UP or DOWN choose ON
to start times learning
At the end of the selflearning
the control unit returns automatically
to the main menu
With
UP or DOWN Choose
ON to start test
To confirm and return to
main menu
Skip this step if a TX has already been stored
1
MENU
SEA
SET MENU
SEA
SET
OK
UP
LANGUAGE ITALIANO
UP
MENU
SEA
SET
(See
page 30)
(See
page30)
If the motor has
magnetic limit switches,
select "Magnetic"
in the special menu:
104 - SELECT LIMIT SWITCH
RECEIVER
MISSING
If on the display
appears the item:
Check if a receiver has
been connceted
(see page 26)
The gate will execute a CLOSING-OPENING-CLOSING CYCLE
UP
MENU
SEA
SET
OK
END
15
MENU
SEA
SET
OK
SPECIAL
MENU
16
UP
Press OK to return to the
display of the inputs state.
Press OK to enter the special menu.
PROGRAMMING
BUTTONS
OK
DOWNUP
To confirm and return
to main menu
Return to the
9-PROGRAMMING menu,
put the gate halfway and
repeat the times programming.
English

30
MENU Default
SET
MENU FUNCTIONS TABLE USER1 24V DG MAXI
Description Set value
Stop
Start Start
Stop
Unloch Storing of a command for
unlocking an electric brake
Italian
English
French
Spanish
2 - TRANSMITTERS
External module
Pedestrian Start
Clear memory
Delete A TX
External module
Pedestrian Start
Delete single transmitter
Delete transmitter memory
Olandese
1 - LANGUAGE
Español
English
Français
Italiano
Dutch
Italiano
Start
Pedestrian
Start
8 - START IN PAUSE
6 - LOGIC
Automatic
Open-stop-close-stop-open
2 buttons
Safety
Dead man
Open-stop-close-open
Automatic
Step by step type 1
Step by step type 2
Two buttons
Safety
Dead man
7 - PAUSE TIME Setting from 1s to 4min.
OFF
(semi-automatic logics)
In pause start is not acceped
In pause start is accepted
(See page 31)
1 240
Off
Off
On
Off
Off
5 - REVERSE MOTOR Off
On
Synchronized right motor
Synchronized left motor Off
9 - PROGRAMMING
10 - TEST START
15 - END
Start command
Times learning start
(See page 31)
Off On
Off On
Off
Off
Press OK to return to the display of the firmware version and to the one of inputs state.
16 - SPECIAL MENU Press OK to enter the special menu.
Open-stop-
close-open
End “Transmitters” menu output
Joint Joint
3 - MOTOR
Saturn fast-
Saturn
super fast
Saturn Fast - Saturn Super Fast
Saturn Fast - Saturn Super Fast
Hydraulic unit Hydraulic unit
Lepus box chain Lepus box chain
Saturn 1500 - Lepus 2000
Saturn 1500 - Lepus 2000
B-800
Slim
Without limitswitch, obligatory
mechanical stop in opening
and closing, obligatory Stop
on engine release
Without limitswitch, obligatory
mechanical stop in opening
and closing, obligatory Stop
on engine release
English

31
WORKING TIMES SELF LEARNING
Fig. 1 Fig. 2 Fig. 3
Fig.4
The control unit is pre-set with the default settings, to start the control unit with the DEFAULT settings just keep
pressed the UP and DOWN buttons at the same time power supplying the control unit the display shows the
message “Init”.
The DEFAULT settings are shown in the Menues table.
NOTE: When using a magnetic limit switches in general; make sure that the control unit is set on magnetic limit switch before
learning.
MENU 104 - SELECT LIMIT SWITCH - “Magnetic”
1) Disconnect the power supply, release the motor (Fig. 1) and manually position the leaves or the beam on halfway (Fig. 3-4).
2) Reset the mechanical lock (Fig. 2)
3) Select 9 - PROGRAMMING on the display, press OK and than one of the UP or DOWN buttons. Now the gate will automatically execute a
closing, opening and reclosing cylce.
Note: If the motor starts in opening, remove and re-put power supply, select on the display 5 - REVERSE MOTOR. And through the UP and
DOWN button put it on ON, or if you have the Jolly 3 programmer, activate the motor and limit switch exchange function. If the motor starts in
closing and stops, remove the power supply and reverse the motor cables, then repeat the programming procedure.
4)The self-learning is done.
ATTENTION: This procedure is potentially dangerous and should only be performed by qualified personnel in safety conditions.
FUNCTION LOGIC
AUTOMATIC LOGIC
A start impulse opens the gate. A second impluse during the opening will not be accepted.
A start impulse during closing reverses the movement.
SECURITY LOGIC
A start impulse opens the gate. A second impulse during opening reverses the movement.
A start impulse during closing reverses the movement.
STEP BY STEP TYPE 1 LOGIC
The start impulse follows the OPEN-STOP-CLOSE-STOP-OPEN logic.
STEP BY STEP TYPE 2 LOGIC
The start impulse follows the OPEN-STOP-CLOSE -OPEN logic.
NOTE1 : To have the automatic closing in this logic it is necessary to set a pause time , otherwise all the logics will be
semi-automatic
NOTE2: It is possible to choose whether to accept or not the start in pause, by selecting in the MENU point 8-START IN
PAUSE and choosing ON or OFF. The default parameter is OFF.
DEAD MAN LOGIC
The gate opens as long as the START button of opening is pressed; releasing it the gate stops. The gate closes as long as the
button connected to the PEDESTRIAN START is pressed; releasing it the gate stops. To execute complete opening and/or
closing cycles the related pushbuttons must be constantly pressed.
2 PUSH BUTTONS LOGIC
One start opens, one pedestrian start closes. In opening the closing will not be accepted. In closing a start command reopens, a
pedestrian start command (closes) will be ignored.
The SLIM motor has no limit switches and works only with Encoder. For the stroke learning it is necessary that the motor reaches the
mechanical stops. Learning provides a CLOSE-OPEN-CLOSE cycle with automatic detection of the mechanical stops. During normal cycle
the motor will stop at about 1 cm from the mechanical stop. This space will be regulated through the motor release parameter (meu 82).
Attention:
In case of the STOP command, power failure or obstacle detection, the motor will perform a closing maneuver at low speed up to the
mechanical stop in closing, to retrieve the position.
PROGRAMMING SLIM MOTOR WITHOUT LIMIT SWITCH
English

32
PRESS AT THE SAME TIME FOR 5 SECONDS TO ENTER OR TO EXIT THE SPECIAL MENU
MENU SP Default
SET
SPECIAL MENU FUNCTIONS TABLE USER 1 24V DG MAXI
For entering into the special menu move on one of the menu and press the UP and DOWN
buttons at the same time for 5 s. For exiting the special menu press END or move on one of the
menu and press the UP and DOWN buttons at the same time for 5 s.
Description Set Value
SPECIAL MENU
UPDOWN
30 100
17 - OPENING SPEED 1 *
18 - CLOSING SPEED 1 * 30 100
Setting from 30 to 100
Setting from 30 to 100
21 - OPENING SLOWDOWN
SPEED 1 *
22 - CLOSING SLOWDOWN
SPEED 1 *
30 100
30 100
Setting from 30 to 100
Setting from 30 to 100
25 - LEARNING SPEED * 30 100 Setting from 30 to 100
28 - OPENING TORQ 1 *
29 - CLOSING TORQ 1 *
10 100
10 100
On
xxx.
Encoder impulses during operation.
This parameter is useful for seeing if the
Encoder is working correctly.
Encoder impulses stored in programming
In ON enables the Encoder
32 - ENCODER *
xxx.
48 - ENCODER TOT. *
47 - ENCODER PAR. *
Off
32 - ENCODER *
In OFF disabled the Encoder
Off
33 - OPENING SENSITIVITY
MOTOR1 *
34 - CLOSING SENSITIVITY
MOTOR1 *
Disabled
Adjusts the intervention time
of the Encoder in opening
Off (Intervention excluded)
10% (Fast intervention)
99% (Slow intervention)
Disabled
Off (Intervention excluded)
10% (Fast intervention)
99% (Slow intervention) Adjusts the intervention time
of the Encoder in closing
35
35
* 70
* 70
* 40
* 40
* 75
* 70
* 70
ON
- - - - -
Shows the absorbed current
by the motor during the
movement. The letter H at the
left of the current value
indicates the exceeding of the
set inversion threshold.
57 - WORKING CURRENT
100% Maximum torque
10% Minimum torque
Enables the reading of
the potentiometer with
LE card.
Potentiometer
Reports the current position
of the potentiometer on the
leaf.
This parameter is useful for
seeing if the potentiometer
is read correctly.
Reports the impulses
stored by the control unit
when the leaf is fully open.
Reports the impulses stored
by the control unit when the
leaf is fully close.
32 - ENCODER * Off
- - - - - - - -
51 - I.PAR.M1 *
52 - I.AP.M1 *
53 - I.CH.M1 *
- - - - - - - -
- - - - - - - -
Note: Menus 47 and 48 are only present if the encoder is ON.
English

33
MENU SP Default
SET Description Set Value
0.0 5.0
Pre-flashing only
active before closing
85 - PREFLASHING Only closing
Pre-flashing time
0.0
1 100
82 - MOTOR RELEASE
Off Disabled
Setting from 1 to 100
Off
Buzzer Buzzer
86 - FLASHING LIGHT
Normal
Light
Always
Normal
Control lamp
Always ON Normal
Off
Off
On
The flashing light remains
ON with active timer and
open gate
The flashing light remains
OFF with the active timer
and open gate
87 - FLASHING LIGHT
AND TIMER
Off
Off
79 - ANTI INTRUSION Only closing
Only opening
Opening and closing
If you force the gate
manually, the control
unit starts the motor to
restore the state of the
gate before forcing.
0 100
Adjust the tolerance between
stop and obstacle opening
72 - OPENING TOLERANCE
MOTOR1 0
0 100
73 - CLOSING TOLERANCE
MOTOR1
Adjust the tolerance between
stop and obstacle closing
0
60 - CLOSING
SLOWDOWN 1 *
59 - OPENING
SLOWDOWN 1 * * 30
* 30
Off
5 100
Off
5 100
Disabled
Disabled
Setting from 5 to 100
Setting from 5 to 100
Acceleration ramp.
Adjusts the motor start.
0 15 6 %
0 15 6 %
70 - OPENING POSITION
RECOVERY
71 - CLOSING POSITION
RECOVERY
Retrieves the inertia of the
motor in opening after Stop
or reversing
Retrieves the inertia of the
motor in closing after Stop
or reversing
63 - DECELERATION
Adjust the passage
between normal speed
and slowdown speed
64 - ACCELERATION * * 70%
10%
Off
100%
0 %
100%
English

34
MENU SP Default
SET Description Set Value
Always AUX output always
power supplied
94 - 24V AUX
(Max. 300 mA)
In cycle
In pause
Opening
Closing
AUX output power
supplied only during opening
AUX output power
supplied only during closing
AUX output power
supplied only during pause
AUX output active only
during cycle
Always
Fototest
In cycle and fototest
AUX output only during cycle
with fototest function active
AUX output for
connection of photocell
TX to autotest
Positive brake management
Positive Electrobrake
(output only when the
motor is stopped )
Negative brake management
Negative Electrobrake
(output only during cycle)
1 flash per sec. in opening
2 flashes per sec. in closing
Steady lit in Stop or Open.
Gate open warning
light
92 - TIMER
Off
On photo2 Off
On pedestrian entry
Transforms the selected
input in an input on
which to connect an
external clock.
Off on Off
89 - TRAFFIC LIGHT
RESERVATION
When setting this function
the pedestrian input will be
activated to work on the
auxiliary board SEM
(traffic light management).
20 100 30
90 - PEDESTRIAN OPENING
Setting from 20 to 100
= Start
91 - PEDESTRIAN PAUSE
Pause in pedestrian opening
same as in total opening
= Start
Off Disabled
1 240 Setting from 1s to 4 min.
In cycle
With J1 between 1 and 2,
and J2 not inserted, on CN5
you will have a dry contact
with activation of one "
second at each start impulse."
With J1 between 2 and 3,
and J2 not inserted, on CN5
you will have 24 volts always.
With J1 between 2 and 3, and
J2 inserted on CN5, you will
have 24V only during the cycle.
With J1 between 2 and 3, and
J2 inserted on CN5, you will
have 24 volts only during the
cycle plus for the set time.
Dry contact
1 240
Always
In cycle
88 - COURTESY LIGHT
English

35
MENU SP Default
SET Description Set Value
104 - SELECT LIMIT SWITCH *
Mechanical limit switch
Magnetic limit switch
Mechanical
Magnetic
Mechanical
Active in opening
and closing
Photocell active before
opening
Stop
Opening and closing
Closing Photocell active in closing
98 - PHOTO2
The photocell gives a
command to close during
opening, pause and
closing
The photocell stops in closing
and closes when released
Stop and close
Close Opening
And
clousure
The photocell charging the
pausing time
Pause reload
Delay pause time
99 - PHOTO OFF IN CLOSING 0 50 0
Setting from 0 to 50
95 - FOTOTEST
Photo1
Photo2
Photo1-2
Auto-test active only on
Photo1
Auto-test active only on
Photo2
Auto-test active on
Photo1 and Photo2
Photo1-2
Stop
97 - PHOTO1
Opening and closing
Closing
Stop and close
Close
Pause reload
Active in opening
and closing
Photocell active in closing
Photocell active before
opening
The photocell gives a
command to close during
opening, pause and
closing
The photocell charging the
pausing time
The photocell stops in closing
and closes when released
Closing
Delay pause time
If the photocell is occupied
during opening, pause or
closing, the gate reopens
completely and closes
without observing the
pause time.
100 - EDGE
8K2
Edge is active and
protected by a 8K2 resistor
Normal N.C. contact
Edge works as a photocell
protected by a 10K resistor.
See page 43.
Normal
Photo1 10K
Normal
Allows to connect n. 2
8K2 protectec edges
8K2 Double
If the photocell is occupied
during opening, pause or
closing, the gate reopens
completely and closes
without observing the
pause time.
English

36
105 - MASTER-SLAVE
Master
Slave
Off
Off
For applications with two
motors in master-slave,
you can set the control
unit as slave
For applications with two
motors in master-slave, it
allows to set the control
unit as master
Disabled
1 10
Shows last event
106 - DIAGNOSTICS
0 10E9 0
100 10E4 10E3
107 - MAINTENANCE CYCLES
108 - PERFORMED CYCLES
Setting from 100 to
100000
Reports the executed
cycles. Keep pressed OK
to reset the cycles
112 - PASSWORD - - - -
Allows the entering of a
password blocking the
control unit parameters
modification.
- - - -
When ON, if no mains power
and batteries connected, the
gate will open fully and will
remain open until the power
returns. At this point it will
perform an automatic
reclosing.
113 - EMERGENCY Off On
Off
MENU SP Default
SET Description Set Value
Press OK to exit the special menu.
The special menu switches off automatically after 20 minutes.
120 - BASIC MENU
Note 1: The * indicates that the default value or the menu may change depending on the selected motor type.
Note 2: After initialization the parameters "motor type" and "limit switch type" remain son the value chosen in the setup
program.
Note 3: Display writing speed set on 30% keeps writing slow; Display writing speed set on 100% keeps writing fast.
Please note that speed does not change on JOLLY 3 display.
From 30% to 100%
See note 3 below
80%
119 - DISPLAY WRITING
SPEED
English

37
MENU
SEA
SET
DISPLAY INPUT STATUS
When the segment
is ON during self-
learning, the input
status is closed or
OFF.
Start
Start
pedestrian
Stop
Limit
Switch
opening
motor 1
Photocell 1
Photocell 2
Edge 1
Limit
Switch
closing
motor 1
Initial system
Software Version
Programming example
UP
OK
UP
UP
UP
DOWN
DOWN
DOWN
OK
OK
OK
DOWN
UP
0.0V
MENU
Exit menu
MENU FUNCTION TABLE CHECK USER1 24V DG MAXI INPUTS
To access the Menu for input check keep pressed OK for about 5 seconds.
Description Description
Start test The contact must be N.O. If activating the related command on the
display the item SET lights up, the input will be working.
If SET is always on, check the wirings.
Stop test
Pedestrian
start test
The contact must be N.C. If activating the related command on the
display the item SET lights up, the input will be working.
If SET is always on, make sure that the contact is a N.C. one
The contact must be N.O. If activating the related command on the
display the item SET lights up, the input will be working.
If SET is always on, check the wirings
Safety
edge test
Photocell 1
test
Photocell 2
test
The contact must be N.C. If activating the related command on the
display the item SET lights up, the input will be working.
If SET is always on, make sure that the contact is a N.C. one
The contact must be N.C. If activating the related command on the
display the item SET lights up, the input will be working.
If SET is always on, make sure that the contact is a N.C. One
The contact must be N.C. If activating the related command on the
display the item SET lights up, the input will be working.
If SET is always on, make sure that the contact is a N.C. one.
Opening limit
switch test
Closing limit
switch test
The contact must be N.C. If activating the related command on the display
the item SET lights up, the input will be working. If SET is always on,
make sure that the contact is a N.C. one or that the related
limit switch is not occupied.
The contact must be N.C. If activating the related command on the display
the item SET will light up, the input will be working. If SET is always on,
make sur that the contact is a N.C. one or that the related
limit swith is not occupied.
Batteries’
voltage level Batteries charge level indicator
OK
OK
OK
Note: If the Stop, Photocell 1 and Photocell 2 contacts are not bridged in self-learning, they will be deactivated
and can be reactivated through this menu, without repeating times self-learning.
OK
INPUT CHECK MENU
- - -
- -
- - -
VERG
SLIDING
JOINT
U.001
MOTOR
LIMIT SWITCH
CLOSING
LIMIT SWITCH
OPENING
START
EDGE
PHOTO1
PHOTO2
PEDESTRIAN START
END
STOP
Enabled
Blocked
Enabled
Blocked
Enabled
Blocked
Enabled
Blocked
The settings of the control unit are made through the UP, DOWN and OK buttons. The UP and DOWN buttons to scroll through the MENUS and
SUBMENUS. By pressing OK you enter from MENU into SUBMENU and confirm the choice.
Moving in the menu pressing the UP and DOWN buttons at the same time you access the SP MENU for special settings. 1-LANGUAGE
Moving in the menu pressing the OK button for 5 seconds, you enter the CHECK MENU, where you can check the operating 1-LANGUAGE
status of all inputs.
English

38
RADIO TRANSMITTER SELF LEARNING
WITH RECEIVER ON BOARD OF CONTROL UNIT
!
WARNING: Make the radio transmitters programming before you connect the antenna and insert the receiver into the
special CMR connector (if available) with turned off control unit.
With RF UNI and RF UNI PG module it will be possible to use both Coccinella Roll Plus transmitters and radio transmitters with fixed
code. The first memorized radio transmitter will determine the type of the remaining radio transmitters.
If the receiver is a Rolling Code, press twice the button of the radio transmitter that you want to program to memorize the first TX.
In the case of transmitters with fixed code it is necessary to press 1 time the button of the transmitter you want to program to store the first
remote control
Notes:
- Enter radio transmitters learning only when the working cycle stops and the gate is closed.
- You can store max. 2 of the available 4 functions. If the control unit receives a code which was already associated to another function it will be
updated with the new function.
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
SET
START
PEDESTRIAN
START
EXTERNAL
MODULE
STOP
DELETE A
TRANSMITTER
0OK? OK
CLEAR
MEMORY OK
PRESS
BUTTON STORED
STORED
STORED
STORED
PRESS
BUTTON
PRESS
BUTTON
PRESS
BUTTON
If you want to program
the pedestrian
start as second
channel.
If you want to
delete a single
transmitter.
If you want
to delete the
whole memory
If you want to program
the activation
of the LIGHT
output
as second channel.
Press the
button of the
transmitter
to be stored
Press the
button of the
transmitter
to be stored
Press the
button of the
transmitter
to be stored
Select with
UP or DOWN
the memory
location
to be deleted
and press OK
Press the
button of the
transmitter
to be stored
If you do not want to execute the cancellation,
press UP or DOWN to return to the
2-TRANSMITTER menu.
Confirm the cancellation.
If you want to
program the
UNLOCH as
second channel.
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
UNLOCH STORED
PRESS
BUTTON
Press the
button of the
transmitter
to be stored
If you want to
program the
STOP as
second channel.
OK
for 10 s.
MENU
SEA
SET
OK
TRANSMITTERS
OK
UP
OK
OK
OK
OK
OK
OK
MENU
SEA
SET
MENU
SEA
SET
If you want
to exit the
TRANSMITTERS
menu
Menu output
END OK
OK
1 2 3 4
0
1
2
3
TABLE EXAMPLE
Transmitter
button
Memory
location Serial number Customer
1 2 3 4
0
1
2
3
Transmitter
button
Memory
location Serial number Customer
16 USERS Whitout memory
800 USERS With additional memory MEMO
100 USERS Fixed code
800 USERS Roll Plus
800 UTENTI Fixed code
800 UTENTI Roll Plus
RF UNI
RF UNI PG
RF UNI PG
Old model without additional memory
New model with MEMO additional memory
English

39
CNS
CNS
RADIO TRANSMITTER SELF LEARNING
WITH RF FIX RECEIVER ON BOARD OF CONTROL UNIT
!
Connect the receiver on
the CNS connectors,
making sure that the
direction is the
one shown in the
illustration.
WARNING: Make the radio transmitters programming before you connect the antenna and insert the receiver
into the special CNS connector (if available) with turned off control unit.
With the RF FIX module it will be possible to use only radio controls with fixed code.
Select through the display 2-TRANSMITTERS and press OK, now select with the UP and DOWN buttons, the command to which
you want to associate the button (it is possible to associate max. 2 commands) and press OK to confirm the choice, now press the
button of the radio transmitter which you want to associate. If the storage is successful, the display will show “Stored” .
In the 2-TRANSMITTERS MENU it is possible to select “Start” (to associate a Start command), “Pedestrian start” (to associate a
Pedestrian Start ), “External Module” (For the activation of a contact on the EXP output), “Stop” (To associate the STOP
command to the TX), “Unloch” (to associate the release of the electric brake to the transmitter), “Delete a transmitters” (To delet
the single transmitter only if it is a Rolling Code Plus), “Clear memory” (To delete all TX), “End” (To exit menu 2-TRANSMITTERS).
To release the electric brake it is necessary to give three consecutive pulses, the 4th will reactivate the lock of the electric brake.
Notes:
- Enter radio transmitters learning only when the working cycle stops and the gate is closed.
- It will be possible to memorize up to max. 16 codes (buttons) adding the MEM memory it will be possible to store up to 496
different codes.
- You can store max. 2 of the available 4 functions. If the control unit receives a code which was already associated to another
function it will be updated with the new function.
DELETE TRANSMITTERS FROM THE RECEIVER
With modules different from RF FIX, it will be possible to delete only the entire memory of the receiver.
Proceed as follows: select from the menu 2-TRANSMITTERS: “Clear memory” and hold the OK button until the display shows the
message “OK”.
English

40
START (N.O.) The START is connected between the clamps 2 and 3 of the CN 1 terminal.
An impulse given to this contact opens and closes the automation depending onthe selected logic it can be given by a key switch, a keypad,
etc. To connect the other devices refer to the related instructions leaflets. (ie. loop detectors and proximity switches).
Note1: In DEAD MAN logic it is necessary to keep pressed the Start for the opening of the automation.
Note2: In 2 BUTTONS logic this button performs the opening.
STOP (N.C.) The STOP is connected between the clamps 2 and 5 of the CN1 terminal .
The pressure on this button immediately stops the motor in any condition/position. A start command is needed to re-start the movement.
After a stop the motor always re-starts in closing.
Photocell 1 and Photocell 2 Connections
+ = 24V (Accessories) max 750mA COM = 0V PH1 = Photocell contact 1
PH2 = Photocell contact 2
Note: For the autotest connect the TX to the AUX clamp and activate the Autotest function.
The standard setting of the photocell 1 is in “Closing” and the one of the photocell 2 is in “Opening
and losing” . The photocell 2 can be set also as TIMER (see TIMER function).
Note3: On the 95-FOTOTEST menu you can also activate the self-test even on the single photocell.
START - STOP - PEDESTRIAN START - ANTENNA -
PHOTOCELL
Can be activated through on-board display or through the Jolly 3 programmer. In both cases it’s a N.O. contact which
provoques the opening of the automation keeping it open until it is activated. When it’s released, the gate attends the set
pausing time and executes the reclosing. The TIMER command can be activated on the inputs FOTO2, START PEDESTRIAN.
Note1: When activated on the pedestrian entry, the pedestrian will be disabled also on the radio transmitter.
Note2: In case of intervention of a security device during the timer (Stop, Ammeter, Edge), to restore the movement it will be
necessary to give a start impulse.
Note3: In case of no power supply with open gate and active Timer the control unit will restore its use, otherwise if during
restore of the power supply the TIMER is not activated it will be necessary to give a start impulse for the reclosing.
TIMER
Common Common Photocell 1 Photocell 2
Common 24V (Accessories)
PEDESTRIAN START (N.O.) The pedestrian start can be connected
between the clamps 2 and 4 of the CN1 terminal .
This input allows a partial opening the opening space can be set through
the on-board display or through the JOLLY device.
Note1: The contact for partial opening is a N.O. Contact (Normally open).
Note2:In 2 BUTTONS logic it is necessary to press the Start Ped. to re-
close the automation.
Note3: In dead man logic this button executes the re-closing if you keep it
pressed.
Note4: When closed during pause, the gate will reclose only after this
input has been reopened.
TIMER activation: This input can be transformed into TIMER (See
TIMER).
Options AUX 24V max 300mA can be set with on-board
Display or with Jolly 3 device.
Through the Jolly 3 programmer it is possible to chose when having
tension on the AUX output. The options are: Always, In cycle,
Opening, Closing, In pause, Fototest, In cycle and fototest,
Positive brake management, Negative brake management, Gate
open warning light. When using control units with batteries and /
or solar panels, we recommend connecting the accessories which
are not used when operator stands still (e.g. photocells) to a AUX
output, setting the option “In cycle”. With this setting you can save
energy by lowering power consumption in stand-by, increasing the
autonomy of the system.
OPTIONS ON FOTO1 and FOTO2 adjustable on on- board display or with JOLLY 3
terminal.
“Closing”: if occupied, reverses the movement in closing, during pause it prevent the
closing.
“Opening and closing”: If activated the photocell blocks the movement as long as it’s busy,
when released the opening continues.
“Stop”: When activated before the opening the photocell blocks the automation as long as it
is busy, during the opening it will be ignored. In closing the intervention of the photocell
causes the reopening.
“Stop and close”: in opening it is not active; in pause are activated it commands the closing
when released, otherwise it’s not active; in closing it stops the movement as long as it is busy,
when released the closing continues.
“Close”: The photocell stops the gate as long as it is occupied in both opening and closing,
when released it gives a closing command (Closing one second after release of the
photocell).
“Pause reload”: If occupied, during pause it recharges the timer of pause. In closing it
reverses the movement.
“Delay pause time”: If the photocell is occupied during opening, pause or closing, the gate
reopens completely and closes without observing the pause time.
9 10 11 12 13
1 2 3 4 5 6 7 8
Antenna Start Start partial opening Stop
CN1
RX1
RX2
TX1
TX2
CN1
English

41
LIMIT SWITCH AND SENSOR BARRIERS
Sensor barriers
This control unit comes with a detection device of motor current absorbtion which allows to reveal possible
obstacles during the opening and the closing of the gate. When this device intervenes in opening it causes
the inversion of the movement for around a second, if it intervenes in closing it causes the total reopening.
Note1: The sensitivity is adjustable both in opening and in closing through the on-board display or
through the JOLLY 3 terminal. With high torque the gate reverses after 5 seconds.
Attention: In case of obstacle, if the automatic reclosing is on, the gate will attempt to close for 3
times, whereupon a start signal will be necessary to re-establish the movment.
ALARMS INDICATIONS
Flashings Number
9
2
3
6
4
Flashings Number
5
7
6
4 fast
Kind of alarm
Motors fault
Photocell in closing
Photocell in opening
Opening impact
Safety edge
Kind of alarm
Stop
Max. Reached cycles
Closing impact
Limit switch error
Limit switch
The limit switch can be connected through the special LIMIT SWITCH connector on the control unit.
The control unit can administrate mechanical, inductive and magnetic limit switches. Only on some
special applications il will not be necessary to connect the limit switches. The control unit will
automatically realize if limit switches are present or not.
1) Through the on-board display or through the JOLLY 3 programmer it is possible to activate the ani-
intrusion function. This function is lied to the presence of at least one limit switch which, when free,
forces the motor to re-close.
Note: if during programming phase the motor and limit switch times should not be in phase
between them, the gate will start in closing, it stops and will not complete the selflearning of the
times, at this point it will be necessary to switch off the tension and to invert the cables of the
motor. The first movement in selflearning must always be executed in closing.
ATTENTION: When using SEA magnetic limit switches, make sure that the motor is set on
“Magnetic” present in the special menu 104-SELECT LIMIT SWITCH.
Note 1: If in the diagnostics shows "max. cycles reached ", do the maintenance and / or reset the number of cycles performed.
Note2: To exit from the error messages, press OK. If the error persists, make all required checks for the specific error and / or disconnect the
device that generates the error to see if the error disappears.
At each opening and closing of the automation the flashing light will blink. It blinks once per second during opening and twice per second
during closing, while it remains lit during pause.
It is possible to view the alarms also on the flashing light or on the control lamp, simply by observing the number of flashes emitted and
verifying the reference in the table below:
Note:
limit switch connection in
case of absence of the
plug-in connector.
Limit
Switch
CN2
CN3
COM
CN1
9 10 11 12 13
24V power supply
failure
Failure overcurrent-
collision
Check for obstacles or points of friction on the gate.
NOTE: the fault is reset by pressing OK
FAILURE
OVERCURRENT-
COLLISION
Signals Kind of alarm Solutions
Motor current failure
Autotest photocells failure
Limit switch activation
failure
Make sure there are no short circuits on the motor or on the control unit
Make sure there are no short circuits on the wiring or on the control unit
and no overloads.
Check the photocells operation and / or connections on the control unit.
Check the operation of both limit switches and / or correspondence
between movement direction of the motor and engaged limit switches.
Potentiometer’s direction
failure
Invert potentiometer’s cables (invert green with brown)
FAILURE MOTOR
FAILURE24
FAILURE AUTO-TEST
FAILURE LIMIT SWITCH
FAILURE
POTENTIOMETER
FAILURE POT.1 DIRECTION
Potentiometer failure
The message appears only if the potentiometer is ON and the
potentiometer (LE) card is broken or not connected.
OVERLOAD EXIT 10
CONNECT
ACCESSORIES EXIT 12
FAILURE 24VAUX
Edge’s failure
Check edge’s metal thread and edge’s connection cables; make sure the
contact is closed by looking on display.
FAILURE EDGE
Failure slave function
Check the Master/Slave circuit’s connection and be sure the function Slave
is set on Slave circuit (105-menu).
FAILURE SLAVE
10K photocell failure
Check photocell connection or possible short circuits; check if photocell is
well powered. Make sure that a 10K protection photocell has been connected
FAILURE PHOTO1 10K
AUX output
voltage failure
Make sure there are no short circuits on wiring or control unit and no
overload.The 24Vaux exit is an output which can be set with a maximum
load of 500mA; if you do not require an adjustable 24V, use the 24V
present on terminal 12 (+) and use the negative on exit 11 (COM) and
NOT on exit 13.
FAILURE BLOCKED
MOTOR
PRESS OK TO RESET
Motor current failure
-Be sure there are no short circuits on the motor or on the control unit
-Check that the gate is not locked or stuck in stop
-Check that the encoder (if active) is connected to the control unit
-By unlocking the gate, try giving a start and hear if the motor runs dry
If the motor does not run at all, then it is burned, therefore call our technical
support; If the motor is running, it is recommended to unplug the power
cord, lock the gate again and restore the power
Photocell failure
Check photocell connection or possible short circuits; check if photocell is
well powered
FAILURE PHOTO
Encoder failure
(on SLIM and B800
motors only)
Check Encoder connections; check on Menu-32 if Encoder is ON;
check if motor is blocked.
FAILURE ENCODER
English

42
MOTOR POWER SUPPLY
Power input
Input for the connection of the
electric power.
P = PHASE
N = NEUTRAL
G = GROUND
NOTICE: for the
connection to the
electric power see
the law in force.
TRANSFORMER
3,6A blow fuse on 230V ~ power supply
6,3A blow fuse on 115V ~ power supply GN
115V~
o
230V~
P
P G N
MOTOR
(CN6)
M+ M- 12
EXTERNAL RECEIVER
Example: Connection of a radio receiver
For the connection of the receiver refer to
the relative instructions manual.
Common Common
24V (Accessories)
POWER
(CN8)
P G N
1 2 3 4 5 6 7 8 9 10 11 12 13
+
-
CN1
Start
Start ped.
English

English
43
Flashing Lamp 24V (Accessories) 3W max. (Control lamp)
The Flashing Lamp can be connected between the 24V clamps (Accessories) and
FL (-) of CN 1. The Flashing lamp advises that the automatic gate is moving with 1
flash/second in opening and 2 flashes / second in closing. During pause it remains
switched on. Through the warning lamp it is also possible to identify alarms lied to the
STOP, PHOTOCELL 1, PHOTOCELL 2 and EDGE devices. Through the display or
the JOLLY 3 programmer it is possible to activate the pre-flashing function and/or to
modify the function of the warning lamp choosing between fix flashing or control
lamp.
The pre-flashing can be timed from 0 to 5 seconds otherwise it is possible to
set it before closing only.
WARNING LAMP - SAFETY EDGE - 10K PHOTOCELL - BUZZER
IMPORTANT NOTE: INSTEAD OF THE FLASHING LAMP, IT IS POSSIBLE TO
CONNECT A BUZZER; REMEMBER TO SET THE
86 - MENU ON « BUZZER »
24V FLASHING LAMP 3W MAX 12 and 13
Edge Common
24V (Accessories)
FL(-)
9 10 11 12 13
CN1
Example of a Flashing Lamp
and an Edge connections
Safety edge
Buzzer (24V ) Audible Alarm
Use an autoswinging buzzer 24V of 100 dB.
The buzzer will be switched on after two consecutive activations of the entrapment protection.
To reset the allarm it is necessary to push the button STOP.
Anyway after 5 minutes the buzzer will stop to sound and the automation stands still waiting for commands.
If Buzzer does not work, check the 86-FLASHING LIGHT menu is set on “Buzzer”
!
SAFETY EDGE 9 and 11
Between clamps 9 and 11 on the terminal CN1 it is possible to connect an active Safety Edge. When pressed, the Safety Edge
opens the contact causing a partial inversion of the movement both in opening and in closing. The Safety Edge output can be
set «only in closing», «only in opening» or both directions
Note1: Note1: Through the on-board display or the JOLLY 3 programmer it is possible to activate the balanced edge 8K2, in
this case the edge contact is controlled by a special resistance value revealing the eventual involuntary short- circuit of the
device. In case of imbalance of the device a special alarm will be shown on the on-board dispaly or on the JOLLY programmer.
Note2: Self-test can be made also on a radio powered Edge (See Auto-test Menu)
24V BUZZER 12 and 13
10K PHOTOCELL 9 and 11
Between clamps 9 and 11 on the terminal CN1 it is also possible to connect a 10K
Photocell. In this case it is necessary to set it on menu 100 - EDGE as Photo10K,
then it will run following settings on menu 97 - PHOTO 1.
Nota1: The use of a 10K Photocell allows to get further protection in case of
short-circuit on the cables.
10K
Photocell
CN1
9 10 11 12 13
Edge
BROWN
Common
FL(-)
24V (Accessories)
-
+
BUZZER
BLU
WHITE
GREY
E
Example of a 10K Photocells
and a Buzzer connections
MENU
SEA
SET
100-EDGE 1
MENU
SEA
SET
PHOTO 10K
.
OK
MENU
SEA
SET
OFF
Setting
10K Photocell
MENU
SEA
SET
100-EDGE 1
OKOK
MENU
SEA
SET
PHOTO 10K
.
MENU
SEA
SET
UPUP
OFF

English
44
MagLock
MAGLOCK 12V CONNECTIONS
COM
CN1 (11)
1 2 3 4 5 6 7
Art.23105340
AUX
CN1 (10)
COM
NO
NC
COM
12V DC
NOTE: Please set 94-24V AUX menu to “Negative brake management”.
{
External
power supply
12V / 24V DC
DRAWING SHOWS HOW TO
EVENTUALLY CONNECT THE
MAGNETIC LOOP
Safety exit
loop 1
Loop1
Loop2
Loop3
Shadow
loop 2
Free exit
loop 3
10 11 12 13
1 2 3 4 5 6 7 8 9
-
CN1
C
12
7
6
8
6
3
6
Safety exit loop (loop 1)
Connecting scheme of
loop detector 1 reader
7 = Contact photocell 1 (N.C.)
6 = Common
Shadow loop (loop 2)
Connecting scheme of
loop detector 2 reader
8 = Contact photocell 2 (N.C.)
6 = Common
Note: Please set 98-
PHOTOCELL2 - LOOP2
menu to “Shadow loop”.
Free exit loop (loop 3)
Connecting scheme of loop
detector reader
3 = Contact start (n.o.)
6 = Common
C2 C2C1
C1 = CONTACT OPEN
C2 = CONTACT CLOSED
12 = 24 V
C = 0 V
SAFETY LOOP CONNECTIONS
6
Brown
Green
Pink
Yellow
Grey
NOTICE :
SHADOW LOOP NOT YET
AVAILABLE