SEA GATE 1 DG R2BF User manual

GATE 1 DG R2BF GATE 1 DG R2EF GATE 1 DG R3BF
IT - EN - FR
QUICK START
International registered trademark n. 804888
67412250 REV. 01 - 06/2023
SEA S.p.A.
Zona Industriale Sant’Atto - 64100 - Teramo - ITALY
Telephone: + 39 0 861 588341
www.seateam.com
CONTROL UNIT TO MANAGE
230V or 110V OPERATORS
FULL MANUAL
(Rev. 16)
&
SAFETY
INFORMATION

Italiano
ENGLISH
International registered trademark n. 804888
1 - COMPONENTS
     
20
2 - QUICK START SEQUENCE:
21
21
      
    
WIRINGS
A
21
A1
BBASIC MENU SETTINGS
       « » 
CMOTOR OPERATION TEST (MENU 192)
WORKING TIMES LEARNING
E
GATE 1 DG control unit requires the working times learning procedure!
it is not possible to start the operator correctly without first programming the control unit!
23
23
3 - TMENU TABLE
 
DACTIVATION OF ENCODER  POTENTIOMETER (IF INSTALLED)
23
    
     
A2
A3
A4
22
22
22
23
23
23
23
B1
B2
B3
B4
24
24
24
25
27
E1
E2
E3
E4
E5
26
28
 
 
24
INDEX
  -  1
   -  6
   -  3
         -  7
       «» 
     SEA  
     
25
25
E6           
19

1
Common
Light (-)
*24VAUX 500mA max.
UP DOWN OK
BLACK WHITE RED
EXTERNAL MODULE
CONNECTOR
JOLLY3/SEACLOUD
CONNECTOR
RF RECEIVER
CONNECTOR
PRIMARY
SECONDARY
CONNECTOR
OPEN
(Firmware update)
RF FIX RECEIVER
CONNECTOR
PROGRAMMING
BUTTONS
* All the 24V inputs support a maximum load of 500mA, referred to the sum of the loads of all 24V
accessories connected, including the absorption of the receiver on board (30 mA)
ANT COM START STPD STOP COM PH1 PH2 EDGE1 24VAUX COM 24V(FL) FL(-)
OPTIONAL JUMPERS
UP DOWN OK
TR1
98
7
6
5
4
3
2
110 13
12
11
CN1
98
7
6
5
4
3
2
110 13
12
11
CN1
CN2
JOLLY
CLOUD
CNS
CNS
CN4
CNA
DISPLAY
CMS
PRIMARY
SECONDARY
EXP
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
NL
CNP
CN7
CN6
CN5
20
19
18
17
16
15
14
20
19
18
17
16
15
14
CN2
CN3
F2
R1 R2
F1
T1
155 mm
85 mm
*24V 500mA max.
(accessories)
NL
Courtesy light (phase)
Courtesy light (neutral)
Motor 1 opening
Motor 1 capacitor
LIGHT LIGHTN MCL MN MOP CAPACITOR
Motor 1 closing
Motor 1 neutral
M
CN3
Neutral
Line
CN4
24Vac *
Max. 150 mA
CN5
CN6
Red/Brown
Blue/White
Black/Green
CONNETTORE
ENCODER
1
Opening limit switch (green)
Closing limit switch (yellow)
Common (white)
* 24V (red)
Opening limit switch (green)
Closing limit switch (yellow)
CN7
CNP
T1
R1
R2
F1
F2
TR1
EXP JOLLY/CLOUD
CMS
CNA CNS
=
=
=
=
=
=
MOTOR CONTROL TRIAC
MOTOR AND COURTESY LIGHT RELAY
MOTOR EXCHANGE RELAY
FUSE 6.3AT (230V) OR 10AT (115V)
FUSE ACCESSORIES 1A
POWER TRANSFORMER
1 - COMPONENTS
Start
Stop
Common
Antenna
Common
Photocell 1
Photocell 2
Partial START
Safety edge
TO RESTORE THE EXCLUDED INPUTS,
ENTER THE «INPUTS MANAGEMENT»
MENU (SEE PAGE 22)
NO NEED TO SET UP THE UNIT AGAIN!
AUTOMATIC RECOGNITION OF THE
N.C. INPUTS NOT IN USE
NO JUMPERS ARE REQUIRED ON THE
N.C. CONTACTS!
Italiano
ENGLISH
International registered trademark n. 804888
Keep the power cables separate from the command cables - always run cables in separate sheaths to prevent interferences!
Make all the wirings when the control unit is not powered!
20
-
+
ANT COM START STPD STOP COM PH1 PH2 EDGE1 24VAUX COM 24V(FL) FL(-)
CN1
+
-
12345678 9 10 11 12 13

A
A1
For the wirings of further
accessories, for encoder or
potentiometer adjustments, for
more functions or more details on
accessories settings, see the
complete technical manual!
WIRING OF THE MAIN ACCESSORIES ON THE CONTROL UNIT
WARNING LAMP
SAFETY EDGE
ANTENNA
START
PARTIAL START
STOP
PHOTOCELLS
1
CN6
RED (24V)
YELLOW (CLOSING LIMIT SWITCH)
13
12
11
10
9
CN1 CN7
GREEN (OPENING LIMIT SWITCH)
WHITE (COMMON)
PRE-WIRED LIMIT SWITCH
YELLOW = CLOSING LIMIT SWITCH
GREEN
=OPENING LIMIT SWITCH
CN5
1
BLACK
BLUE
RED
BLUE P01
BLACK D1
BROWN P11
STANDARD ENCODER «POSITION GATE» LINEAR POTENTIOMETER
BROWN P01
WHITE D1
GREEN P11
«RT» ABSOLUTE ENCODER
2 - QUICK START SEQUENCE
F       A - B - C - D - E        
F    ,          !
Make all wirings when the unit is not powered!
Do not jumper the N.C. inputs not in use!
8
7
6
5
4
3
2
1
CN1
TX1
TX2
CN1
RX1
RX2
Start
Stop
Antenna
13
12
11
910
24V (+)
Common
Common
Common
Photocell 1
Photocell 2
Partial Start
CN1
13
12
11
10
9
24V (+)
SAFETY EDGE
Edge 1
Common
Lamp FL(-)
WIRINGS
BLACK (COMMON)
YELLOW
GREEN
PRE-WIRED
LIMIT SWITCH
NON
PRE-WIRED
LIMIT SWITCH
(EXAMPLE)
NON PRE-WIRED LIMIT SWITCH
Italiano
ENGLISH
International registered trademark n. 804888
USE A 3-POLE SHIELDED CABLE
AND WIRE THE SHIELD ON P11!
DIP SWITCH 1 = OFF
DIP SWITCH 2 = OFF
M1
1 2 4 56 73 89 10 11
M2
DS1
ON
CN1
POT ENC
CNP
+
-
LSE
P01 P02
GND
I3
D1 P11D2 P12 I1 I2 I4
2 1
DS1
2 1
OFF
ON
DIP SWITCH 1 = OFF
DIP SWITCH 2 = OFF
M1
1 2 4 56 73 89 10 11
M2
DS1
ON
CN1
POT ENC
CNP
+
-
LRT
2 1
DS1
2 1
OFF
ON
P01 P02
GND
I3
D1 P11D2 P12 I1 I2 I4
USE A 3-POLE SHIELDED CABLE
AND WIRE THE SHIELD ON P11!
21

A2
A3
Fuse 16AT delayed on 230V~ power supply
Fuse 16AT delayed on 115V~ power supply
A4
POWER
00111110
11110000
03.08
ON
CN2
20
19
18
17
16
15
14
MCL MN MOP CAPACITOR
CAPACITOR
= MCL - M1 CLOSING
= MN - M1 NEUTRAL (BLUE)
= MOP - M1 OPENING
= CAPACITOR
16
17
18
19 - 20
MOTOR 1 (230V)
M
~
WHITE 115V
*
*
NL
CN3
-
-
00111110
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
START
PARTIAL START
STOP
PHOTOCELL 1
PHOTOCELL 2
SAFETY EDGE 1
SAFETY EDGE 2
NOT IN USE
MOTOR 1 OPENING LIMIT SWITCH
MOTOR 1 CLOSING LIMIT SWITCH
NOT IN USE
NOT IN USE
NOT IN USE
NOT IN USE
NOT IN USE
NOT IN USE
11000000
00111110
11000000
START
(N.O.)
START
(N.C.)
10111110
11000000 11000000
00111110
11000000
00101110
OPERATOR WIRINGS
Wirings of the operator to the control unit
Control unit wiring to the main power supply
(EXAMPLE)
POWER SUPPLY
FOR THE CONNECTION TO THE POWER GRID,
RESPECT THE LAWS IN FORCE!
In case of unstable power supply, the use of an external UPS of
min. 800VA is recommended
Use a 10A differential switch to protect the power supply system
CHECKING OF THE WIRED ACCESSORIES BY THE «INPUTS STATUS» MENU
Turn on the control unit and check for the correct status of the inputs
S  P S   N.O. (0)
A     N.C. (1)
5
SECONDS
EXAMPLE
SOFTWARE
REVISION INPUTS
STATUS
PHOTOCELL 1
(N.O.)
PHOTOCELL 1
(N.C.)
Italiano
ENGLISH
International registered trademark n. 804888
22

* The menu 32 is not visible in case of sliding operator
with «RT» encoder; the unit automatically sets to «RT»
B
B1
B2
B3
B4
C
D
ON
POWER ON
UP OK UP OK
3
MOTOR OK UP OK
When a type is set, the parameters of the special
menu automatically set to useful values for that type!
OK UP OK
6
LOGIC
AUTOMATIC
OK UP OK
10
SECONDS
OK
UP
DOWN
00111110
11000000
03.08
Select the desired working logic. If a pause time
other than zero is set in the following menu, the
automatic reclosing will always be enabled.
Set a pause time other than zero to activate the
automatic reclosing. If set to «0» the automatic
reclosing will be disabled (i.e. so the unit will
operate in «semi-automatic» logic)
If the gate opens by pressing UP and if the
gate closes by pressing DOWN, so the motor
runs correctly, otherwise swap the motor
cables.
UP OK OK UP
32
ENCODER
DOWN
UP
UP DOWN
UP
ON
UPUP
POSITION
GATE
RT *
OFF
OK
03.08
(ESEMPIO)
00111110
UP
28
OP. TORQUE 1
11000000
MOTORS OPERATION TEST (MENU 192)
BASIC MENU SETTINGS
  -  1
   -  3
   -  6
           -  7
ENCODER  POTENTIOMETER ACTIVATION (ONLY IF INSTALLED)
SOFTWARE
REVISION INPUT
STATUS
5
SECONDS
LANGUAGE
ENGLISH
1
EXAMPLE
EXAMPLE
2-SLIDING
EXAMPLE
EXAMPLE
7
TIMER TO
CLOSE
192
MOVE
GATE 1


1
LANGUAGE
16
SPECIAL
MENU
1
LANGUAGE
SPECIAL MENU
INPUTS STATUS
SOFTWARE REVISION
5 SECONDS
HOLD PRESSED
5 SECONDS
TO EXIT THE
SPECIAL MENU
CONFIRM THE
TYPE IN USE
Italiano
ENGLISH
International registered trademark n. 804888
23

E
E1
E2
If the motor starts closing, reaches the limit switch lever and stops, then swap the limit switch cables and repeat the procedure;
a
If the motor starts opening, reaches the limit switch lever and stops, then swap the motor cables and repeat the procedure;
a
E3
a
aUP
ON
5
WORKING TIMES LEARNING
     SEA SLIDING OPERATORS
THE LEARNING CYCLE STARTS:
CLOSE - OPEN - CLOSE
    LIMIT SWITCH
The limit switches are automatically detected
00111110
5
SEC.
UP UP OK UP
ON
OK
OFF ON
POWER
OFF
POWER
ON
(EXAMPLE)
(EXAMPLE)
SOFTWARE
REVISION
LEAF ON HALFWAY
UNLOCK LOCK
INPUTS STATUS
1
LANGUAGE
PROGRAMMING
9
THE LEARNING CYCLE STARTS: CLOSE - OPEN - CLOSE
    STANDARD ENCODER
11000000
03.08
OFF ON
POWER
OFF
POWER
ON
00111110
UP
(EXAMPLE)
(EXAMPLE)
SOFTWARE
REVISION
LEAF ON HALFWAY
UNLOCK LOCK
HOLD
PRESSED
5
SECONDS
5 SECONDS
INPUTS
STATUS
03.08
11000000
(EXAMPLE)
(EXAMPLE)
00111110
5
SEC.
UP UP OK UP
ON
OK
OFF ON
POWER
OFF
POWER
ON
(EXAMPLE)
(EXAMPLE)
SOFTWARE
REVISION
LEAF ON HALFWAY
UNLOCK LOCK
INPUTS STATUS
1
LANGUAGE
PROGRAMMING
9
THE LEARNING CYCLE STARTS: CLOSE - OPEN - CLOSE
11000000
03.08
(EXAMPLE)
REVERSE
MOTOR
If the learning cycle starts in opening, reverse the motors rotation and repeat the procedure
BARRIER: always starting with the beam halfway - about 45° - the learning cycle is: CLOSE - OPEN - CLOSE
Italiano
ENGLISH
International registered trademark n. 804888
24

E4
aUP
ON
5
UP
ON
OFF ON
POWER
OFF
POWER
ON
UP
OK
UP
OPEN WITH SLOWDOWN
CLOSE WITH SLOWDOWN
CLOSE
OPEN
CLOSE
03.08
00111110
11000000
E5     SLIDING OPERATORS WITH «RT» ENCODER
}
UP
CLOSE
O P E N
CLOSE
MANUAL
PULSES
ON STOP
POINTS
UP
ON
UP
OK
UP UP
UP
E6
00111110
5
SEC.
UP UP
*
OK
UP
OPENING DIRECTION
MOTOR 1
DIRECTION
RIGHT
LEFT
}
OK OK
MANUAL
HOLD PRESSED
UNTIL MAX. OPENING
DOWN
HOLD PRESSED
UNTIL MAX. CLOSING
OK
52
I. AP. M1
53
I. CH. M1
STORED
11000000
UP
OPEN AND
PRESS OK
UP OK
STORED
CLOSE AND
PRESS OK
OK
DOWN
OPEN WITH SLOWDOWN
CLOSE WITH SLOWDOWN end-of-stroke points
by 1 cm pitch:
At the end, it is possible to fine-tune the
If the learning cycle starts in opening, reverse the motors rotation and repeat the procedure REVERSE
MOTOR
UNLOCK LEAF ON HALFWAY LOCK
(EXAMPLE)(EXAMPLE) (EXAMPLE)
SOFTWARE
REVISION INPUTS
STATUS
5
SECONDS
1
LANGUAGE
9
PROGRAMMING
    POTENTIOMETER
THE LEARNING CYCLE STARTS:
THE LEARNING CYCLE
STARTS:
OFF ON
POWER
OFF
POWER
ON
(EXAMPLE)
(EXAMPLE)
SOFTWARE
REVISION
LEAF ON HALFWAY
UNLOCK LOCK
INPUTS STATUS
1
LANGUAGE
PROGRAMMING
9
03.08
(EXAMPLE)
MOTOR 1
DIRECTION
OFF ON
POWER
OFF
POWER
ON
03.08
00111110
11000000
UNLOCK LEAF ON HALFWAY LOCK
(EXAMPLE)(EXAMPLE) (EXAMPLE)
SOFTWARE
REVISION INPUTS
STATUS
5
SECONDS
THE LEARNING CYCLE STARTS:
1
LANGUAGE
9
PROGRAMMING
WORKING TIMES LEARNING THROUGH MANUAL PULSES ON THE POINTS OF STOP
(for operators without limit switch, without encoder and without potentiometer -
ie: hydraulic swing operator)
Italiano
ENGLISH
International registered trademark n. 804888
25

SET DESCRIPTION DEFAULT NOTES
Italiano
Italian
English
English
Français
French
Español
Spanish
Dutch
Dutch
Polski Polish
Start
Start
Partial opening
Partial opening
External module
External module
Stop
Stop
Bistable Stop
Pressed once, it stops the gate.
Pressed twice, it reactivates the START input
Latch opening
One impulse opens and keep open.
A second impulse restore the movement
Latch closing
One impulse closes and keep closed.
A second impulse restore the movement
Unlock
To store a command for unlocking the electric brake
Delete a transmitter
To delete a single transmitter (TX)
Move to EEP
Menu available on model
R3BF only
To transfer the transmitters stored on the control unit to
the external EEPROM (MEM), if connected
Clear memory
To delete the full transmitters memory on the receiver
End
To exit the menu "transmitters"
1- Hydraulic
Hydraulic operators
2- Sliding Sliding operators
3- Reversible Sliding Reversible sliding operators
4- Mechanic Swing
Electro-mechanic swing operators
5- Three-phase
and Bollards
Three-phase operators
Bollards
6- Magnetic Sliding Sliding operators with magnetic limit-switch
7- Barrier Barriers
12- B-200 Sliding operator
13- Chain sliding operator
Sliding chain operator
Slowdown OFF - deceleration 70% - Buzzer in ON
PHOTO 2 as shadow loop
14- B-200 chain Sliding chain operator
15- Erg Garage door operator
50- Taurus Mag Fast Chain Sliding chain operator
51- Taurus Rack Fast Sliding rack operator
82- Absolute sliding (RT) Sliding operator with RT Absolute Encoder
GATE 1 DG (R2BF) - (R2EF) - (R3BF) MENU FUNCTIONS TABLE
THE DESCRIBED FUNCTIONS ARE VALID FOR ALL GATE 1 DG VERSIONS, EXCEPT WHERE EXPRESSLY STATED
MENU
1
LANGUAGE
English
2
TRANSMITTERS
Start
Partial
Opening
3
MOTOR
Mechanic
26

SET DESCRIPTION DEFAULT NOTES
On
To reverse the opening with the closing and vice-versa
(both motors and limit-switches are reversed)
Off Off
Automatic
Automatic logic - automatic reclosing enabled
Open-stop-close-stop-open
Step by step type 1
Open-stop-close-open
Step by step type 2
2 button
Two buttons
Safety
Safety
Dead man
Dead man
Off
Semi-automatic logic enabled
(a START command opens and another START closes the
gate - automatic reclosing disabled)
1 240
To set a pause time (from 1 second to 4 minutes) before
the automatic reclosing
Off
The Start command is not accepted during pause
On
The Start command is accepted during pause
Off On To start the working times learning
Motor Direction
This menu is shown oly in case of sliding operators with
"RT" Encoder -it allows to program the operator in
manual mode
10
TEST START Off On To give a Start command for testing the automation Off
13
LATCH PAUSE
Off On
If "ON" the operator complies with the pause time set
when the function "LATCH OPENING" is disabled. When
"OFF" the pause time set is not respected
Off
14
RESET
192
MOVE GATE 1 *
- - - -
15
END
16
SPECIAL MENU
9
PROGRAMMING
Off
Allows the movement of the gate in a temporary "dead man" mode
(for example to test the correct running of the motor)
HOLD UP PRESSED = THE GATE OPENS
HOLD DOWN PRESSED = THE GATE CLOSES
* The command is accepted only at the end of the cycle or after a STOP command; it is not accepted during the cycle and
during the pause
Press OK to return to the display of the firmware version
and to the one of inputs state
Press OK to enter the special menu
A count-down of 5 seconds will start by holding the UP button; at its end "INIT" will appear on the
display as confirmation of the control board reset
5
REVERSE MOTOR
Off
MENU
6
LOGIC
Auto-
matic
7
TIMER TO CLOSE
Off
8
START IN PAUSE
Off
27

SET DESCRIPTION DEFAULT NOTES
25 LEARNING SPEED 50% 100 %
To adjust the working times learning speed.
The menu is shown only if the 3-MOTOR menu is set to
"50-TAURUS MAG" or to "82-Absolute Sliding"
50
28
OPENING TORQ 1 10 100
Motor 1 opening torque:
by increasing the torque, more strength will be required to
execute the inversion in case of obstacle.
with hydraulic motors the torque will be on 100%
It
depends
on
model
29
CLOSING TORQ 1 10 100
Motor 1 closing torque:
by increasing the torque, more strength will be required to
execute the inversion in case of obstacle.
with hydraulic motors the torque will be on 100%
It
depends
on
model
32
ENCODER On
ON = Encoder enabled
OFF = Encoder disabled
(when OFF, the working times learnt are only shown)
Off
47 ENCODER PAR.
M1
xxx.
48 ENCODER TOT.
M1
xxx.
Position Gate
To enable the reading of the potentiometer
(only if connected via LE or LSE management unit)
RT
To enable the reading of the Absolute Encoder
(only if connected via LRT management unit)
51 I.PAR. M1 *- - - - - - - -
52 I.AP. M1
From the value learned
to ± 100 pulses
53 I.CH. M1
From the value learned
to ± 100 pulses
32
ENCODER Off
ON = Encoder enabled
OFF = Encoder disabled
(when OFF, the working times learnt are only shown)
Off
65 OPENING TIME
M1
xxx.s
66 CLOSING TIME
M1
xxx.s
10% (Fast intervention)
99% (Slow intervention)
To adjust the Encoder or Potentiometer intervention time
on Motor 1 in opening
Off (Intervention excluded) Disabled - Mandatory setting for version R2EF
10% (Fast intervention)
99% (Slow intervention)
To adjust the Encoder or Potentiometer intervention time
on Motor 1 in closing
Off (Intervention excluded) Disabled - Mandatory setting for version R2EF
33
OPENING SENSITIVITY
MOTOR 1
Off
32
ENCODER
Off
THE DESCRIBED FUNCTIONS ARE VALID FOR ALL GATE 1 DG VERSIONS, EXCEPT WHERE EXPRESSLY STATED
To display the learnt value during the working times self learning, in
opening and closing (Motor 1) . With UP or DOWN it is possible to
increase or reduce the working times
* While the partial impulses are displayed, it is possible to OPEN (by pressing UP) or CLOSE (by pressing DOWN) the operator
to verify the correct reading of the potentiometer - Function available only on model R3BF
Impulses read by Encoder during operation (Motor 1)
Impulses stored during programming (Motor 1)
To show the current position of the potentiometer on the leaf moved by
Motor 1. This parameter is useful to see if the potentiometer is
correctly read
34
CLOSING SENSITIVITY
MOTOR 1
Off
SPECIAL MENU
SPECIAL MENU
PRESS AT THE SAME TIME FOR 5 SECONDS TO ENTER OR TO EXIT THE SPECIAL MENU
To show the impulses stored by the control unit when the leaf moved
by Motor 1 is fully open
To show the impulses stored by the control unit when the leaf moved
by Motor 1 is fully close
28

SET DESCRIPTION DEFAULT NOTES
10% (Fast intervention)
99% (Slow intervention)
To adjust the amperometric sensitivity in slowdown
Function available only on electro-mechanic operators
Off (Intervention excluded) Disabled - Mandatory setting for version R2EF
With potentiometer
To set the inversion time in slow-down from 0to 5
seconds (= 99%) - available only if the potentiometer or
the RT absolute encoder have been wired and enabled
It
depends
on model
38
POTENTIOMETER
THRESHOLD
OPENING 1
39
POTENTIOMETER
THRESHOLD
CLOSING 1
42
POTENTIOMETER
SLOWDOWN
THRESHOLD
OPENING 1
43
POTENTIOMETER
SLOWDOWN
THRESHOLD
CLOSING 1
Total
In case of obstacle or safety edge it totally reverses the
movement during closing. If the automatic reclosing is
enabled (automatic logic) , it is attempted for 5 times
Partial
In case of obstacle, safety edge or potentiometer, it
partially reverses direction (of about 30 cm) then stops
59
OPENING
SLOWDOWN 1
Off (*) 50 Adjustable from OFF to the 50% of the stroke
It
depends
on model
60
CLOSING
SLOWDOWN 1
Off (*) 50 Adjustable from OFF to the 50% of the stroke
It
depends
on model
63
DECELERATION 0 %
100%
To adjust the change from normal speed to slowdown
speed
It
depends
on model
64
ACCELERATION 0 %
100%
Acceleration ramp.
To adjust the motor start
It
depends
on model
70
OPENING POSITION
RECOVERY
0 20 seconds
To retrieve the inertia of the motor in opening after the
Stop or the reversing
1s
71
CLOSING POSITION
RECOVERY
0 20 seconds
To retrieve the inertia of the motor in closing after the
Stop or the reversing
1s
72
OPENING TOLERANCE
MOTOR 1
0 100
To adjust the Motor 1 tolerance between the stop and the
obstacle, in opening
0
73
CLOSING TOLERANCE
MOTOR 1
0 100
To adjust the Motor 1 tolerance between the stop and the
obstacle, in closing
0
37
SLOWDOWN
SENSITIVITY
Mandatory setting to
OFF for version R2EF
1 1000
(available only if the
"Position Gate" or the
"RT" Encoder have been
wired)
SPECIAL MENU
Sliding operators equipped with «RT» Absolute Encoder can be set from 5% to 50%
It
depends
on
model
The menus 65 - 66 are shown only if the menu 32- ENCODER = OFF
CLOSING INVERSION
Off
The menus 47 - 48 are shown only if the menu 32- ENCODER = ON
The menus 51 - 52 - 53 are shown only if the menu 32- ENCODER = Position Gate or RT
* For motors with hydraulic brake (CF) or double hydraulic brake (2CF) this parameter must be on Off
1 100
(available only if the
"Position Gate" or the
"RT" Encoder have been
wired)
To adjust the threshold of the Potentiometer or "RT"
Encoder intervention in slowdown.
The value can be manually increased on the condition that
the set value is higher than the value shown in VP1
(instantaneous speed values which can be shown by
accessing the DEBUG menu)
It
depends
on
model
To adjust the threshold of the Potentiometer or "RT"
Encoder intervention.
This parameter self-determines during the working times
learning but can also be adjusted later, on the condition
that the set value is higher than the value shown in VP1 or
VP2 (instantaneous speed values which can be shown by
accessing the DEBUG menu).
NOTE: The lower the threshold value, the slower will be
the response of the potentiometer
It
depends
on
model
46
29

SET DESCRIPTION DEFAULT NOTES
Time
Pushing Off - 3 sec
Stroke
Before opening, the motor starts in closing for the time
set, in order to simplify the lock release
Repeat
Lock Off – On
Release
If ON, the lock will be released both before and after the
pushing stroke
End
To exit the menu
Only opening
Only closing
Opening and closing
Off
Off
Opening and closing
Only closing
Only opening
81
PERIODIC PUSHOVER Off 8h
To activate the repetition of the pushover function at a
distance of time adjustable from 0to 8 hours, at hourly
intervals
Off
Opening 1 Off - 3 s
Closing 1 Off - 3 s
Opening 2 Off - 3 s
Closing 2 Off - 3 s
End
83
EXTRA TIME 0.0 s 10 s
If the limit switches are installed, it is possible to add an
extra time (max. 10 seconds) to the movement of the
operator after the reading of the limit switches
Note: If an Encoder is installed, the space can be set by
impulses (from 0 to 100)
0.0 s
84
BRAKE Off 100% To adjust the braking on the limit switch 0
Only closing
To enable the pre-flashing only before closing (to
access: press DOWN button when 0.0 value is shown)
0.0 10 s
To set the pre-flashing duration
Normal
Normal
Light
Warning lamp function
Always
Always ON
Buzzer
Buzzer
Off
The flashing light will be OFF with enabled timer and open
gate
On
The flashing light will be ON with enabled timer and open
gate
Off
Disabled
1 240
Adjustable from 1 second to 4 minutes
In cycle
Courtesy light only in cycle
89
TRAFFIC LIGHT
RESERVATION
Off On
To get the priority in entry (via a START command) or in
exit (via a PARTIAL START command) .The function is
available only with a traffic light wired via SEM
management unit
Off
90
PARTIAL OPENING 20 100 Adjustable from 20 to 100 100
20
If different from OFF, the operator slightly reverses its
direction at the end of the cycle
Off
(hydraulic)
0.1
(mechanic)
85
PRE-FLASHING
Off
Normal
87
FLASHING LIGHT AND
TIMER
Off
88
COURTESY LIGHT
76
PUSHING STROKE
82
MOTOR RELEASE
Off
80
PUSHOVER
The gate leaf makes an extra movement at the maximum
torque to ensure the tightening of the gate
In case of a STOP command, the Pushover function is
restored only after a new START command
Off
SPECIAL MENU
Off
79
ANTI INTRUSION
If the gate moves, whether due to wind or manual forcing,
the function starts up the operator to restore the initial
position. (function available only if limit switch or
potentiometer or encoder "RT" are installed)
86
FLASHING LIGHT
30

SET DESCRIPTION DEFAULT NOTES
= Start
The pause in partial opening is the same as in total
opening
Off
Disabled
1 240
Adjustable from 1 second to 4 minutes
Off
On Photocell 2
On Partial Start
Off
Disabled
On Photocell 2
The function can be enabled on the Photocell 2 input
On Partial Start The function can be enabled on the Partial Start input
Always
AUX output always powered
In cycle
AUX output powered only during cycle
Opening
AUX output powered only during opening
Closing
AUX output powered only during closing
In pause
AUX output powered only during pause
Phototest
AUX output powered for safety devices testing
In cycle and phototest
AUX output powered only during cycle and for safety
devices testing
Positive brake
management
(connected through relay)
Positive Electric-brake - connected through relay
(AUX output powered only with stationary gate)
Negative brake
management
(connected through relay)
Negative Electric-brake - connected through relay
(AUX output powered during cycle and 1 second before
starting the movement)
Negative brake
(connected through relay)
Photocell management
Negative Electric-brake (AUX output powered during
cycle and 1 second before starting the movement; AUX
output disabled when the photocell is activated)
Open gate
warning light
1 flash per second during opening
2 flashes per second during closing
Steady lit in "Stop" or "Open" status
Lock
(connected through relay)
The AUX output allows the connection of a relay for the
management of a lock Note: to connect the lock, a relay
and an external power supply are necessary
Opening and open AUX output powered during opening and with open gate
Courtesy light
(connected through relay)
The AUX output allows the connection of a relay for the
management of a courtesy light which will work as per
Menu-88 settings
Start 3 s
(connected through relay)
AUX output powered at every Start input or at every
photocells or safety edge intervention, for 3 seconds
(ie. management of lights connected through the relay)
Barrier Led lights
Closed barrier - the light is switched-on
Open barrier - the light is switched-off
Moving barrier - the light blinks
24V AUX
(Max. 500 mA)
The AUX output allows
the connection of a
relay for the additional
accessories
management
91
PARTIAL PAUSE
= Start
94
Off
Always
92
TIMER
The selected input will be turned into an input (on CN1) to
which connect an external clock
Off
SPECIAL MENU
FIRE SWITCH
93
31

SET DESCRIPTION DEFAULT NOTES
Photocell 1
Self-test enabled only on photocell 1
Photocell 2
Self-test enabled only on photocell 2
Photocells 1 and 2
Self-test enabled on photocells 1 and 2
Off Disabled
Safety Edge 1 Self-test enabled only on safety edge
Photocell 1
Safety Edge
Self-test enabled on photocell 1 and safety edge
Photocell 2
Safety Edge
Self-test enabled on photocell 2 and safety edge
All Self-test enabled on photocell 1 and 2 and safety edge
Closing
If the photocell is occupied during closing, the gate
reverses the movement; If the photocell is occupied
during the pause, it prevents the gate reclosing
Opening and closing
If the photocell is occupied during opening or closing, it
stops the gate movement; when the photocell is released,
the movement continues
Stop
If the photocell is occupied before the Start input, the
Start will be ignored. If the photocell is occupied after the
Start input, the photocell will be ignored. If the photocell
is occupied during closing, the gate will reopen
Stop and close
If the photocell is occupied during closing, it stops the gate
movement; when released, the closing movement
continues
Close
The photocell stops the gate until it is occupied in both
opening and closing; when released, it send a closing input
(the gate closes 1s after the photocell release)
Pause reload
If the photocell is occupied during opening or closing, it
stops the gate movement; when released, the movement
continues. If the photocell is occupied during the pause, it
recharges the pause time set
Shadow loop
When the gate is open, the shadow loop prevents the
reclosing until it is occupied. The Shadow loop is switched
off during closing
Delete pause time
If the photocell is occupied during opening, pause or
closing, the gate reopens completely and closes without
observing the pause time set
Shadow loop RP
(pause reloading)
When the gate is open, the shadow loop prevents the
reclosing until it is occupied. When released, the gate
repeats the pause time set, then it closes. The Shadow
loop is switched off during closing
95
PHOTO-TEST
Off
SPECIAL MENU
97
PHOTOCELL 1
SHADOW LOOP 1
Closing
32

SET DESCRIPTION DEFAULT NOTES
Closing
If the photocell is occupied during closing, the gate
reverses the movement; If the photocell is occupied
during the pause, it prevents the gate reclosing
Opening and closing
If the photocell is occupied during opening or closing, it
stops the gate movement; when the photocell is released,
the movement continues
Stop
If the photocell is occupied before the Start input, the
Start will be ignored. If the photocell is occupied after the
Start input, the photocell will be ignored. If the photocell
is occupied during closing, the gate will reopen
Stop and close
If the photocell is occupied during closing, it stops the gate
movement; when released, the closing movement
continues
Close
The photocell stops the gate until it is occupied in both
opening and closing; when released, it send a closing input
(the gate closes 1s after the photocell release)
Pause reload
If the photocell is occupied during opening or closing, it
stops the gate movement; when released, the movement
continues. If the photocell is occupied during the pause, it
reloads the pause time set
Pause reload
Photo closing
If the photocell is occupied during the pause, it reloads the
pause time set. If the photocell is occupied during closing,
the gate reverses the movement
Shadow loop
When the gate is open, the shadow loop prevents the
reclosing until it is occupied. The Shadow loop is switched
off during closing
Delete pause time
If the photocell is occupied during opening, pause or
closing, the gate reopens completely and closes without
observing the pause time set
Shadow loop RP
(pause reloading)
When the gate is open, the shadow loop prevents the
reclosing until it is occupied. When released, the gate
repeats the pause time set, then it closes. The Shadow
loop is switched off during closing
Stop and open
If the photocell is occupied during opening, the gate will
stop; when released, the gate continues the opening
movement. The photocell is ignored during closing
Stop N.O. Stop connection on ERG push-button panel
Safety edge 2
To enable the second safety edge
With models "R2BF" and "R2EF" only the connection of a
Standard Safety Edge (Normal) is allowed
With model "R3BF" the connection of different Safety
Edge types is allowed; Select the type on menu 101;
With all models it is possible to choose the working
direction of the second safety edge by the menu 103
98
PHOTOCELL 2
SHADOW-LOOP2
SPECIAL MENU
Opening
and
Closing
33

SET DESCRIPTION DEFAULT NOTES
Normal Standard safety edge - N.C. contact
8K2
Safety edge protected by a 8K2 resistor enabled
8K2 Double
Two safety edges protected by a 8K2 resistor enabled
Photo 1 10K
Photocell protected by a 10K resistor enabled
Photo 1 10K Double
Two photocells protected by a 10K resistor enabled
Normal Standard safety edge - N.C. contact
8K2 N.C. Safety edge protected by a 8K2 resistor enabled
8K2 N.C. Double Two safety edges protected by 8K2 resistor enabled
8K2 RES Resistive edge protected by 8K2 resistor enabled
8K2 RES Double Two resistive edges protected by 8K2 RES enabled
Normal Standard safety edge - N.C. contact
8K2 N.C. Safety edge protected by a 8K2 resistor enabled
8K2 N.C. Double Two safety edges protected by 8K2 resistor enabled
8K2 RES Resistive edge protected by 8K2 resistor enabled
8K2 RES Double Two resistive edges protected by 8K2 RES enabled
Opening and closing
Safety edge enabled in opening and closing
Only opening
Safety edge enabled only in opening
Only closing
Safety edge enabled only in closing
Opening and closing
Safety edge enabled in opening and closing
Only opening
Safety edge enabled only in opening
Only closing
Safety edge enabled only in closing
Automatic
Automatic detection of the limit switch
Only opening
Limit switch enabled only in opening
Only closing
Limit switch enabled only in closing
Motor internal
To be enabled if the operator is equipped with an inner
limit switch that stops the motor phase
Primary
To set the control unit as PRIMARY on applications with
two operators in primary/secondary mode
Secondary
To set the control unit as SECONDARY on applications
with two operators in primary/secondary mode
Off Disabled
106
DIAGNOSTICS 1 10 To display the last event (See alarms table)
107
MAINTENANCE
CYCLES
100 240000
Adjustable from 100 to 240000 cycles 100000
108
PERFORMED CYCLES 0 240000
To display the executed cycles.
Hold pressed OK to reset the cycles
0
109
THERMOMETER On Off
To enable the probe for measuring the piston oil
temperature; The temperature probe must be connected
via the LE or LSE management circuit
Off
103
SAFETY EDGE 2
DIRECTION
Menu available only
if the menu 98 is set
on "SAFETY EDGE 2"
Opening
and
Closing
104
SELECT LIMIT SWITCH
Automatic
105
Opening
and
Closing
102
SAFETY EDGE 1
DIRECTION
PRIMARY/SECONDARY
(MASTER/SLAVE)
SPECIAL MENU
SAFETY EDGE 1
Menu available on
models R2BF and
R2EF only
Normal
101
SAFETY EDGE 2
Menu available on
model R3BF only and
if the menu 98 is set
on "SAFETY EDGE 2"
100
Normal
SAFETY EDGE 1
Menu available on
model R3BF only

SET DESCRIPTION DEFAULT NOTES
110
LOWER
TEMPERATURE
THRESHOLD
From -20° to +50°
To adjust the temperature threshold to enable the oil
heater (This menu is shown only if the menu 109-
Thermometer is set to ON)
-10°
111
UPPER TEMPERATURE
THRESHOLD
From -20° to +50°
To adjust the temperature threshold to disable the oil
heater (This menu is shown only if the menu 109-
Thermometer is set to ON)
0°
112
PASSWORD
Note: "0000" setting is not
allowed
To enter a password for blocking the control unit
parameters modification
- - - -
Off Disabled
Last opening
In case of power failure, as soon as the battery charge
drops below 22V, the gate opens one last time and
remains open until the power is restored
Last closing
In case of power failure, as soon as the battery charge
drops below 22V, the gate closes one last time and
remains closed until the power is restored
117 ALWAYS CLOSE Off 240 seconds
In case of power failure, if the gate has been manually
open, it closes only after the set time has elapsed (from 0
to 240 sec.) as soon as the power is restored
Off
Off Disabled
Opening
The gate opens and stay open till a new LATCH button
input. The latch function uses the "Partial Opening" N.O.
input
Closing
The gate closes and stay closed till a new LATCH button
input. The latch function uses the "Partial Opening" N.O.
input
119
DISPLAY WRITING
SPEED
From 30% to 100%
See Note 2 at the end of the table 80%
120
BASIC MENU
Normal Standard photocell without 10K control
Photo 1 10K Photocell with 10K control
Photo 1 10K DOUBLE Double photocell with 10K control
Normal Standard photocell without 10K control
Photo 2 10K Photocell with 10K control
Photo 2 10K DOUBLE Double photocell with 10K control
Normal
In case of a power failure or in case of obstacle, the
operator restarts at the normal speed
Deceleration
In case of a power failure or in case of obstacle, the
operator restarts at a lower speed than the normal
190
BASIC MENU
On model R3BF only
122
PHOTO 2 TYPE
Menu available on
model R3BF only
Normal
189
HOMING
This menu is not
available if the menu
3 is set to 50 or 82
Normal
Press OK to exit the special menu.
The special menu switches off automatically after 20 minutes
121
PHOTO 1 TYPE
Menu available on
model R3BF only
Normal
113
EMERGENCY
Off
118
LATCH
SPECIAL MENU
Note 1: after initialization, the parameters set on menu 3 - MOTOR and 104 - SELECT LIMIT SWITCH always remain set to the
value chosen during the programming operation
Note 2: if the menu 119 - DISPLAY WRITING SPEED is set to the minimum value of 30%, the display writing speed will be low.
On the contrary, if it is set to the maximum value of 100%, the writing speed will be very high
Please note: the writing speed will not change on the JOLLY 3 programmer
Off
Press OK to exit the special menu.
The special menu switches off automatically after 20 minutes
35

NOTES
International registered trademark n. 804888

SEA S.p.A.
Zona Industriale Sant’Atto - 64100 - Teramo - ITALY
Tel. [phone] r.a.
www.seateam.com
International registered trademark n. 804888