Sealey SPL01 User manual

FAST LOCK TIE DOWN SYSTEM
MODEL NO: SPL01
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator. It is the operator’s responsibility to secure the load. Check with vehicle manufacturer’s Manual
before installing.
WARNING! Before use, ensure that there is nothing attached to the front forks or the fairing of the motorcycle that will foul the unit.
9Proper use and installation of this product is critical to safety. Improper use may result in personal or property damage which is not
covered by the warranty.
9Proper care and maintenance of the unit is critical to safety.
9Keep the unit clean for the best and safest performance.
9Maintain correct balance and footing whilst positioning the motorcycle in the unit.
9Ensure that the floor is not slippery and wear non-slip shoes.
9Ensure that the motorcycle is adequately secured to the unit if to be used for transportation purposes.
9Keep children and unauthorised persons away from work area.
9Inspect unit before each use. Check fasteners for tightness, replace any worn or damaged parts.
9Before removing a motorcycle from the unit, ensure that there are no obstructions or persons in the path of the motorcycle.
8DO NOT attempt to use a unit that is damaged in any way.
8DO NOT modify the unit in any way.
8DO NOT use the unit for a purpose it is not designed to perform.
8DO NOT operate the unit if it is damaged.
8DO NOT use the unit when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8DO NOT allow untrained persons to use the unit.
2. INTRODUCTION
Securely holds your motocross bike on to a trailer or van, with the Fast Lock system, no ratchet straps or wheel chock required.
Provided with mounting plates and quick release latches, allowing for fast installation and removal of the clamp, freeing your vehicle
 forotheruses.EachmountingplatehasaD-ringcreatingadditionalanchorpointstothetraileroor.
3. SPECIFICATION
Model No:............................................................ SPL01
Foot peg width from tip to tip:18”-20” (455mm-510mm), foot peg height: 15”-17.5” (380mm-445mm)).
TheSPL01isdesignedtot125-500ccbikeswithsimilargeometry(Footpegwidthfromtiptotip:18“-20”(455mm-510mm),foot
peg height: 12.5”-14.75” (320mm-375mm)). NOTE: Often trail bikes WITHOUT a folding shift lever will not t.
SPL01 Issue 1 12/12/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions Wear protective
gloves Wear safety
footwear Wear protective
clothing

4. INSTALLATION
4.1. INSTALLATION FOR TRANSPORTATION
4.1.1. When used for the transport of motorcycles, the base must be firmly bolted to the floor of a trailer or van.
4.1.2. If mounting to a trailer or other vehicle, ensure that the floor is strong enough to take the weight of the motorcycle/s plus the tie downs.
4.1.3. The tie down is secured to the base by means of the four wing bolts and spring washers. When using the chock for
transportation purposes, the front wheel of the motorcycle must be securely strapped to the tie down utilising the strap gap.
4.1.4. For additional security, consideration should also be given to securing the rear wheel as well.
5. OPERATION
5.1. To operate the unit, rotate the knobs into the lock position and simply roll or ride your bike into the trailer until your foot pegs hit the
open jaws of the SPL01.
5.2. Press down on the upper jaws and they will automatically lock into place.
5.3. Tighten the locking knob
5.4. To release your bike, simply rotate the knobs into the release position and step on the top jaws. This will automatically release the jaws
and free your motorcycle.
5.5. For additional safety, insert the attached locking pins prior to transport. You can replace the locking pins with padlocks for added
security and a theft deterrent.
SPL01 Issue 1 12/12/22
Original Language Version
© Jack Sealey Limited

6. MAINTENANCE
6.1. When the jaws are not in use, leave it in the open position.
6.2. Keep the jaws clean and wipe off any oil or grease.
6.3. Before each use check all parts. If any part of the tie down is damaged or defective, remove the tie down from service and take the
necessary action to remedy the problem.
SPL01 Issue 1 12/12/22
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers
and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
REGISTER YOUR
PURCHASE HERE