Sega 18 Wheeler User manual

ADDENDUM TO OWNERS MANUAL
MANUAL ADDENDUM: 999-0900
1st Printing: Feb 6, 2000
SEGA ENTERPRISES, INC. USA

Warranty
Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies
that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workman-
ship or materials under normal operating conditions. This also certifies that all Interactive Control
Assemblies are to be free from defects in workmanship and materials under normal operating condi-
tions. No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to
replace or repair the defective part during the warranty period. For Warranty claims, contact your
Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Ne-
glect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other dam-
ages.
This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other
warranties expressed or implied. Under no circumstance shall it extend beyond the period of time
listed above.

OPTIONAL DOLLAR BILL ACCEPTOR
THE COIN DOOR ASSEMBLY USED ON 18 WHEELER COMES
EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED
WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE
GAME FOR THIS APPLICATION.
THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING
VALIDATORS:
HOLE POSITION#1 Mars 2000 series
(UNIVERSAL MOUNTING POSITION) Cash Code DBV
The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series
upstacker. A 2000 series stacker can be added by simply removing the DBA entry plate and replacing it with Mars
stacker. This two entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The
part number is 40-3000-00. The Mars stacker can be obtained through an autherized Mars distibutor.

10 - 2 VOLUME ADJUSTMENT/REPLACEMENT
Volume adjustment/replacement should be performed after the HANDLE MECHA has been
removed as per 10 -1.
ADJUSTMENT
In order to turn the HANDLE SHAFT, insert the STEERING HANDLE to the HANDLE
SHAFT.
Secure the HANDLE at the centering position.
Loosen the 2 screws which secure the VOLUME BRACKET to push the gear out of mesh.
With the HANDLE SHAFT being the centering position, bring the gear into mesh so that the
status of the volume’s shaft is as shown in the Fig below.
Fasten the screws securing the VOLUME BRACKET.
After work is finished, perform volume setting in the Test Mode.
“D” CUT FACE (HANDLE SHAFT)
“D” CUT FACE (VOLUME)
SCREW (2)
M4x14, w/flat &
spring washers
REPLACE THIS PAGE (PAGE#56 in the ORIGINAL MAUAL)
1
2
3
4
5
6

MODIFICATIONS TO THE DESIGN RELATED PARTS

MODIFICATIONS TO THE PARTS LIST
For all US modified parts you will notice that on the corresponding
table it calls out LOCAL PURCHASE.
This is to mean that these items cannot be purchased through SEGA’ S SERVICE DEPARTMENT
and can be obtained at a local hardware store or a specialty store.
MODIFICATIONS TO PARTS ASSY #PTR-2500 (ASSY CHANGED TO PTR1-2500)
PART NOT LISTED OR SHOWN IN DRAWING #999-0901 Base Handle Reinforcement Brkt
Attached to Item #3 (Part No. PTR-2504 BASE HANDLE MECHA/NEW Part No. PTR1-2504)
IN ADDITION
Item #19 (Part No. SPG-2109 STOPPER RUBBER has been modified/ NEW Part No. SPG1-2109 )
These parts are used for extra support and are included in all US manufactured games.
PART NO. 999-0901
Base Handle reinforcement brkt.
MODIFICATIONS TO PARTS ASSY #PTR-1000 (ASSY CHANGED TO PTR1-1000)
PART NOT LISTED OR SHOWN IN DRAWING #999-0902 (2) Steering Reinforcement Brkt
Attached to a portion of the wooden cabinet, these brackets (one for each side) ensure that
force excerted upon the Steering Assy does not damage the wooden frame.
This part is used for extra support and is included in all US manufactured games.
PART NO. 999-0902 (qty. 2)
Steering reinforcement brkt.
(one for each side)

MODIFICATIONS TO PARTS ASSY #PTR-1000 (ASSY CHANGED TO PTR1-1000)
PART NOT LISTED OR SHOWN IN DRAWING #999-0903 (3) Steering Spoke Cover Upper
PART NOT LISTED OR SHOWN IN DRAWING #999-0904 (3) Steering Spoke Cover Lower
Attached to Item #32 (Part No. PTR-2501 STEERING HANDLE)
These parts are used for extra support/safety and are included in all US manufactured games.
Location of Spoke Covers
Steering Handle
MODIFICATIONS TO PARTS ASSY #PTR-1200 COIN DOOR ASSY
(ASSY CHANGED TO PTR1-1200)
OLD NUMBERS
ITEM NO. PART NO. DESCRIPTION
101 220-5237-91~ ASSY C.C. 2DR
220-5482-91~ ASSY C.C. 2DR
NEW NUMBERS
ITEM NO. PART NO. DESCRIPTION
101 40-3000-00 ASSY C.C. 2DR*
*See coin door insert on the following page for an exploded view of coor door assy.
(Prior to Part list Modifications.)
*This part can only be ordered through Happ Controls or a Happ Controls Distributor.

EXPLODED VIEW OF US COIN DOOR ASSY

MODIFICATIONS TO THE PARTS LIST (cont’d)
REPLACED HARDWARE COMPONENTS (screws, nuts, etc..)
SEAT COVER -TOP REAR
SCREW MS B0 M4X16 SC BT TMP (TOP)
SCREW MS CHM M4X20 SC BT TMP (BOTTOM)
CONTROL PANEL COVER
SCREW MS B0 M4X16 SC BT TMP
S/A REAR DOOR (W/LOCK)
VENT
SCREW MS B0 M4X16 SC BT TMP
VENT (SEAT CAB)
SCREW MS B0 M4X16 SC BT TMP
S/A MUFFLER PANEL (TO CAB)
SCREW MS B0 M6X30 SC BT TMP
S/A MUFFLER
SCREW MS CRM M4X12 SC BT TMP
(TOP / BOTTOM OF MUFFLER [4] )
(MUFFLER PNL [6] )
STEERING WHEEL
SCREW MS B0 SCREW M4X25 SC BT TMP
SEAT CUSHIONS
SCREW MS B0 M6X30 SC BT TMP
START BUTTON PLATE
SCREW MS CRM M4X12 SC BT TMP
HORN BUTTON PLATE
SCREW MS CRM M4X12 SC BT TMP
GRILLE-SEAT ACCESS SIDE
SCREW MS B0 M4X20 SC BT TMP
AC UNIT
SCREW MS B0 M4X20 SC BT TMP
GRILLE (BACK OF SEAT)
SCREW MS CRM M4X20 SWC BT TMP
COVER TOP-FRONT
SCREW MS B0 M4X20 SC BT TMP
COIN BOX MTG BRACKET
SCREW MS B0 M4X20 SC BT TMP
MARQUEE TO CABINET
SCREW MS B0 M5X55 SC BT TMP
CABINET FRONT TO MONITOR CAB
SCREW MS CRM M5X45 SC BT TMP
VENT
SCREW MS B0 M4X16 SC BT TP
MARQUEE COVER
SCREW MS CRM M4X20 SC BT TP
[1]
[3]
[3]
[1]
[11]
[1]
[2]
[8]
[2]
[8]
[2]
[18]
[2]
[20]
[1]
[4]
[2]
[10]
[1]
[4]
[1]
[4]
[2]
[8]
[1]
[4]
[1]
[12]
[4]
[4]
[1]
[4]
[1]
[4]
[1]
[4]
[1]
[4]
[1]
[5]
ITEM DESCRIPTION QTY.
NOTE: with regards to the items
detailed at left. Those that are
underlined are the assemblies that
the screws pertain to. The quanti-
ties of both the assemblies and the
screws are listed to the right of
each item in brackets.

VISIT OUR WEBSITE!