Sharp DX-C200 User manual

Read this manual carefully before you use the product and keep it handy for future refer-
ence. For safe and correct use, please be sure to read “Safety Information” before using
the machine.
Names and Locations
Using the Copier Function
Using the Scanner Function
Using the Fax Function
Troubleshooting
Removing Paper Jams
Quick Guide
Print Cartridges
DX-C200

2
Table of Contents
1
Names and Locations
Exterior• 3
Interior• 4
C• ontrol Panel 5
Initial Screen and Basic Operation• 7
Advanced Photocopy Settings• 9
Initial Screen and Basic Operation• 12
Advanced Scan Settings• 18
Initial Screen and Basic Operation for Sending a Fax • 19
Advanced Scan Settings• 22
Error and Status Messages on the Screen • 23
Printing or Scanning Problems• 27
Fax Transmission Problems• 28
Paper Jam Positions• 29
Removing from the Fusing Unit• 30
Removing from the Tray• 32
Removing from the Transfer Unit• 33
Removing from the ADF• 34
Before Replacing Print Cartridges• 37
Replacing Print Cartridges• 38
2
Using the Copier Function
3
Using the Scanner Function
4
Using the Fax Function
5
Troubleshooting
6
Removing Paper Jams
7
Print Cartridges

3
Names and Locations
Exterior
Output Tray for the ADF
Originals scanned with the ADF are
output here.
Output Tray/Top Cover
Printed paper is output here. Open here
to replace the print cartridges.
Front Cover
Open this cover to replace the waste
toner bottle or remove jammed paper.
USB Flash Disk Port
Insert a USB flash disk for using the Scan to USB function or
connect a digital camera using a USB cable for PictBridge
printing.
Tray 1
Tray 2 (option)
Control Panel
Input Tray for the ADF
Place stacks of originals here. They will feed in
automatically.
ADF (Auto document feeder)
Cover
Open this cover to remove originals jammed in
the ADF.
Exposure Glass
Open the cover and place originals here sheet
by sheet.

4
CES406
CES141 CES142
Names and Locations
Print Cartridges
Load from the machine rear, in the order of
cyan (C), magenta (M), yellow (Y), and
black (K).
Interior
Waste Toner Bottle
Collects excess toner during printing.
Transfer Unit
Remove this unit when replacing the waste
toner bottle.

5
Names and Locations
Control Panel
1Screen
Displays current status and messages.
2Scroll keys
Press to move the cursor in the direc-
tions indicated by each scroll key.
Pressing the [ ][ ] keys while the
machine is in standby mode will dis-
play the menu for configuring the set-
tings of the machine’s current opera-
tion mode (copier, scanner, or fax).
3Number keys
Use to enter numerical values when
specifying settings such as fax num-
bers and copy quantities, or enter let-
ters when specifying names.
4[Clear/Stop] key
• While the machine is processing a
job: press to cancel the current job.
• While configuring the machine: press
to cancel the current setting and re-
turn to standby mode.
• While in standby mode: press to
cancel temporary settings such as
the image density or resolution.
5[B&W Start] key
Press to scan or copy in black and
white, or start sending a fax.
6[Color Start] key
Press to scan or copy in color.
7[OK] key
Press to confirm settings or enter the
next level of the menu tree.
8[Escape] key
Press to cancel the last operation or
exit to the previous level of the menu
tree.
9Alert indicator
Flashes yellow when the machine will
require maintenance soon (such as
replacing consumables), or lights up
red when a machine error occurs.
When an alert is issued, check the
messages on the screen and follow
the instructions as provided in “Error
and Status Messages on the Screen”
on page 23.
10 Power indicator
Remains lit while the power is on. It is
unlit when the power is off.
11 Fax Received indicator
Lights up when received faxes that
have not been printed out exist in the
machine’s memory. Flashes when the
machine is unable to print out the fax-
es due to machine errors such as an
empty paper tray or a paper jam.
CES403
12345
67891011

6
Names and Locations
Control Panel
1One Touch buttons
Press to select a scan or fax Quic
k
Dial destination.
2[Address Book] key
Press to select a scan or fax destina-
tion from the Address Book.
3[On Hook Dial] key
Press to use on-hook dialing to chec
k
the destination’s status when sending
a fax.
4[User Tools] key
Press to display the menu for configur-
ing the machine’s system settings.
5[Image Quality] key
Press to select scan quality for the
current copy, scan, or fax job.
6[ID Card Copy] key
Press to enter ID card copy mode for
the current job.
7[Copy]/[Facsimile]/
[Scanner] key
Press to switch the machine’s opera-
tion mode.
8Selection keys
Press the key that corresponds to an
item shown on the bottom line of the
screen to select it.
9[Density] key
Press to adjust image density for the
current copy, scan, or fax job.
10 [Reduce/Enlarge] key
Press to specify the reduction/en-
largement ratio for the current copy
job, or the document size for the cur-
rent scan job.
11 [Pause/Redial] key
Press to insert a pause in a fax number,
or display the last used scan or fax
destination.
12 [Shift] key
Press to switch between Quick Dial
numbers 1 to 10 and 11 to 20 when
specifying a scan or fax destination
using the One Touch buttons.
CES404
2534 61
891011
7
12

7
Using the Copier Function
Initial Screen and Basic Operation
The following is the initial screen in copier mode.
1. Current status or messages
2. Current settings
3. Selection key items
If function names appear here,
press a corresponding selec-
tion key to use that function.
4. Copy quantity
The original in the ADF takes precedence over the original on the exposure glass if you•
place originals both in the ADF and on the exposure glass.
Press the [Copy] key.
CES174
Place the original face down on the exposure glass or face
up in the ADF.
Lift the ADF carefully without holding the input tray. Otherwise, the ADF
might be damaged.
Exposure Glass ADF
CES070 CES109
If necessary, configure advanced photocopy settings. For more details, see “Advanced Pho-•
tocopy Settings” on page 9.
CES250
[] 14
1
3
2

8
Using the Copier Function
To make multiple copies, enter the number of copies using
the number keys
The maximum number of copies is 99.•
Press the [B&W Start] or [Color
Start] key.
CES169
To cancel photocopying, press the [Copy] key, press the [Clear/Stop] key, and then press•
[Yes] for confirmation.
You can change the paper tray for the current job by pressing the [• ][ ] keys. If tray 2
is installed, you can select to change the paper tray automatically according to the paper
size (A4 or Letter).
If a paper jam occurs, printing stops after the current page has been printed out. After the•
jammed paper is removed, printing restarts from the jammed page automatically.
If a scanning jam occurs in the ADF, copying is canceled immediately. In this case, copy the•
originals again starting from the jammed page.
For information about originals, see “Getting Started”,• User Guide.
For information about removing jammed paper, see “Removing Paper Jams” on page 29.•
Initial Screen and Basic Operation

9
Using the Copier Function
❖Making Enlarged or Reduced Copies
You can specify the reduction or enlargement ratio for the current job. There are two
ways to set the scaling ratio: using a preset ratio or manually specifying a custom
ratio.
Press the [Reduce/Enlarge] key.1.
Press [Reduce] or [Enlarge], press the [2. ][ ][ ][ ] keys to select the desired ratio,
and then press the [OK] key.
If [Zoom] has been selected, specify the desired ratio using the number keys, and then3.
press the [OK] key.
❖Copying Multiple Pages onto One Sheet
This function is only available when the original is set in the ADF, not when it is set on the•
exposure glass.
To use this function, the paper size used for printing copies must be set to A4, Letter, or Legal.•
You can set 2-in-1/4-in-1 copy mode for the current job.
Press the [Reduce/Enlarge] key.1.
Press [Reduce], press the [2. ][ ][ ][ ] keys to select [Comb. 2 on 1] or [Comb. 4
on 1].
Press the [3. ][ ] keys to select the desired printout format, and then press the [OK]
key.
The following types of printout format can be selected depending on your preference.
Printout formats for 2-in-1 copying
[Portrait] [Landscape]
CES033 CES034
Printout formats for 4-in-1 copying
[Portrait: L to R] (Left to Right) [Landscape: L to R] (Left to Right)
CES035
CES037
[Portrait: T to B] (Top to Bottom) [Landscape: T to B] (Top to Bottom)
CES036 CES038
Advanced Photocopy Settings

10
CES125
CES126
CES127
CES128
Using the Copier Function
❖Making 2-sided Copies
This function is only available when the original is set in the ADF, not when it is set on the•
exposure glass.
Paper must be fed from tray 1 or tray 2, not from the bypass tray. In addition, paper size must•
be A4, B5, Letter, Legal, Executive, 8" x 13", 8 1/2" x 13", Folio, or 16K, and paper type must
be thin, plain, middle thick, recycled, color, preprinted or prepunched.
You can set the machine to copy in 2-sided copy mode.
Press the [Copy] key.1.
Press the [2. ][ ] keys.
Press the [3. ][ ] keys to select [2 Side Copy], and then press the [OK] key.
Press the [4. ][ ] keys to select the printout format, and then press the [OK] key.
Press the [User Tools] key to return to the initial screen.5.
“2 Sided Copy” appears on the display, indicating that the machine is now in 2-sided
copy mode.
The following types of printout format can be selected depending on your prefer-
ence.
Printout formats for Top-to-Top copying
[Top to Top ] [Top to Top ]
Printout formats for Top-to-Bottom copying
[Top to Bottom ] [Top to Bottom ]
After this function is set, all subsequent copies will be 2-sided, unless you cancel the setting•
by selecting [Off] for [2 Side Copy].
Advanced Photocopy Settings