ShoreStation SSV20100EDC User manual

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 1 REV B 03/09/2009
SSV20100EDC & SSV20100EDCDW
SSV20100EDC Hoist Alum SS V-Frame - EDC
69423 Hardware Box - SSV20100 Hoist
62421 Lower Frame Bundle - V20100
62423 Platform Bundle - V20100
6941601 Winch Assembly - DC 2000 & 4000 lb Hoist
65582 Winch Tube Bundle - V20100
62926 Leg Bundle - V20100
HA0020 Bunk Poly V15/20100
HA0061 Battery Box / Brkt Mech. Winch Tube
69585 Lit Packet, V20100EDC/DW
NOTE: When referencing the front of hoist, this represents the winch end. When referencing the hoist end, this represents opposite of the
winch end. Winch side is also referred to the right side of the hoist.
SSV20100EDCDW Hoist Alum SS V-Frame - EDCDW
69423 Hardware Box - SSV20100 Hoist
62421 Lower Frame Bundle - V20100
62423 Platform Bundle - V20100
6941601 Winch Assembly - DC 2000 & 4000 lb Hoist
65582 Winch Tube Bundle - V20100
67228 Leg Bundle - V15/20100 DW
HA0020 Bunk Poly V15/20100
HA0061 Battery Box / Brkt Mech. Winch Tube
69585 Lit Packet, V20100EDC/DW

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 2 REV B 03/09/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 3 REV B 03/09/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 4 REV B 03/09/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 5 REV B 03/09/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 6 REV B 03/09/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 7 REV B 03/09/2009
Winch Post Guide Posts
Lower Frame Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 8 REV B 03/09/2009
Platform Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 9 REV B 03/09/2009
Winch Tube Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 10 REV B 03/09/2009
DC Drive Winch Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 11 REV B 03/09/2009
Battery Box

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 12 REV B 03/09/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 13 REV B 03/09/2009
DW (Deep Water) SECTION:
The deep water version of this boat hoist is assembled
using the same assembly instructions as the standard
hoist. The only items that are different between the two
hoists are the length of the upright corner posts and the
adjustable legs inside them as identied in the drawings
for deep water legs.
The water depth where your hoist is going to be installed
will determine whether you should use the deep water
version of this hoist.
The deep water version of this hoist can be used in deep-
er water depths because of the additional length of the
extension legs. Listed below is the amount of adjustment
the various legs have.
• A standard leg shipped with the hoist has 20” of
adjustment.
• The deep water legs have 55” of adjustment.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 29 REV B 03/09/2009
BATTERY SPECIFICATIONS
The speed at which the load can be raised is direct-
ly proportional to the power available to do the job.
The larger and better the batteries are that power the
winch system, the more satised you will be with the
results obtained when using a DC powered winch.
ShoreStation recommends that the battery used to power
the winch system is a deep cycle battery Group 24 minimum.
The following are items you can do to help with the perfor-
mance.
• Make sure the battery is fully charged.
• A solar panel that generates 20 amps or more is
recommended to keep the battery fully charged in a eld
situation.
• A battery maintainer can be used if 110 volt power
source is available to operate the maintainer. A battery
maintainer that will supply a minimum of 6 amps and
12 volts is recommended to properly maintain a battery.
12/24V DC CONNECTIONS
It is very important that the terminals and ground connec-
tions are clean, and tightened sufciently to make an excel-
lent contact. Clean connections with a wire brush to make a
positive connection.
Make sure all cable connections are connected to the proper
terminals.
OPERATING PROCEDURES
Connect the system battery cables in the following congu-
rations:
Figure A – 12VDC Battery Conguration
Figure B – 24VDC Battery Conguration
Figure C – Optional 24VDC Battery Conguration
Figure D – Optional 24VDC Battery Conguration
KEYBOARD OPERATION
To enable the keypad function, enter the factory or user-de-
ned 4 digit code. The preset factory code is the sequence
“1-2-3-4”.
The numbers entered into the keypad do not have to be
changed if numbers are entered by mistake. The only re-
quirement is that the four digit sequence of numbers be en-
tered into the system during the number entering process.
Do not press the code button anytime before or after the
code is entered into the system. Doing so will disable
the keyboard so the keyboard functions will not oper-
ate.
When you start entering numbers onto the keypad, the
GREEN - LED light will light up. When the correct sequence
of four numbers is entered into the system anytime during
the number entering process, the RED- LED will light up.
Once the RED - LED is lit, the UP, DOWN, and LIGHT func-
tion keys on the keypad will operate. The remote controls
are disabled when the RED - LED is lit.
Once the keypad has been activated using the sequence
numbers as just described, the keyboard will stay activated
for approximately 2 minutes. It will then return to an inactive
mode.
Pressing the code button will activate the remote con-
trol and disable the keypad at the same time. The key-
pad and remote control can never be operated at the
same time.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003787
PAGE 32 REV B 03/09/2009
4811504
Max Load
Decal - Winch
Assembly
4811312
Clamp Arrow Decal
4811319
Adj. Gauge Decal
4811502
Safety Operating Decal
4850408
Not A Step Decal
4850363
Safety Decal
4850408
Not A Step
Decal
4811312
Clamp Arrow Decal
4811319
Adj. Guage Decal
SSV20100EDC Decal Placement
4811504 Maximum Load Decal - Winch Assy
4811502 Safety Operating Decal
4811312 Clamp Arrow Decal
4811319 Adj. Gauge Decal
4850363 Safety Decal
4850408 Not A Step Decal