Siemens CX70 Instruction Manual

CX70
Emoty
Issued by
Information and Communication mobile
Haidenauplatz 1
D-81667 Munich
© Siemens AG 2004
All rights reserved. Subject to availability.
Rights of modification reserved.
Siemens Aktiengesellschaft
www.siemens-mobile.com/cx70emoty
s
mobile
s
mobile
Designed for life
BA Cover CX70Emoty.QXD 25.08.2004 11:00 Uhr Seite 1

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\overview.fm
3Overview (en)
VAR Language: en; VAR issue date: 040728
left page (3) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Overview (en)
1
3
4
5
7
6
2
Emoty
Info ìOptions
1Emoty device. The Emoty device is fit-
ted like a CLIPIt™ cover, p. 7.
2Studs for opening the Emoty cover,
p. 8.
3Emoty start screen. This appears
when the Emoty application has
started, p. 10.
4Emoty sensors. You can control the
intensity and expression of the ani-
mated figure with the three built-in
sensors. The stroking and pressing
sensors are on the sides. The shaking
sensor is built into in the CLIPIt™
cover, p. 10.
5Display buttons
6Joystick. You can use the joystick Ito
select a figure (p. 10).
7Emotion keys 0- 9.
Use these buttons to select the emo-
tions that you would like to send
(p. 12). The emotion keys only
become active after you have started
the Emoty application.
This user handbook uses the same sym-
bols and menu guidance as those shown
in the user handbook of your mobile tele-
phone.

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\emoIVZ.fm
4 Table of Contents
VAR Language: en; VAR issue date: 040728
left page (4) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 07:22)
Table of Contents
Overview (en) ............................ 3
Table of Contents ....................... 4
Introduction ............................... 5
Welcome ................................. 5
Safety precautions ................... 5
Getting started ........................... 7
Installing Emoty on your
telephone ................................ 7
Disassembling your
telephone ............................ 7
Install Emoty ........................ 7
Uninstalling the Emoty ......... 8
Software installation ................ 9
Download ............................ 9
Upload from a PC ................. 9
Using Emoty ............................. 10
Start Emoty ............................ 10
Ending Emoty ........................ 10
Creating emotions ................. 10
Select a figure with
the joystick ......................... 10
Assigning an emotion ......... 11
Changing the emotion ........ 11
The fun button ................... 12
Sending emotions by MMS .....12
Sending emotions ............... 13
Send display ....................... 13
Adding text ......................... 14
Saving text ......................... 14
Resetting the emotion ........ 15
Changing the resolution
of the animation ................. 15
Setup ........................................ 16
Downloading new figures ....... 16
Downloading new emotions ...16
Deleting a figure/emotion ....... 16
Adjusting and testing sensor
settings .................................. 17
Dynamic Light .................... 17
Appendix .................................. 18
Self help for problems ............ 18
Customer Care ....................... 18
Care and maintenance ............ 19
Battery quality declaration ......19
Display quality declaration ......19
Technical data .................... 20
Operating times .................. 20
Guarantee certificate (UK) ...... 20
Guarantee certificate (IRL) ...... 21
SAR – European Union (RTTE) . 22
SAR – International (ICNIRP) ... 23
Table of
Contents

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\Einführung.fm
5Introduction
VAR Language: en; VAR issue date: 040728
left page (5) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Introduction
Welcome
Your Emoty lets you express your
emotions in a completely new way
and send them immediately by MMS
to your friends and acquaintances.
• Choose one of three figures,
p. 10.
• Choose one of 10 different emo-
tions, p. 11.
• Show your feelings to the figure
by pressing, stroking or shaking
your telephone, p. 11.
• Add a text and send the emotion
immediately by MMS, p. 12.
• Download new figures from the
Internet, p. 16.
Safety precautions
Information for parents
Please read the operating instructions and
safety precautions carefully before use.
Explain the content to your children and the
hazards associated with using the phone.
Remember to comply with
legal requirements and local
restrictions when using the
phone. For example in aero-
planes, petrol stations, hospi-
tals or while driving.
Mobile phones can interfere
with the functioning of medical
devices such as hearing aids
or pacemakers. Keep at least
20 cm/ 9 inches between
phone and pacemaker. When
using the mobile phone hold it
to the ear which is further away
from the pacemaker. For more
information consult your
doctor.
Message tones are repro-
duced through the loud-
speaker. Do not hold the
telephone to your ear when it
rings. Otherwise you risk seri-
ous permanent damage to
your hearing.

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\Einführung.fm
Introduction6
VAR Language: en; VAR issue date: 040728
left page (6) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Only use original Siemens bat-
teries (100% mercury-free)
and charging devices. Other-
wise you risk serious damage
to health and property: the bat-
tery could explode, for
instance.
You may only open the phone
to replace the battery, face-
plate, keypad or SIM card. You
must not open the battery
under any circumstances. Any
other changes to this device
are strictly prohibited and will
invalidate the operating
licence.
Important
Dispose of used batteries and
phones according to the legal
regulations.
Mobile phones can interfere
with the operation of nearby
TVs, radios or PCs.
Use only Siemens original
accessories. This will avoid
potential risks to health or
property and ensure compli-
ance with all relevant
regulations.
Improper use will invalidate the guarantee!
These safety instructions also apply to Sie-
mens original accessories.

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\montage.fm
7Getting started
VAR Language: en; VAR issue date: 040728
left page (7) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Getting started
Installing Emoty on your
telephone
If you have a CX70 Emoty, you only
need to insert the SIM card and fit
the Emoty cover before you can "get
going" (p. 10)!
If you have a separate CX70 Emoty
cover, you need to install the Emoty
application and Emoty animations
on your telephone as well, p. 9.
Before fitting the Emoty cover, switch
your telephone off!
Disassembling your telephone
• If necessary, disassemble your tel-
ephone according to the instruc-
tions in the user handbook of your
telephone.
• Remove the old keypad.
Install Emoty
Insert the telephone in the lower shell
1Hold the telephone with the display
facing upwards.
Insert the lower edge of the telephone
at an angle into the lower shell of the
Emoty cover.
Make sure that the telephone is inserted
under the contact pin of the Emoty!
2Carefully press on the upper shell of
the telephone until it clicks into place
in the lower shell.
Place the new keypad on the tele-
phone. Make sure that it is seated cor-
rectly.
Emoty keyboard
The new keyboard lets you select Emotions
by pressing the symbols (p. 11). If the
Emoty application is switched off, the key-
board functions like your normal telephone
keyboard.

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\montage.fm
Getting started8
VAR Language: en; VAR issue date: 040728
left page (8) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Fitting the upper shell Uninstalling the Emoty
Remove the upper shell of the
Emoty cover
Removing the telephone
1Insert the stud on the bottom of the
upper shell into the corresponding
recess of the Emoty lower shell.
2Carefully press on the upper shell until
it clicks into place.
Note
Please check that all sides of the upper
shell have clicked correctly into place.
1Press on the side studs (p. 3) until the
upper shell springs open.
2Pull the upper shell forwards at an
angle and remove it.
Tilt the lower shell forwards and take
out the telephone. You can carefully
tap the lower shell against your hand
so that the telephone comes out
gently.

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\montage.fm
9Getting started
VAR Language: en; VAR issue date: 040728
left page (9) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Software installation
If you upgrade one of the telephones
of the CX70 series to Emoty, you
must first install the Emoty applica-
tion with the animations on your
telephone.
Requirement: Your telephone must
have an Emoty hardware interface.
Please ask your dealer for details.
Download
C¢O¢Applications
ISelect Emoty.
CStart the browser.
Or
C¢O¢Internet
§Options§ Open menu.
Go to... Select and enter
wap.siemens-
mobile.com/emoty.
CStart the download.
Upload from a PC
You can load the software from a PC
to the telephone.
The software necessary for this is
available on the enclosed CD. You
can install it on the telephone from
your PC.
Further information about the instal-
lation is available on the Internet
under www.siemens.com/
cx70emoty.
Requirements
• The telephone is switched on.
• You have connected your tele-
phone to your PC via the data
cable or via the IrDA interface.
Installation
• Insert the CD in the CD drive of
your PC.
• Start the Mobile Phone Manager
(Requirement: The program is
installed).
• Copy the Emoty folder and all its
contents from the CD onto the
telephone.
Further information is available on
the CD or on the Internet under
www.siemens.com/
cx70emoty.
You must then disconnect the tele-
phone from your PC.
Now you can start the Emoty appli-
cation on the telephone. Require-
ment: You have already fitted the
Emoty cover (p. 7)
Note
If you have any questions or problems
about the software installation, please con-
tact our customer service, p. 18.

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\starting.fm
Using Emoty10
VAR Language: en; VAR issue date: 040728
left page (10) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Using Emoty
The user handbook uses the same
symbols and menu guidance as
those shown in the user handbook
of your mobile telephone.
Start Emoty
If you have fitted the Emoty cover on
your telephone, there are two ways
of starting Emoty.
Either:
§Emoty§ Press this display button.
If this display button is not yet
assigned to the Emoty application,
you must change the assignment
first. For details of how to do this,
read the user handbook of your tele-
phone.
Or:
Start the Emoty application via the
Surf & Fun menu of your telephone.
C¢O¢Applications
¢Emoty
Emoty is started.
Ending Emoty
§Options§ Open menu.
Exit Select this function.
§Yes§ Emoty is ended.
§No§ Process is stopped.
Creating emotions
Select a figure with the joystick
After you have started Emoty, the
start display appears. A figure is
already selected. If you like it, you
can assign it your emotions (p. 11).
If you want to select another figure:
ISelect a figure.
Under each figure, the emotions
which can be selected are high-
lighted.
You can, however, also download
new figures and/or emotions (p. 16).
Note
The Emoty application must be installed
(p. 9).
Emoty
Info íOptions

©
Siemens AG 2003, W:\ICM_MP_CCQ_S_UM\04FL00717 CX70 Emoty Thai und NL\Work\emoty_Latin_mit_leerseiten\frame_en\starting.fm
11Using Emoty
VAR Language: en; VAR issue date: 040728
left page (11) of CX70 EMOTY en, A31008-H7101-A703-3-TM19 (06.12.2004, 09:22)
Assigning an emotion
You can now assign an emotion to
the selected figure. You can choose
between the following emotions:
Press one of the buttons 0to 9
to assign this emotion to your figure.
After selecting an emotion the
selected figure displays this emotion
and can only be changed by you.
Changing the emotion
Your Emoty cover has three sensors
which can be used to change the
emotion of your figure:
•Pressing. Press on the left or right
sensor (p. 3).
•Stroking. Stroke the left or right
sensor (p. 3).
•Shaking the telephone.
Effects of positive emotions
If you have selected one of the posi-
tive emotions 1to 5, this
means:
•Stroking a sensor strengthens the
emotion
•Pressing a sensor weakens the
emotion
Note
The last figure you selected is automatically
loaded when the Emoty application is
restarted.
Icon/button Emotion
1Love
2Happy
3Curious
4Surprise
5Apology
6Naughty
7Boredom
8Sad
9Anger
0Fun
Note
You can adjust the sensitivity of the sen-
sors, p. 17.