Siemens MKB-1 User manual

Siemens BuildingSiemens Building
Siemens BuildingSiemens Building
Siemens Building
TT
TT
Tecec
ecec
echnologieshnologies
hnologieshnologies
hnologies
Fire SFire S
Fire SFire S
Fire Safetyafety
afetyafety
afety
INTRODUCTION When the MXL Keyboard/Display Panel is installed in a control panel, the compo-
nents are behind a locked door. Unlock and open the door to gain access to the keys
and controls.
THE DISPLAY The ¼ VGA display allows the user to view up to 8 lines of events and 1 complete
system status line at the same time. The ninth line of the screen is a fixed line that is
located below the 8 listed events that are visible, and holds the highest priority
unACKowledged event. What is shown on the display depends on the current state
of the System.
If your system is set for Canada, the
oldest event appears in the first line
of the display.
If your system is set for the United
States, the most recent event
appears in the first line of the
display.
Line 10 contains the system status
information which is grouped by
event type.
Lines 11 and 12 normally display the
System messages, date and time.
This area on the display functions
like the MKB-1/-2/-3/-4 two-line
display. Press ENTER to activate the
MXL menu options.
Lines 13, 14 and 15 are used to
display more information on a
particular event when the user
presses the MORE INFO key.
The System has several displays.
When the System is first powered
on it displays a screen similar to the
one shown in Figure 1.
Local Mode Operation
Operating Instructions
MXL Multi-Line Keyboard/Display Panel
P/N 315-048692-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SIEMENS FIRE SAFETY
APP : RX.X.X
Example shown is Canadian Display
Figure 1
MXL Keyboard/Display in Start-up Mode

Siemens Building Technologies
Fire Safety
P/N 315-048692-22
All examples in this document are given for the Canadian display.
When the system is in Normal mode, the display is similar to the one shown in
Figure 2.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SIEMENS BUILDING TECHNOLOGIES
Example shown is Canadian Display
12:22:22 Oct 22, 02
ALR=000, SUP=000, TBL=000, SEC=000
(000 / 000)
Figure 2
MXL Multi-Line Display in Normal Mode
When events are annunciated, the system goes into Active mode. The display for
Active mode is similar to the one shown in Figure 3.
After 90 seconds of panel inactivity, (i.e., no additonal incoming events or user
interface activity), the screen will change and display the oldest event for Canada
and the most recent event for the United States in the first line.
When the system is set for the United States, there may appear to be a delay in the
reporting of events.This is because the most recent event is placed at the top of the
event list. It might be necessary to scroll to the top of the list to view the most
recent event.

Siemens Building Technologies
Fire Safety
P/N 315-048692-23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SIEMENS BUILDING TECHNOLOGIES
TBL BELL #1 (IAC 1) (main)
TBL INPUT LOOP 2, DEVICE #1
TBL INPUT LOOP 2, DEVICE #4
TBL INPUT LOOP 2, DEVICE #5
TBL INPUT LOOP 2, DEVICE #6
TBL INPUT LOOP 2, DEVICE #7
TBL INPUT LOOP 2, DEVICE #8
TBL INPUT LOOP 2, DEVICE #2
IN
IN
IN
IN
IN
IN ACK
OUT ACK
IN
Example shown is Canadian Display
12:22:22 October 22, 02
ALR=000, SUP=000, TBL=017, SEC=001
TBL BELL #1 (IAC 1) (main) IN
2-001 Audible Loop
007 Signal Circuit Loop Open
21:22:22 Oct 21, 01
40 Characters
Highlight
Custom
Message
ACK
Status
Highest Priority
Unacknowledged
Event
System Status
Line
Current
Time/Date
Device Type
TBL Type
Event
Time/Date
System
Message
Queue
Event #
Event
Type
Event
Address
(007 / 018)
Event #
Total # of Events
Figure 3
MXL Multi-Line Display in Active Mode
As an example, when a trouble event is annunciated the System places the event on
the display according to its priority or queue (Alarm, Supervisory,Trouble, then
Security) in the format: [Event Type] [Custom Message] [IN/OUT] [ACK STATUS or
BLANK].The system status in line 10 is also updated to reflect the newest event.
ACK appears in the display if the event has been acknowledged; otherwise, the field
is blank. IN is displayed when an event occurs; OUT is displayed when a normal
state is restored.
To view information about a previous event, press the UP () or DOWN () keys
located next to the MORE INFO key to scroll to the desired event and highlight it,
then press the MORE INFO key. Lines 13, 14 and 15 will display the event informa-
tion in the following format:
[event address] [device type]
[event number in queue] [event type]
[event time/date] [event number in all queues] [total number of events]

Siemens Building Technologies
Fire Safety
P/N 315-048692-24
DISPLAY KEYS The Multi-Line Display has three display keys, UP (), DOWN () and MORE INFO,
which are located on the MKB, as shown in Figure 4.
Press the DOWN key to scroll down the items in the list one event at a time.The
DOWN key only works when scrolling the first eight lines of the display, it does not
scroll to the fixed event on line nine.This key enables the user to view the list of
events that are off-screen. The screen will stop moving down once the end of the list
is reached.
Press the UP to scroll back up to the top of the list of events.The UP key only works
when scrolling the first eight lines of the display, it does not scroll to the fixed event
on line nine. This key enables the user to view the list of events that are off-screen.
The screen will stop moving up once the top of the list is reached.
Press the MORE INFO key after highlighting an event using the UP and DOWN keys
to display the basic event information on the screen, including the event number,
address, time/date, and device type or trouble type. When used together with the
numerical keypad, the MORE INFO key can be used to jump to the top of any event
queue. For example, to reach the first event in the Alarm queue, press and hold
MORE INFO and then press 1 on the numeric keypad. (1= Alarm, 2=Supervisory,
3=Trouble, 4=Security.)
ACC
SURV.
SUPV
ACK
ALIMENTATION
ACK
ALARME
ALARM
ACC
SIL
SIL
AUD
AUD
HORS SERVICE
SYSTÈME
PARTIELLEMENT
DISABLED
PARTIAL SYSTEM
`
POWER
RÉENCL.
ACC
ACK
ACC
PANNE
TRBL
ACK
SEC
SEC
RESET
ALT 1
FONCTION
FUNCTION/
FONCTION
FUNCTION/
ALT 2
FUNCTION/
FONCTION
MORE
INFO
PLUS
D'INFO
4
*
7
PQRS
GHI
8 9
0#
5
TUV
JKL
6
WXYZ
MNO
1 2
ABC
3
DEF
ALT
ENTRER
ENTER/
EFFACER
CLEAR/
SPACE/
ESPACE
PRINT/
IMP.
ALT
2
F4
1
F3
F2
AIDE
HELP/
F1
Figure 4
The MKB Keyboard/Multi-Line Display Panel
(Canadian Model is Shown Here)

Siemens Building Technologies
Fire Safety
P/N 315-048692-25
System Control Keys The System Control Keypad is described in the table below:
DAPYEKLORTNOCMETSYS
yeKesopruP
KCAMRALAmralaerifaegdelwonkcaoT
LISDUAtiucricecnailppanoitacifitonaecnelisnuroecnelisoT
KCAVPUSyrosivrepusaegdelwonkcaoT
KCALBRTelbuortaegdelwonkcaoT
KCACESnoitidnocytirucesaegdelwonkcaoT
OFNIEROM rehtegotdesunehW.tnevenatuobanoitamrofnillaweivoT
otpmujnacrotarepoeht,)4,3,2,1(dapyeklaciremunehthtiw
tsrifehthcaerot,elpmaxeroF.eueuqtneveynafopoteht
OFNIEROMnwoddlohdnasserp,eueuqytiruceSehtnitneve
.dapyekehtno4sserpdna
TESERmetsySehtteseroT
System Control LEDs When lit, the LEDs (light-emitting diodes) indicate the conditions described in the
following table:
SDELLORTNOCMETSYS
DELsetacidnI
MRALAerifdegdelwonkcanuenotsaelasierehtnehwsehsalF
erasmralaerifllanehwylidaetsswolg;mrala
.degdelwonkca
DECNELISSELBIDUA noitacifitonenotsaeltanehwsehsalf,smetsys.S.UroF
llanehwylidaetsswolg;evitcasi)CAN(tiucricecnailppa
decneliserasCANelbaecnelistesersimetsyslitnuroF.
eraselbiduanehwnosnrutylno,smetsysnaidanaC
.decnelis
YROSIVREPUSdegdelwonkcanuenotsaeltasierehtnehwsehsalF
eraseirosivrepusllanehwylidaetsswolg;yrosivrepus
.degdelwonkca
ELBUORT ;elbuortdegdelwonkcanuenotsaeltasierehtnehwsehsalF
.degelwonkcaeraselbuortllanehwylidaetsswolg
YTIRUCESdegdelwonkcanuenotsaeltasierehtnehwsehsalF
ytirucesllanehwylidaetsswolg;noitidnocytiruces
.degdelwonkcaerasnoitidnoc
REWOP.nosirewopehtsetacidnI
.rewopCA=wolgydaetS
.pukcabyrettab=nOgnihsalF
METSYSLAITRAP
ELBASID
.delbasidsiecivedenotsaeltA

Siemens Building Technologies
Fire Safety
P/N 315-048692-26
Addresses All modules and devices annunciated on the MXL are identified by an address
(MMM-DDD). Each address is in two parts: a module address (MMM) and a device
address (DDD).The number identifying the module may be as high as 253, and the
number identifying the device may be as high as 254. Enter all leading zeros for
module and device addresses or use the SPACE key to eliminate the need to enter
the leading zeros. For events specific to a module, the device address is not required.
Fixed Addresses A module may be assigned to any address on the System, except for some fixed
addresses that have already been assigned. (See the Fixed Module Addresses Table.)
The modules communicate to the MXL Control Panel through a serial communica-
tions network called MNET.The System continuously supervises all of the modules
for presence and proper operation.You may assign a module to any address on the
System, and assign addresses in any order, mixing different types of modules and
leaving gaps in the numbering, provided you do not use the fixed addresses.
SESSERDDAELUDOMDEXIF
eludoM
sserddA
eludoMeciveD
sserddA
)egnaR(
0esUtoNoD
1)2-/1-BMM(1poolgolanA060-100
2)2-/1-BMM(2poolgolanA060-100
3
⇓
842BKM
942BKM
052BKM
1521.oN,BKM
252devreseR
3522-/1-)BMS(BMM052ot100
452M-GSCremmargorP
552)devreser(labolG
The following modules occupy an address on the System, but have no devices (and
no device addresses).
• MKB • NET-7 • RCC-1/-2/-3 • RCC-1F/-2F/-3F
• CMI-300 • RCM-1 • NIM-1W/-1R
Numeric Keypad Use the numeric keypad (keys 0 through 9) when the System asks for a module
number, device number, password, time, date, or other information. The display
shows each number as you press the key (except when you enter a password the
System shows an asterisk for each digit that you type).

Siemens Building Technologies
Fire Safety
P/N 315-048692-27
Command Keypad The command keys are described in the following table:
DAPYEKDNAMMOC
yeKesopruP
×
nognihsalfsitahwfotfelehtotmetiehttceleS
.)rebmunagniretnesselnu(yalpsideht
Ø
nognihsalfsitahwfothgirehtotmetiehttceleS
.)rebmunagniretnesselnu(yalpsideht
Ù
.metisuoiverpehtotkcaboG
RETNE
sirosrucehthcihwnometiehttcelesotsserP
otRETNEsserp,srebmunnignipytretfA.gnihsalf
.yrtneehtetelpmoc
PLEH
.egassemenil-enoayalpsidotsserP
TNIRP
.stroperdnastsilsuoiravgnitnirpnigebotsserP
ECAPS
elpitlum"0"tupniotdeenehtetanimileotsserP
,010-100sserddaehttupniot,elpmaxeroF.semit
.RETNEdnaECAPS01ECAPS1retne
RAELC
gnisserpybnugebstuotnirplecnacotsserP
:tnirplliwmetsySehT.TNIRP
.detanimretylerutamerpgnitsilsihT
The ALT and Function Keys Using the four function keys alone or in combination with ALT1 or ALT2 provides a
total of 12 special functions. When using a combination, hold the ALT key down and
then press the function key.
F1 ALT1+F1 ALT2+F1
F2 ALT1+F2 ALT2+F2
F3 ALT1+F3 ALT2+F3
F4 ALT1+F4 ALT2+F4
These keys are defined using the CSG-M Custom Software Generator (See the
CSG-M Programming Manual, P/N 315-090381).
Internal Audible Alarm The internal audible alarm sounds steadily when there is an unacknowledged alarm.
It pulses if all alarms are acknowledged but there is at least one supervisory, trouble,
or security condition.
PRINT and CLEAR Keys If your System includes the printer option, the printer automatically prints System
events. Either an external serial or parallel printer can be connected.To select the
printer port, refer to the CSG-M Programming Manual, P/N 315-090381.
The multi-line display cannot be connected to aTSP-40 strip printer.
The PRINT key is used to print various lists and reports. To cancel the printing at any
time, press the CLEAR key; the System will print the following message:
This listing prematurely terminated.

Siemens Building Technologies
Fire Safety
P/N 315-048692-28
Modes Of Operation The MXL alphanumeric display annunciator has five modes of operation:
1. Alarm
2. Supervisory
3. Trouble
4. Security
5. Normal
This order ensures that alarms always take priority over all other conditions. In turn,
supervisories always take priority over troubles and troubles always take priority over
security conditions. All of the above modes take priority over Normal mode.
Normal Mode Normal mode is the absence of any alarms, supervisories, troubles, or security
conditions.
In Normal mode, the display will look similar to the one shown in Figure 2 on page 2.
The POWER LED glows steadily in Normal mode when the System has AC power.
The ALARM, AUDIBLE SILENCE, SUPERVISORY,TROUBLE, SECURITY, and
PARTIAL SYSTEM DISABLE LEDs are off and the internal audible is off.
If your System has the printer option, the System prints a message in the following
format every day at midnight, even when there are alarms or other conditions:
System Status at 00:00:00 Oct 02, 20xx
0 ALARM 0 ALARM ACK
0 SUPERV 0 SUPERV ACK
0 TROUBLE 0 TROUBLE ACK
0 SECURITY 0 SECURITY ACK
Alarm Responding to an Alarm
Follow the response plan approved by the local authority having jurisdiction.
When the MKB is installed, the ACKnowledge key and audible Alarm Silencing key
(AUD SIL) on the MKB are behind a locked door. To acknowledge an alarm or trouble,
or to silence an audible alarm, first unlock and open the door.
Alarm Annunciation When a fire is detected, the System causes the ALARM LED on the MKB to flash,
the System’s internal audible to sound and the display on the MKB to display the
event in the format shown in Figure 5. When the country setting is US, the AUDIBLE
SILENCE LED flashes.

Siemens Building Technologies
Fire Safety
P/N 315-048692-29
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SIEMENS BUILDING TECHNOLOGIES
ALM CUSTOM MESSAGE
ALM CUSTOM MESSAGE
IN
IN
Example shown is Canadian Display
12:01:01 Dec 31, 02
ALR=002, SUP=000, TBL=000, SEC=000
ALM CUSTOM MESSAGE IN
40 Characters
ACK
1-001 ID-60I Ionization Detector
002
11:59:59 Dec 31, 02 (002 / 002)
Figure 5
ALARM Event Screen With More Info Key Pressed
In addition, the System responds to alarms with programmed output functions such
as other audible signals.
In Figure 5, 1-001 represents the address of the device reporting the alarm. On the
display, not all leading zeros are shown. If your System includes a printer, note that
the leading zeros are not shown. 002 on Line 14 in the More Info area (Lines 13-15)
tells you that this is the second (and the most recent) of two alarms received.The
status information shown in Line 10 reports the total number of alarms, supervisories,
troubles, and security conditions.

Siemens Building Technologies
Fire Safety
P/N 315-048692-210
If your System includes a printer, it prints a message from two to four lines long
similar to the following:
ALARM 1-1 11:59:59 Dec 31, 2 xx
#2 [custom message], [device type]
In the above printed message, ALARM indicates that the type of event is an alarm;
1-1 is the device address; #2 is the number of the alarm in the list of alarms; [cus-
tom message] is a custom message entered using the CSG-M Custom Software
Generator (See the CSG-M Programming Manual, P/N 315-090381); [device type] is
the type of device which reported the alarm.
Viewing the List of Alarms To see the alarm list when there are more than eight alarms, press the DOWN key on
the MKB. (If your system is set for Canada, the system displays the oldest alarm
first.)
How to Individually Acknowledge an Alarm (NFPA 72 Proprietary, UL 1076)
• The first unACKnowledged alarm is placed on line nine of the display. Press
ALARM ACK to acknowledge the alarm. The System acknowledges the first
alarm displayed and then places the second unACKowledged alarm in line
nine (the fixed line). If your System has the printer option, it prints an alarm
acknowledgment message similar to the following:
ACK Alarm 1-5 12: 1:28 Dec 31,2 xx
#2 [custom message], [device type]
Note that the acknowledgment message includes the term ACK to indicate
this alarm was acknowledged.
• Continue acknowledging alarms as explained above until the System
displays the following message on Line 11:
ALL ALARMS ACKNOWLEDGED
The ALARM LED glows steadily to indicate that all alarms are acknowl-
edged. If there are no supervisories, troubles, or security conditions still in
the System, the internal audible goes silent; if any of those conditions still
exist, the internal audible pulses.
• If your System includes a printer, it prints a message similar to the following:
ACK Alarm 12: 5:44 Dec 31,2 xx
All Alarms Are Now Acknowledged.