Silhouette Infinity View 1600 Owner's manual

Infinity View
Technical
Instructions
Models 1600, 2937, 2938, 2939
V-Bevel Edging

Infinity View | Glazing with Silhouette Vision Sensation®
Lenses
Silhouette now offers premium prescription lenses for all
Silhouette frames.
Expertly crafted in Austria using our exclusive
Panorama®lens designs, Silhouette Vision Sensation®
lenses perfectly match the curve of every Silhouette
frame.
This results in a 100% Silhouette eyewear solution that
offers the wearer exceptional visual comfort and edge to
edge clarity.
For more information visit:
https://www.silhouette.com/us/us/vision-sensation or
contact your Silhouette Account Executive

Mount temples on frame front using BLS 58 sleeve and Silhouette mounting plier
with turquoise or blue tip.
Infinity View | Temple Mounting

Infinity View | Glazing
Frame is designed with a 5.0 base curve, however other base curves will work
Lenses with base curves flatter than 5.0 should have V-bevel cut to match 5.0 base
curve
Recommended lenses are High Index 1.6, 1.67, Polycarbonate and Trivex
OMA shape files available at
https://portal.silhouette.com
www.silhouettelab.com

Infinity View | Cold Glazing
TECHNICAL INFORMATION INFINITY VIEW5
Cold insert lenses in all Infinity View frames!
Do not heat the frame under any circumstance!
Lenses that are too large will need to be resized!
Always insert lenses from the back of the frame!

Infinity View| Lens Insertion V-Bevel Fullrim
TECHNICAL INFORMATION INFINITY VIEW6
1. Insert the lens from the rear, starting with the nasal corner.
2. Continue inserting the lens along the top to the temporal corner.
3. Continue around the lens circumference until the lens snaps into
place.

Infinity View | Lens Removal
TECHNICAL INFORMATION INFINITY VIEW7
1. At the bottom of the frame, partially push frame back and
separate the frame from the lens
2. Push lens out of frame toward the front

Inclination | Infinity View
1. Open the temple.
2. Support the temple mount with the Silhouette mounting pliers.
3. Incline the temple at the endpiece in the desired direction.
TECHNICAL INFORMATION INFINITY VIEW8

Infintity View | Temple Opening Increase
TECHNICAL INFORMATION INFINITY VIEW9
1. Open the temple.
2. Support the temple mounting with Silhouette mounting pliers.
3. Press the temple out at the endpiece with thumb or index finger.

Infinity View | Temple Opening Decrease
TECHNICAL INFORMATION INFINITY VIEW10
1. Open the temple.
2. Support the temple mounting with Silhouette mounting pliers.
3. Press the temple in at the endpiece with thumb or index finger..

Infinity View | Temple Bend Adjustment
TECHNICAL INFORMATION INFINITY VIEW11
1. Adjust the temple to the ear shape with large curves.
2. Temple can be heated to aid adjustment.
3. During temple-end adjusting do not put pressure on the temple tip.

Infinity View| Temple Shortening - Glued
TECHNICAL INFORMATION INFINITY VIEW12
1. Straighten the end of the temple.
2. Break the adhesive bond by squeezing
with with double-jaw padded pliers.
3. Carefully pull off the temple end.
4. Shorten titanium wire with metal-
diagonal cutter.
5. File down sharp edges and burrs.

Infinity View| Temple Shortening - Glued
TECHNICAL INFORMATION INFINITY VIEW13
6. Gently remove
remaining glue.
7. Cut plastic temple end to required
length with sharp blade in the
original angle.

Infinity View| Temple Shortening - Glued
TECHNICAL INFORMATION INFINITY VIEW14
8. Reinstall temple cover.
9. Apply a small amount of glue on the inside of the titanium wire as shown.
10.Slide the temple cover fully onto the titanium wire, wipe off excess glue.

Infinity View | Temple Removal
TECHNICAL INFORMATION INFINITY VIEW15
1. Close the temple and hold the lens mount with your thumb and index
finger.
2. Using other hand, pull the temple off from the endpiece in direction shown
by red arrow.

Infinity View | Temple Install
TECHNICAL INFORMATION INFINITY VIEW16
1. Support the frame front as shown.
2. With the temple in the closed position, align the temple to the hinge
elements on the endpiece with the temple slots
3. Press temple onto the endpiece

Infinity View | Teflon Lubricant
After cleaning the frame in an ultrasonic bath,
relubricate the hinge with Teflon.
TECHNICAL INFORMATION INFINITY VIEW17

Additional information | Infinity View
Cleaning in an ultrasonic bath or with ethanol is possible.
Avoid high temperatures such as the dashboard in the car or the
sauna.
Always use the supplied case for storage.
TECHNICAL INFORMATION INFINITY VIEW18

19