Silvercrest SFKS 2 B1 User manual

WIRELESS DOORBELL SFKS 2 B1
IAN 279882
WIRELESS DOORBELL
Operating instructions
TRÅDLÖS DÖRRKLOCKA
Bruksanvisning
FUNKTÜRKLINGEL
Bedienungsanleitung
OVIKELLO
Käyttöohje
BELAIDIS DURŲ
SKAMBUTIS
Naudojimo instrukcija

GB Operating instructions Page 1
FI Käyttöohje Sivu 25
SE Bruksanvisning Sidan 49
LT Naudojimo instrukcija Puslapis 73
DE/AT/CH Bedienungsanleitung Seite 99
Before reading, unfold the page containing the illustrations
and familiarise yourself with all functions of the device.
Käännä ennen lukemista kuvallinen sivu esiin ja tutustu
seuraavaksi laitteen kaikkiin toimintoihin.
Vik ut bildsidan och ha den till hands när du läser igenom
anvisningarna och gör dig bekant med apparatens/maski-
nens funktioner.
Prieš skaitydami atsiverskite lapą su paveikslėliais ir susipa-
žinkite su visomis prietaiso funkcijomis.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen
aus und machen Sie sich anschließend mit allen Funktionen
des Gerätes vertraut.

A
C
B
5x 2x 2x

SFKS 2 B1 GB │ 1 ■
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Warnings used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Basic safety guidelines . . . . . . . . . . . . . . . . . . . . . . . . .5
Descriptions of components . . . . . . . . . . . . . .9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Check the package contents . . . . . . . . . . . . . . . . . . .10
Disposal of packaging materials. . . . . . . . . . . . . . . . .11
Power supply: receiver . . . . . . . . . . . . . . . . . . . . . . . .11
Inserting/replacing the batteries. . . . . . . . . . . . . . . . .11
Handling and operation . . . . . . . . . . . . . . . .13
Selecting the signal type. . . . . . . . . . . . . . . . . . . . . . .13
Adjusting the signal sound volume . . . . . . . . . . . . . . .13
Selecting the ringer melody . . . . . . . . . . . . . . . . . . . .14
Synchronising the sender and receiver . . . . . . . . . . . .14
Mounting the transmitter . . . . . . . . . . . . . . . . . . . . . .15
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . .16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .16
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Storage when not in use. . . . . . . . . . . . . . . .18
IB_279882_SFKS2B1_LB3.indb 1 29.08.16 13:27

SFKS 2 B1
■ 2 │ GB
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Disposal of the appliance . . . . . . . . . . . . . . . . . . . . . .18
Disposal of batteries . . . . . . . . . . . . . . . . . . . . . . . . . .19
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Notes on the Declaration of Conformity. . . . . . . . . . .20
Kompernass Handels GmbH warranty. . . . . . . . . . . .21
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
IB_279882_SFKS2B1_LB3.indb 2 29.08.16 13:27

SFKS 2 B1 GB │ 3 ■
Introduction
Congratulations on the purchase of your new
appliance.
You have selected a high-quality product. The oper-
ating instructions are part of this product. They contain
important information on safety, usage and disposal.
Before using the product, familiarise yourself with
all handling and safety guidelines. Use the product
only as described and for the range of applications
specified. Keep these operating instructions in a safe
place. Please also pass these operating instructions
on to any future owner.
Intended use
This appliance serves as a wireless doorbell system
to announce visitors, allowing for the operation of
a door bell without any wiring. The appliance is not
intended for any other purpose, nor for use beyond
the scope described. The appliance is not intended
for use in commercial or industrial environments. The
manufacturer accepts no responsibility for damage
caused by failure to observe these instructions,
improper use or repairs, unauthorised modifications
or the use of unapproved replacement parts. The risk
shall be borne solely by the user.
IB_279882_SFKS2B1_LB3.indb 3 29.08.16 13:27

SFKS 2 B1
■ 4 │ GB
Warnings used
The following warning notice types are used in
these operating instructions:
DANGER
A warning notice at this hazard level
indicates an imminently hazardous
situation.
If the hazardous situation is not avoided, it could
result in death or serious physical injury.
► Follow the instructions in this warning notice to
avoid the risk of death or serious injury.
CAUTION!
A warning notice at this hazard level
indicates a potential for property dam-
age.
Failure to avoid this situation could result in prop-
erty damage.
► Follow the instructions in this warning notice to
prevent property damage.
NOTE
► A note provides additional information that will
assist you in using the appliance.
IB_279882_SFKS2B1_LB3.indb 4 29.08.16 13:27

SFKS 2 B1 GB │ 5 ■
Safety
This section contains important safety instructions for
using the appliance. This appliance complies with
statutory safety regulations. Improper use may result
in personal injury and property damage.
Basic safety guidelines
■ This appliance may be used by children aged
8 years and above and by persons with limited
physical, sensory or mental capabilities, or lack
of experience and knowledge, provided that
they are under supervision or have been told how
to use the appliance safely and are aware of the
potential risks. Children must not use the appli-
ance as a plaything. Cleaning and user mainte-
nance tasks may not be carried out by children
unless they are supervised.
■ The mains plug is used as a separator from the
electricity grid and must always be readily ac-
cessible.
■ Risk of explosion if the battery is replaced incor-
rectly. Replace only with the same or equivalent
type.
■ Do not place any sources of naked flames, such
as lighted candles, on the appliance.
IB_279882_SFKS2B1_LB3.indb 5 29.08.16 13:27

SFKS 2 B1
■ 6 │ GB
■ Check the appliance for visible external damage
before use. Do not operate an appliance that
has been damaged or dropped.
■ Do not expose the appliance to direct sunlight
or high temperatures. Otherwise it may overheat
and be irreparably damaged.
■ Do not expose the receiver to water spray or
drips, and do not place liquid-filled objects such
as vases or open drink containers on or near the
receiver.
■ Warning: electrical voltage!
Never open the housing of the receiver. There
are no user-serviceable or replaceable compo-
nents inside the appliance.
■ Do not make any unauthorised modifications or
alterations to the appliance.
■ All repairs must be carried out by authorised
specialist companies or by the Customer Service
department. Improper repairs may put the user at
risk. It will also invalidate any warranty claims.
■ Unplug the appliance immediately if you smell
burning or notice smoke. Have the appliance
checked by a qualified specialist before using it
again.
IB_279882_SFKS2B1_LB3.indb 6 29.08.16 13:27

SFKS 2 B1 GB │ 7 ■
DANGER
Mishandling the batteries can cause fires,
explosions, leakages or other hazards!
In order to handle batteries safely, please
observe the following safety instructions:
► Do not throw the batteries into a fire and do not
subject them to high temperatures.
► Do not open, deform or short-circuit batteries,
since this can lead to chemical leakage.
► Do not attempt to recharge the batteries.
► Check the condition of the batteries at regular
intervals. Leaking chemicals can cause permanent
damage to the appliance. Take particular care
when handling damaged or leaking batteries.
Risk of acid burns! Wear protective gloves.
► Chemicals that leak from a battery can cause
skin irritation. In the event of contact with the
skin, rinse with plenty of water. If the chemicals
come into contact with your eyes, rinse thorough-
ly with water, do not rub and consult a doctor
immediately.
► Keep batteries out of the reach of children.
Children might put batteries into their mouth and
swallow them. If a battery has been swallowed,
seek medical assistance IMMEDIATELY.
IB_279882_SFKS2B1_LB3.indb 7 29.08.16 13:27

SFKS 2 B1
■ 8 │ GB
DANGER
► Always insert the batteries the right way round
(observe correct polarity) otherwise there is a
danger that they could explode.
► If you do not intend to use the appliance for a
long time, remove the batteries.
► Do not ingest the battery – there is a risk of
chemical burns!
► This product contains a button cell battery.
Swallowing the button cell battery can cause
severe internal burns in just 2 hours and can lead
to death.
► Keep new and old batteries away from children.
► If the battery compartment does not close
securely, stop using the product and keep it away
from children.
DANGER
Do not allow children to play with the packaging
material! Keep all packaging materials out of the
reach of children. Risk of suffocation!
IB_279882_SFKS2B1_LB3.indb 8 29.08.16 13:27

SFKS 2 B1 GB │ 9 ■
Descriptions of components
(See fold-out page for illustrations)
Receiver (Fig. A)
1Speaker
2Signal display
3Signal type switch (optical/acoustic)
4Volume button (VOL)
5Melody selection button
6Synchronisation button
Sender (Fig. B)
7Nameplate cover
8Ringer button
9Battery compartment
0Battery compartment cover
q Mounting plate
Accessories (Fig. C)
wDouble-sided adhesive tape
eName plate
r Wall plug
t Screw
z 3V battery, type CR2032
IB_279882_SFKS2B1_LB3.indb 9 29.08.16 13:27

SFKS 2 B1
■ 10 │ GB
Operation
Check the package contents
(See fold-out page for illustrations)
The scope of delivery includes the following compo-
nents:
● 1 x receiver
● 1 x sender
● 1 x 3V battery, type CR2032
● 5 x name plates
● 2 x wall plugs with screws for sender assembly
● 1 x double-sided adhesive tape
● These operating instructions
♦ Remove all parts of the appliance from the pack-
aging and remove all packaging materials.
♦ Check the package for completeness and for
signs of visible damage.
♦ If the delivery is incomplete or damage has
occurred as a result of defective packaging or
during transport, contact the Service hotline (see
chapter entitled Service).
IB_279882_SFKS2B1_LB3.indb 10 29.08.16 13:27

SFKS 2 B1 GB │ 11 ■
Disposal of packaging materials
The packaging protects the appliance from damage
during transport. The packaging materials have
been selected for their environmental friendliness
and ease of disposal, and are therefore recyclable.
Returning the packaging into the material
cycle conserves raw materials and
reduces the amount of waste generated.
Dispose of packaging materials that are no longer
needed in accordance with applicable local regu-
lations.
Power supply: receiver
The receiver is plugged into a properly installed
mains power outlet and does not require batteries.
Inserting/replacing the batteries
♦ Detach the mounting plate qfrom the transmitter.
♦ Grip the battery compartment cover 0on both
tabs and pull it off.
♦ Insert a 3V battery, type CR 2032, into the
battery compartment 9. The side of the battery
marked with a “+” must be facing upwards.
IB_279882_SFKS2B1_LB3.indb 11 29.08.16 13:27

SFKS 2 B1
■ 12 │ GB
♦ Slide the battery compartment cover 0back
onto the battery compartment 9until it clicks
into place. Ensure that the sealing ring is
properly inserted into the frame of the battery
compartment 9. Otherwise, IP protection is not
provided.
♦ To reattach the mounting plate q to the transmit-
ter, hook one side of the transmitter into the gap
of the mounting plate q , then push the transmit-
ter downwards until it clicks into place.
NOTE
► If the performance of appliance reduces or com-
pletely stops, it means the battery is exhausted.
Replace the used battery with a new one of the
same type.
IB_279882_SFKS2B1_LB3.indb 12 29.08.16 13:27

SFKS 2 B1 GB │ 13 ■
Handling and operation
Selecting the signal type
The receiver can indicate the reception of a door-
ring signal either optically, acoustically, or optically
and acoustically.
♦ To select, move the signal type switch 3to the
desired position:
— acoustic ringer signal only, the selected
melody will be played
— optical ringer signal only, the signal
display flashes
— optical and acoustic ringer signal
Adjusting the signal sound volume
Press the VOL button 4 repeatedly until the desired
volume is set.
Loud Medium Quiet
IB_279882_SFKS2B1_LB3.indb 13 29.08.16 13:27

SFKS 2 B1
■ 14 │ GB
Selecting the ringer melody
There are 36 different ringer melodies stored in the
appliance.
♦ Press the melody select button 5.
♦ Stop the selection when you hear the desired
melody. The appliance will use the last-played
melody.
NOTE
► If you remove the receiver from the mains socket,
the set melody remains saved for approximately
40 seconds. After this time, you need to set your
desired melody anew.
Synchronising the sender and receiver
The transmitter and receiver of this wireless doorbell
system can communicate with each other via a num-
ber of different codings. This means that you can
operate up to 5 transmitters with one receiver. In ad-
dition, you can extend the wireless doorbell system
with any number of receivers. This is only possible if
the sender and receiver within a system are working
on the same frequency, however. For this, you must
synchronise the appliances as follows:
♦ Press the synchronisation button 6on the
receiver.
♦ Now press the ringer button 8on the transmitter.
IB_279882_SFKS2B1_LB3.indb 14 29.08.16 13:27

SFKS 2 B1 GB │ 15 ■
If the synchronisation has been a success, the
receiver notifies you of the programmed call signal.
Should the receiver not react as described, repeat the
synchronisation.
Mounting the transmitter
♦ Select a suitable positioning for the sender, close
to your outer door.
♦ Mark the positions for the required drill holes
with the help of the mounting plate qand drill
the holes for the supplied wall plugs r(6mm
drill).
♦ Push the wall plugs into the drill holes and screw
the mounting plate q onto the wall using the
screws t.
♦ Push the transmitter onto the mounting plate q
until it clicks audibly into place.
NOTE
► Alternatively, you can mount the transmitter
onto a suitable surface using the double-sided
adhesive tape w.
♦ Label one of the supplied name plates e. If you
label the name plate by hand, make sure you
use a waterproof pen.
IB_279882_SFKS2B1_LB3.indb 15 29.08.16 13:27

SFKS 2 B1
■ 16 │ GB
♦ Remove the name plate cover 7from the trans-
mitter and insert your name plate into the recess
on the transmitter.
♦ Replace the name plate cover 7on the trans-
mitter.
Maintenance
The appliance is maintenance-free. No form of
maintenance, either on or in the appliance, is
intended for execution by the user. In the event of
malfunction or apparent damage, contact Customer
Services. If the appliance is not going to be used for
an extended period, remove the batteries.
Troubleshooting
There is no ring when pressing the ringer
button
♦ Check whether there is a battery (type CR2032)
in the transmitter.
♦ Check whether the power outlet being used for
the receiver is working properly.
♦ It is possible that the transmitter is not synchro-
nised with the receiver. Repeat the synchronisa-
tion.
♦ Ensure that the signal type switch is set to the
position or .
IB_279882_SFKS2B1_LB3.indb 16 29.08.16 13:27

SFKS 2 B1 GB │ 17 ■
The range is reduced
♦ A weak battery will reduce the range. Change
the battery every 12–18 months.
♦ Metal constructions, walls, ceilings or other ap-
pliances that use the same frequency can affect
the range. Try to avoid mounting the transmitter
in the immediate vicinity of any metal parts.
NOTE
► If you cannot solve the problem with the
above-mentioned solutions, please contact the
Service Hotline (see chapter entitled Service).
Cleaning
CAUTION!
► There are no serviceable parts or parts requiring
cleaning inside the appliance. Moisture can
cause damage to the appliance.
► Do not use caustic, abrasive or solvent-based
cleaning materials. These can damage the surfac-
es of the appliance.
♦ Clean the housing of the appliance with a lightly
moistened cloth and a mild detergent only.
IB_279882_SFKS2B1_LB3.indb 17 29.08.16 13:27