Sinoboom 1414E Plus User manual

1414E Plus/4655E Plus
for Sinoboom Poland
Maintenance
Manual
Part No.PL501063110002
Rev: A
Jun 2022
GTJZ
0608E (2132E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
长沙市宁乡高新技术产业园区金洲大道东
128 号
0731-87116111 hr@sinoboom . c om . cn ww w .sinoboom . c om . cn
Al w ays F or B e t t er A cc ess Solution s
我们一直在追求新的高 度
尺寸 ：
210×285mm
20mm
20mm
产品说明书
PRODU C T MAN U AL

Operating, servicing and maintaining this vehicle or
equipment can expose you to chemicals including engine
exhaust, carbon monoxide, phthalates, and lead, which
are known to the State of California to cause cancer and
birth defects or other reproductive harm. To minimize
exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your vehicle or equipment in
a well-ventilated area and wear gloves or wash your
hands frequently when servicing. For more information
go to: www.P65warnings.ca.gov.
For disposal, please follow your nation regulation.

Please contact us:
Website : www.sinoboom.com
E-mail : [email protected]
Sales Tel : [phone]
Service Tel : [phone]
Address : No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha,
Hunan, China
Zip Code : 410600
Copyright © Hunan Sinoboom Intelligent Equipment CO.,Ltd. All Rights Reserved
The final interpretation right of this manual belongs to Hunan Sinoboom Intelligent Equipment CO.,Ltd.
Manual revision history:
REV DATE DESCRIPTION REMARK
AJun, 2022 Original issue of the manual

APPLICATION
Use the following table to identify the specific serial number for
models included in this manual. Check the model of your machine before
consulting the manual, and then use the correct manual according to the
serial number of the model. See the nameplate on your machine to
identify the model and serial number. (See Decals/Nameplates
Inspection of the Operation Manual for details.)
MODELS
Trade identification
SERIAL NO.
Metric Imperial
1414E Plus 1414E Plus 4655E Plus CE: From PL0107000100 to Present
ANSI/CSA: From PL0106300100 to Present
NOTE:
•Product model is applied in product nameplate for distinction of products of different main
parameters.
•Product trade identification is applied in marketing and machine decals for distinction of products of
different main parameters, and can be classified as metric type and imperial type: The metric type of
trade identification is applicable to machines for countries/regions using metric system or as
specially required by customers; The imperial type of trade identification is applicable to the
machines for countries/regions using imperial system or as specially required by customers.

This Page Intentionally Left Blank

STATEMENTS
Hunan Sinoboom Intelligent Equipment Co., Ltd. (Hereinafter referred to as Sinoboom) will upload the
latest product manual information to the website www. sinoboom. com as soon as possible. However,
due to continuous product improvement, the information in this manual is subject to change without prior
notice.
This manual covers the basic parts information of one or more products. Therefore, please use this
manual according to your needs. If you find problems in the manual or have suggestions for improve-
ment, feel free to share your feedback with Sinoboom, and we will address these issues as soon as
possible.
Feel free to consult and download the Operation Manual,Maintenance Manual and Parts Manual of the
products you need online at www.sinoboom.com.
Hunan Sinoboom Intelligent Equipment Co., Ltd. retains the right of final interpretation of the manual.
All of the above are registered trademarks of Hunan Si-
noboom Intelligent Equipment Co., Ltd..

This Page Intentionally Left Blank

1414E Plus Maintenance Manual i© Jun 2022
TABLE OF CONTENTS
Introduction ..............................v
1 Safety............................... 1-1
Safety Definitions . . . . . . . . . . . . . . . .. . . . . 1-1
Reporting Accidents. . . . . . . . . . . . . . . . . . . 1-1
Electrocution Hazards. . . . . . . . . . . . . . . . . 1-2
Tipping Hazards and Rated Load . . . . . 1-2
Work Environment Hazards . . . . . . . . . . . 1-4
Unsafe Operation Hazards. . . . . . .. . . . . 1-5
FallHazards...........................1-6
Collision Hazards . . . . . . . . . . . . . . . . . . . . . 1-7
Crush Hazards . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Explosion and Fire Hazards. . . . . .. . . . . 1-8
Damaged Machine Hazards . . . . . . . . . . 1-8
Bodily Injury Hazards . . . . . . . . . . . . . . . . . 1-9
Battery Hazards . . . . . . . . . . . . . . . . . . . . . . . 1-9
Welding and Polishing Requirements1-10
After Using the Machine. . . . . . . . . . . . . . 1-11
2 Specifications .................... 2-1
Machine Specifications . . . . . . . . . . . . . . . 2-1
Major Component Weights. . . . . . . . . . . . 2-3
Power System Specifications . . . . . . . . . 2-4
Hydraulic Hose and Fitting
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Hydraulic Hose Torque . . . . . . . . . . . . . 2-5
Hydraulic Fitting Torque . . . . . . . . . . . . 2-5
Hydraulic Hose and Fitting Torque
Procedure ..........................2-8
Fastener Torque Specifications . . . . . . . 2-8
3 System Descriptions............ 3-1
Power Source . . . . . . . . . . . . .. . . . . . . . . . . . 3-1
Hydraulic System . . . . . . . . . . . . . . . . . . . . . 3-1
Electrical System. . . . . . . . . . . . . . . . . . . . . . 3-1
Machine Control System . . . . . . . . .. . . . . 3-1
Safety Measures . . . . . . . . . . . . . . . . . . . . . . 3-1
4 Service and Guidelines......... 4-1
Machine Preparation, Inspection and
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
General.............................4-1
Preparation, inspection and
maintenance . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Qualified Sinoboom equipment
mechanic ...........................4-1
Pre-operation inspection. . . . . . . . . . . . 4-1
Pre-delivery inspection and
frequent inspection . . . . . . . . . . . . . . . . . 4-1
Annual machine inspection . . . . . . . . . 4-1
Preventive maintenance . . . . . . . . . . . . 4-2
Storage .............................4-3
Maintenance and Servicing
Precautions ...........................4-3
General.............................4-3
Safety and workmanship . . . . . . . . . . . 4-3
Cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Component removal and installation4-4
Component disassembly and
assembly ...........................4-4
Scrap of structural parts . . . . . . . . . . . . 4-4
Pressure-fit parts . . . . . . . . . . . . . . . . . . . 4-5
Bearings ............................4-5
Gaskets.............................4-5
Bolt usage and torque application . . 4-5
Hydraulic lines and electrical wiring 4-5
Hydraulic system . . . . . . . . . . . . . . . . . . . 4-5
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Battery..............................4-5
Pins and composite bearing. . . . . . . . . . . 4-5
Application of Insulating Silicone
Grease to Electrical Connections . . . . . 4-6
5 Maintenance ...................... 5-1

© Jun 2022 ii 1414E Plus Maintenance Manual
Conducting a Pre-delivery Inspection . 5-1
Following a Maintenance Schedule . . . 5-2
Completing a Repair & Inspection
Report.................................5-2
Checklist A Procedures . . . . . . . . . . . . . . . 5-4
A-1 Inspect All Manuals. . . . . . . . . . . . . 5-4
A-2 Inspect All Decals . . . . . . . . . . . . . . 5-5
A-3 Inspect Damaged, Loose or
LostParts...........................5-5
A-4 Inspect Hydraulic Oil Level . . . . . 5-5
A-5 Inspect Hydraulic Oil Leakage. . 5-6
A-6 Functional Tests . . . . . . . . . . . . . . . . 5-6
A-7 Inspect the Battery Level . . . . . . . 5-8
A-8 Perform Maintenance After 30
Days................................5-8
Checklist B Procedures . . . . . . . . . . . . . . . 5-8
B-1 Inspect Electric Wires . . . . . . . . . . 5-8
B-2 Inspect Rim, Tire and Fasteners5-9
B-3 Inspect Battery . . . . . . . . . . . . . . . .5-10
B-4 Inspect Hydraulic Oil . . . . . . . . . . 5-11
B-5 Inspect Air filter of Hydraulic
Tank ...............................5-11
B-6 Inspect Brake Manual Release
Function ...........................5-12
B-7 Inspect Emergency Lowering .5-13
B-8 Inspect Braking Device . . . . . . . .5-13
B-9 Test Lift/Lower Speed . . . . . . . . .5-14
B-10 Test Drive Speed. . . . . . . . . . . . .5-14
B-11 Inspect Tilt Protection . . . . . . . .5-15
B-12 Inspect Pothole Guards . .. . . .5-16
Checklist C Procedures . . . . . . . . . . . . . .5-16
C-1 Replace Hydraulic Oil Tank Air
Filter ...............................5-16
C-2 Inspect Platform Weighing
System (optional) . . . . . . .. . . . . . . . . . .5-16
C-3 Inspect Lift Limit Switch . . . . . . .5-17
C-4 Inspect Staged Lowering . . . . . .5-17
C-5 Inspect Carbon Brush of Motor5-17
Checklist D Procedures . . . . . . . . . . . . . .5-18
D-1 Inspect Scissor Arm Installation
Bearing ............................5-18
D-2 Inspect Chassis Slider . . . . . . . .5-18
D-3 Replace Hydraulic Oil Tank
Return Oil Filter Element . . . . . . . . . .5-18
D-4 Replace Hydraulic Oil . . . . . . . . .5-19
6 Repair............................... 6-1
Platform Components . . . . . . . . . . . . . . . . . 6-1
Platform Controller. . . . . . . . . . . . . . . . . . 6-1
Removing the Platform . . . . . . . . . . . . . 6-1
Removing the Extension Platform . . 6-2
Scissor Components . . . . . . . . . . . . . . . . . . 6-2
Scissor Assembly. . . . . . . . . . . . . . . . . . . 6-2
Removing the Lift Cylinder. . . . . . . . . . 6-3
Chassis Components . . . . . . . . . . . . . . . . . 6-3
Tires and Rims. . . . . . . . . . . . . . . . . . . . . . 6-3
Reducer & Drive Motor . . . . . . . . . . . . . 6-4
Removing the Front Wheel Bracket 6-5
Steer Cylinder . . . . . . . . . . . . . . . . . . . . . . 6-5
Battery..............................6-7
Hydraulic System . . . . . . . . . . . . . . . . . . . . . 6-7
Layout of Hydraulic Elements. . . . . . . 6-7
Removing the Hydraulic Valves. . . . . 6-8
Regulating the Hydraulic Valve
Pressure...........................6-13
Adjusting the Emergency Lowering
Handle.............................6-14
Hydraulic Symbols . . . . . . . . . . . . . . . . .6-15
Hydraulic Schematic . . . . . . . . . . . . . . .6-16
Electrical System. . . . . . . . . . . . . . . . . . . . .6-17
Use and Maintenance of Battery. . .6-17
Charger Troubleshooting . . . . . . . . . .6-19
Sinoboom Control System . . . . . . . . .6-20
DTC-K500 Control System . . . . . . . .6-26
Trouble Diagnosis . . . . . . . . . . . . . . . . .6-30
Fundamental Troubleshooting . . . . .6-40
Electrical Symbols . . . . . . . . . . . . . . . . .6-43
Electrical Schematic Diagram . . . . .6-45

1414E Plus Maintenance Manual iii © Jun 2022
Appendix 1: Prepare the Work
Record Before Delivery ....... A-1
Appendix 2：Repair & Inspection
Report .............................A-3

© Jun 2022 iv 1414E Plus Maintenance Manual

1414E Plus Maintenance Manual v© Jun 2022
INTRODUCTION
Thank you for choosing and using the machinery of
Hunan Sinoboom Intelligent Equipment Co., Ltd. Al-
ways read, understand and become familiar with the
operation requirements of the machine and its associ-
ated safety procedures before operating, maintaining
and repairing the machine. Operating the machine with-
out becoming familiar with its specific operation require-
ments and safety procedures poses serious risks.
Operators who follow safety rules and operate the ma-
chine carefully and effectively will prevent personal in-
jury, property loss and accidents.
Use this machine only to transport tools to work loca-
tions and for performing tasks on the work platform. Op-
erators must be competent and must obtain training to
carefully use the machine and follow safety procedures.
Only trained and authorized personnel may operate the
machine.
This manual guides the operator in operating and using
the machine. The operator is responsible for reading,
understanding and implementing the operation and
safety procedures in this manual and for following the
manufacturer’s instructions before beginning any work.
Read, understand and follow all safety rules and oper-
ating instructions. The operator must also consider the
machine’s uses and limitations and the conditions at
the jobsite before using this machine. Strictly following
all safety requirements in this manual is critical.
Consider this manual a part of the machine, along with
Maintenance Manual and Parts Manual, and always
keep the manuals with the machine. The owner or ad-
ministrator of the machine shall offer all manuals and
other necessary information provided by the machine
manufacturer regarding the daily inspection and main-
tenance to each of the renters. If the machine is sold,
the owner or administrator must pass along the man-
uals and other necessary information to the purchaser.
The owner or administrator of the machine shall also
provide the manufacturer’s maintenance information to
the person responsible for maintaining the machine.
If you have any questions, contact Hunan Sinoboom In-
telligent Equipment Co., Ltd..

© Jun 2022 vi 1414E Plus Maintenance Manual
This Page Intentionally Left Blank

1414E Plus Maintenance Manual 1-1 © Jun 2022
1SAFETY
Read, understand and comply with the safety rules and
regulations of your workplace and your government.
Before using the machine, ensure the operator is prop-
erly trained and qualified in safely operating the ma-
chine. The training includes but is not limited to：
•Warning and instruction decals on the machine
•Pre-operation inspection
•Any factors that may affect the machine stability
•Common hazards and countermeasures
•Jobsite inspection
•Functions of all controls and associated knowledge,
including emergency control.
•Personal protection equipment that suits the task,
workplace and environment.
•Safety operation
•Transporting the machine
•Measures against unauthorized use
•Operating instructions
Understand that as the operator you have the responsi-
bility and right to shut down the machine in case of fail-
ure with the machine or other emergency at your
workplace.
NOTICE
People suffering from heart disease, hypertension,
epilepsy and other diseases and people who fear
heights must never operate or use this machine. Al-
so, people who have alcohol or drugs in their system,
or experience excessive fatigue or depression, are
prohibited from operating or using this machine.
SAFETY DEFINITIONS
This safety alert symbol appears with
most safety statements. It means atten-
tion, become alert, your safety is in-
volved! Please read and abide by the
message that follows the safety alert
symbol.
Indicates a hazardous situation that, if not
avoided, will result in death or serious injury.
Indicates a hazardous situation that, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation that, if not
avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation that can cause damage to the
engine, personal property and/or the environment, or
cause the equipment to operate improperly.
NOTE: Indicates a procedure, practice or condition that
should be followed in order for the engine or component
to function in the manner intended.
REPORTING ACCIDENTS
In case of any accident involving the machine of Hunan
Sinoboom Intelligent Equipment Co., Ltd., notify Hunan
Sinoboom Intelligent Equipment Co., Ltd. immediately,
even if no personal injury or property damage occurs in
the accident. Contact Hunan Sinoboom Intelligent
Equipment Co., Ltd. by telephone and provide all nec-
essary details. Failure to notify the manufacturer within
48 hours of the incident involving the machine of Hunan
Sinoboom Intelligent Equipment Co., Ltd. may void the
product's warranty.
NOTICE
Thoroughly inspect the machine and all its functions
after any accident. Make sure to test it first from the
ground controller and then from the platform control-
ler. Ensure the machine's lifting height does not ex-
ceed 3 m (9.8 ft) until all damage has been repaired
and all controllers operate properly.

© Jun 2022 1-2 1414E Plus Maintenance Manual
SAFETY
ELECTROCUTION
HAZARDS
NOTE: This machine is not insulated and does not have
an electric shock protection function.
All operators and managers shall comply with national
or local regulations regarding the minimum safe dis-
tance of live conductors above the ground. In the ab-
sence of such requirements, operators and managers
should follow the minimum safety distance require-
ments in Table 1-1 Minimum Safe Distance, page 1-
2.
ELECTRICAL SHOCK HAZARDS
• Always maintain a safe distance
from power lines and electrical
equipment in accordance with ap-
plicable government regulations
and see Table 1-1 Minimum Safe
Distance, page 1-2.
• Consider platform movement,
wire swinging or drooping, be-
ware of strong winds or gusts,
and do not operate the machine
when there is lightning or heavy
rain.
• If the machine comes into contact
with live wires, keep away from
the machine. Personnel on the
ground or on the platform must
not touch or operate the machine
until the power is switched off.
• Do not use the machine as a
ground wire during welding and
polishing operations.
Table 1-1 Minimum Safe Distance
Voltage
(Phase to Phase, kV)
Minimum Safe Distance
(m/ft)
0-50 3.05 (10)
50-200 4.60 (15)
200-350 6.10 (20)
350 -500 7.62 (25)
500 -750 10.67 (35)
750 -1000 13.725 (45)
TIPPING HAZARDS AND
RATED LOAD
Maximum rated load bearing capacity of the platform:
Table 1-2
1414E Plus
Platform rectracted 350 kg（772 lb）
Platform extended-fixed
platform only 230kg（507lb）
Platform extended-extension
platform only 120kg（265lb）

SAFETY
1414E Plus Maintenance Manual 1-3 © Jun 2022
TIPPING HAZARDS
• Personnel, equipment and
materials on the platform must
not exceed the maximum load
capacity.
• Only raise or extend the platform
when the machine is on solid,
level ground.
• Do not use the tilt alarm as a level
indicator. The tilt alarm on the
platform will sound only if the
machine is heavily tilted. If the tilt
alarm sounds:
–Be very careful to lower the
platform. Transfer the machine
to solid, level ground. Do not
change the level or limit
switch.
• Do not drive faster than 0.8 km/h
(0.5 mph) when the platform is
raised.
• When the platform is raised, the
machine cannot travel on uneven
terrain, unstable surfaces or in
other dangerous conditions.
• Do not operate the machine
during strong winds or gusts, and
do not increase the surface area
of the platform or load. Increasing
the area exposed to the wind will
reduce the stability of the
machine.
• When the machine is on rough
ground, with gravel or other
uneven surfaces, or near holes
and steep slopes, use caution
and reduce the speed.
• When on the platform do not
push and pull objects outside of
it. The maximum side force
allowed is 400 N（90 lbf）indoor/
200 N（45 lbf）outdoor.
• Do not change any machine parts
that may affect safety and
stability.
• Do not replace key parts that
affect machine stability with
different weights or
specifications.
• Do not modify or change moving
aerial platforms without the
manufacturer’s prior written
permission.
TIPPING HAZARDS
• On the platform, do not attach an
additional device for placing
tools or other materials to the
guardrail. This will increase the
platform weight, surface area and
load.
• Do not place on, or fasten to, any
overhanging load to any part of
this machine.
• Do not place ladders or
scaffolding on the platform or any
parts of the machine.
• Do not use the machine on a
moving or active surface or on a
vehicle. Ensure all tires are in
good condition, the slotted nuts
tightened and the cotter pins
complete.
• Do not use a battery that weighs
less than the original lead acid
battery(40 kg [88 lb]) or lithium
battery(55 kg [121 lb]) . The
battery not only provides power,
it also serves as a counterweight.
The battery is vital to maintaining
the stability of the machine.
• Do not use a platform to propel
machines or other objects.
• Do not let the platform touch
nearby objects.
• Do not tie off the platform with
rope or other binding materials to
nearby objects.
• Do not put a load outside the
platform.
• Do not operate the machine when
the chassis doors are open.
• When the platform is caught or
stuck or when other objects in
the vicinity impede its normal
movement, do not use the
platform controller to lower the
platform. If you intend to lower
the platform with a ground
controller, you must operate it
only after all personnel have left
the platform.

© Jun 2022 1-4 1414E Plus Maintenance Manual
SAFETY
WORK ENVIRONMENT
HAZARDS
UNSAFE JOBSITE HAZARDS
• Do not operate the machine on
surfaces, edges or potholes that
cannot bear the weight of the
machine. Raise or extend the
platform only when the machine is
on firm, flat ground.
• Do not use the tilt alarm as a
horizontal indicator. The tilt alarm
on the platform will sound only
when the machine is heavily tilted.
• If the tilt alarm sounds while lifting
the platform, be very careful when
lowering the platform. Do not
change the level or limit switch.
• Running speed should not exceed
0.8 km/h (0.5 mph) when the
platform rises.
• If the machine can be used
outdoors, never operate it during
strong winds or gusts. Do not lift
the platform when the wind speed
UNSAFE JOBSITE HAZARDS
exceeds 12.5 m/s (28 mph). If the
wind speed exceeds 12.5 m/s (28
mph) after the platform is lifted,
fold the platform and do not
continue to operate the machine.
• Never travel on uneven terrain or
unstable surfaces or in other
dangerous conditions when
raising the platform.
• When the machine retracts, be
careful and slow down when the
machine is moving on uneven
terrain, crushed stone, unstable
or smooth surfaces, steep slopes
and near cave entrances.
• Do not drive or lift the machine on
slopes, steps or vaulted surfaces
that exceed the maximum
climbing capacity of the machine.
Before or during machine operation, check the possible
hazards on the jobsite and beware of the restrictions
within the environment, including flammable and
explosive gas/dust.If the machine is used in any other
applications, or by any other means, as specified by
Sinoboom, it must be approved or guided by the
manufacturer
Table 1-3
BEAUFORT
NUMBER
METERS/
SECOND
MILE/
HOUR DESCRIPTION GROUND CONDITION
0 0～0.2 0～0.5 Calm Calm. Smoke rises vertically.
10.3～1.5 1～3Light air Wind motion visible in smoke.
2 1.6～3.3 4～7Light breeze Wind felt on exposed skin. Leaves rustle.
3 3.4～5.4 8～12 Gentle breeze Leaves and smaller twigs in constant
motion.
4 5.5～7.9 13～18 Moderate breeze Dust and loose paper rise. Small
branches begin to move.
5 8.0～10.7 19～24 Fresh breeze Smaller trees sway.
6 10.8～13.8 25～31 Strong breeze
Large branches in motion. Flags waving
near horizontal. Umbrella use becomes
difficult.
7 13.9～17.1 32～38 Near gale/moderate gale Whole trees in motion. Effort needed to
walk against the wind.

SAFETY
1414E Plus Maintenance Manual 1-5 © Jun 2022
BEAUFORT
NUMBER
METERS/
SECOND
MILE/
HOUR DESCRIPTION GROUND CONDITION
8 17.2～20.7 39～46 Fresh gale Twigs broken from trees. Cars veer on
road.
9 20.8～24.4 47～54 Strong gale Light structure damage.
NOTICE
Maximum slope is suitable for machines with
platform retracted.
Maximum slope: 20% (11.3°）
Maximum slope or gradeability means the maximum
allowable tilt angle of the machine when it is on solid
ground and the platform is only capable of carrying
one person. As the weight of the machine’s platform
increases, the machine’s gradeability reduces.
UNSAFE OPERATION
HAZARDS
At a minimum, operators must operate and maintain the
machine as stated in Operation Manual and
Maintenance Manual in addition to following more
stringent industry regulations and workplace rules.
Never engage in unsafe machine operation.
Do not use the machine in the following situations：
•Unrelated personnel/equipment is present in the
working envelope of the machine.
•Use as a crane (except the custom-made ones with
such functions).
•Use on the truck, trailer, tracked vehicle, ship,
scaffold and the like without written consent by the
manufacturer or a qualified professional.
•Improper securing of the machine to another object
by just sitting it against, fastening or binding.
•Stunt or imprudent use of the machine.
•Overloaded or overmoment sitiuation.
•Other situations as specified in the Manuals.

© Jun 2022 1-6 1414E Plus Maintenance Manual
SAFETY
UNSAFE OPERATION HAZARDS
• Do not push any object outside
the platform. The maximum
lateral force allowed is 400 N
（90 lbf）indoor/200 N（45
lbf）outdoor.
• Do not change any machine
parts that may affect safety and
stability.
• Do not replace key parts that
affect machine stability with
different weights or
specifications.
• Do not change or modify
moving aerial platforms without
the manufacturer’s written
permission.
• On the platform, do not attach
an additional device for placing
tools or other materials to the
guardrail. This will increase the
platform weight, surface area
and load.
• Do not put ladders or
scaffolding on the platform or
any part of this machine.
• Do not use the machine on any
mobile or movable surface or
vehicle. Ensure all tires are in
good condition, the slotted
nuts tightened and the cotter
pins complete.
• Do not use a battery that
weighs less than the original
lead acid battery(40 kg [88 lb])
or lithium battery(55 kg [121 lb])
. The battery not only provides
power, it also serves as a
counterweight. The battery is
vital to maintaining the stability
of the machine.
• Do not place or attach any
suspended load onto any part
of the machine.
• Do not use the machine as a
crane.
• Do not use the platform to push
the machine or other objects.
• Do not allow the platform to
touch nearby objects.
• Do not tie the platform onto
nearby objects.
UNSAFE OPERATION HAZARDS
• Do not put the load outside the
platform.
• When the platform is caught or
stuck or when other objects in
the vicinity impede its normal
movement, do not use the
platform controller to lower the
platform. If you intend to lower
the platform with a ground
controller, you must operate it
only after all personnel have
left the platform.
• Do not operate the machine
when the chassis door box is
open.
• When one or more of the
machine’s tires are off the
ground, evacuate all personnel
before attempting to stabilize
the equipment. Use a crane,
forklift or other suitable
apparatus to stabilize the
equipment.
FALL HAZARDS
At a minimum, operators must operate and maintain the
machine as stated in Operation Manual and in the
Maintenance Manual in addition to following more
stringent industry regulations and workplace rules.