Sinoboom Gtbz26 User manual

GTBZ26/TB26/TB850

GTBZ28J/TB28J/TB910J

Operation

Manual

Part No.505031100002

Rev: A

Aug 2020

GTJZ

0608E (2132E)

GTJZ

0808E (2732E)

GTJZ

0808E (2732E)

GTJZ

0808E (2732E)

长沙市宁乡高新技术产业园区金洲大道东

128 号

0731-87116111 hr@sinoboom . c om . cn ww w .sinoboom . c om . cn

Al w ays F or B e t t er A cc ess Solution s

我们一直在追求新的高度

尺寸：

210×285mm

20mm

产品说明书

PRODU C T MAN U AL

Operating, servicing and maintaining this vehicle or

equipment can expose you to chemicals including engine

exhaust, carbon monoxide, phthalates, and lead, which

are known to the State of California to cause cancer and

birth defects or other reproductive harm. To minimize

exposure, avoid breathing exhaust, do not idle the engine

except as necessary, service your vehicle or equipment in

a well-ventilated area and wear gloves or wash your

hands frequently when servicing. For more information

go to: www.P65warnings.ca.gov.

Please contact us:

Website : www.sinoboom.com

E-mail : [email protected]

Service Tel : 0086-400-608-1289

Sales Tel : 0086-400-601-5828

Fax : 0086–731-87116516-16

Address : No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha,

Hunan, China

Zip Code : 410600

The final interpretation right of this manual belongs to Hunan Sinoboom Intelligent Equipment Co., Ltd.

Manual revision history：

REV DATE DESCRIPTION REMARK

AAug, 2020 Original issue of the manual

APPLICATION

Use the following table to identify the specific serial number for

models included in this manual. Check the model of your machine before

consulting the manual, and then use the correct manual according to the

serial number of the model. See the nameplate on your machine to

identify the model and serial number. (See of the Operation Manual for

details.)

Model

Trade Identification

Serial No.

Metric Imperial

GTBZ26 TB26 TB850 From 0503100100 to present

GTBZ28J TB28J TB910J From 0503200400 to present

NOTE:

•Product model is applied in product nameplate for distinction of products of different main

parameters.

•Product trade identification is applied in marketing and machine decals for distinction of products of

different main parameters, and can be classified as metric type and imperial type: The metric type of

trade identification is applicable to machines for countries/regions using metric system or as

specially required by customers; The imperial type of trade identification is applicable to the

machines for countries/regions using imperial system or as specially required by customers.

This Page Intentionally Left Blank

STATEMENTS

Hunan Sinoboom Intelligent Equipment Co., Ltd. (Hereinafter referred to as Sinoboom) will upload the

latest product manual information to the website www. sinoboom. com as soon as possible. However,

due to continuous product improvement, the information in this manual is subject to change without prior

notice.

This manual covers the basic parts information of one or more products. Therefore, please use this

manual according to your needs. If you find problems in the manual or have suggestions for improve-

ment, feel free to share your feedback with Sinoboom, and we will address these issues as soon as

possible.

Feel free to consult and download the Operation Manual,Maintenance Manual and Parts Manual of the

products you need online at www.sinoboom.com.

Hunan Sinoboom Intelligent Equipment Co., Ltd. retains the right of final interpretation of the manual.

This Page Intentionally Left Blank

GTBZ26&28J Operation Manual i© Aug 2020

TABLE OF CONTENTS

Introduction ..............................v

1 Performance Parameters ...... 1-1

2 Machine Components .......... 2-1

3 Safety............................... 3-1

Safety Definitions . . . . . . . . .. . . . . . . . . . . . 3-1

Reporting Accidents. . . . . . . . . . . . . . . . . . . 3-1

Electrocution Hazards. . . . . . . . . . . . . . . . . 3-1

Tipping Hazards and Rated Load . . . . . 3-2

Work Environment Hazards . . . . . . . . . . . 3-4

Unsafe Operation Hazards. . . . . . . . . . . . 3-5

FallHazards...........................3-7

Collision Hazards . . . . . . . . . . . . . . . . . . . . . 3-7

Crush Hazards . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Explosion and Fire Hazards. . . . . . . . . . . 3-9

Damaged Machine Hazards . . . . . . . . . . 3-9

Bodily Injury Hazards . . . . . . . . . . . . . . . . . 3-9

Battery Hazards . . . . . . . . . . . . . . . . . . . . . . . 3-9

Welding and Polishing Requirements3-10

After Using the Machine. . . . . . . . . . . . . . 3-11

4 Jobsite Inspection............... 4-1

5 Pre-operation Inspection ...... 5-1

Tips for Conducting a Pre-operation

Inspection.............................5-1

Conducting a Pre-operation

Inspection.............................5-2

Inspecting Parts . . . . . . . . . . . . . . . . . . . . . . . 5-2

Inspecting Entire Machine . . . . . . . . . . . . 5-2

Inspect Hydraulic Oil Level . . . . . . . . . . . . 5-2

Inpsecting Fuel Level . . . . . . . . . . . . . . . . . 5-3

Inspecting Engine Oil Level . . . . . . . . . . . 5-4

Inspecting Coolant Level . . . . . . . . . . . . . . 5-5

Inspecting the Battery . . . . . . . . . . . . . . . . . 5-6

6 Pre-operation Function Test .. 6-1

Preparing for a Pre-operation Function

Test....................................6-1

Testing the Ground Controller . . . . . . . . . 6-1

Testing ground controller . . . . . . . . . . . 6-4

Testing the horn. . . . . . . . . . . . . . . . . . . . . 6-4

Testing the engine start function . . . . 6-4

Testing the emergency stop function6-4

Testing the Ground/Platform select

function .............................6-4

Testing the enable function . . . . . . . . . 6-5

Testing the boom up/down function. 6-5

Testing the main boom telescope

function .............................6-5

Testing the turntable rotate function 6-5

Testing the platform level function . . 6-5

Testing the platform rotate function . 6-6

Testing jib up/down function-

GTBZ28J ...........................6-6

Testing jib rotate function-

GTBZ28J (if equipped) . . . . . . . . . . . . . 6-6

Testing the emergency power

function .............................6-6

Testing the engine high/low speed

select function . . . . . . . . . . . . . . . . . . . . . . 6-6

Testing the buzzer function . . . . . . . . . 6-6

Testing the engine preheat

function (if equipped) . . . . . . . . . . . . . . . 6-7

Testing the Platform Controller . . . . . . . . 6-7

Testing platform controller . . . . . . . . . . 6-9

Testing the footswitch. . . . . . . . . . . . . . . 6-9

Testing the horn. . . . . . . . . . . . . . . . . . . . . 6-9

Testing the engine start function . . . . 6-9

Testing the emergency stop

function ............................6-10

Testing the drive function . . . . . . . . . .6-10

Testing the steer function . . . . . . . . . .6-10

Testing the drive high/low speed

select function . . . . . . . . . . . . . . . . . . . . .6-10

Testing the main boom up/down

function ............................6-11

Testing the main boom telescope

function ............................6-11

Testing the turntable rotate

function ............................6-11

Testing the platform level fuction. . . 6-11

Testing the platform rotate function 6-12

Testing the jib up/down function-

GTBZ28J ..........................6-12

Testing the jib rotate function-

GTBZ28J (if equipped) . . . . . . . . . . . .6-12

Testing the emergency power

function ............................6-12

Testing the engine high/low speed

select function . . . . . . . . . . . . . . . . . . . . .6-12

Testing the rear detection fuction . .6-12

Testing the reverse drive function. .6-13

Testing the buzzer function . . . . . . . .6-13

Testing the system distress alert

function ............................6-13

Testing the overload alert function .6-13

Testing the tilt alart function. . . . . . . .6-13

Testing the angle sensor

malfunction alart function . . . . . . . . . .6-13

Testing the length sensor

malfunction alart function . . . . . . . . . .6-13

Testing the hydraulic generator