Sioux Tools C Series Datasheet

1
Form Z757
Date 2005May25/A
Page 1 of 4
Printed In U.S.A.
INSTRUCTIONS AND PARTS LIST FOR 2L1600TH-107 POWER UNIT
SERIAL C
E SURE TO LU RICATE
All Sioux Air Tools are manufactured to extremely close tolerances. Reasonable care and preventative maintenance will greatly
prolong their service life.
This line of tools is designed for a long life of continuous duty on assembly lines, with a minimum of service and maintenance.
Rotating parts are mounted on extra capacity ball bearings, rotors and spindles are finished to extreme accuracy for power and
low air consumption, gears and pinions are oversize and correctly hardened for quietness and long life.
Special attention has been given to ease of servicing. These tools can be disassembled and reassembled with ease.
Before connecting the tool, blow the air line to remove water and dirt which may have accumulated. This is especially important
for a new line or when the line has not been used for some time.
LU RICATION
GEARS
The gears are lubricated at the factory. Every 100 hours of operation add 1/4 oz. of Sioux Grease No. 289.
AIR MOTORS
Sioux Air line lubricators are recommended. When used adjust lubricator to deliver 2 to 4 drops of Sioux Air Motor Oil No. 288
per minute to the air tool. If tool is not used with a lubricator, place 10 to 15 drops of Sioux No. 288 oil into air inlet twice daily.
OPERATION
The air motor is started by depressing the operating lever or trigger. Motor speed may be controlled by adjusting the slotted
head control which is located on the tool housing or on some models on the trigger surface.
HOSE AND HOSE CONNECTION
Air supply hose should not be less than 3/8" I.D. If extension hose is necessary, use 1/2" I.D. hose with couplings not less than
3/8" I.D.
SAFETY PRECAUTIONS
1. Keep Work Area Clean: Cluttered areas and benches invite accidents.
2. Wear Proper Apparel: No loose clothing or jewelry to get caught in moving parts.
3. Use Safety Glasses: Protect your eyes.
4. Secure Work: Use clamps or vise to hold work. Its safer than using your hand and it frees both hands to operate tool.
5. Dont Overreach: Keep proper footing and balance at all times.
6. Maintain Tools With Care: Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating
and changing accessories.
7. Disconnect Tools: When not in use, before servicing, or when changing accessories such as blades, bits and etc.
8. Remove Adjusting Key and Wrenches: Form habit of checking to see that keys and adjusting wrenches are removed from
tool before turning it on.
9. Caution: The use of an accessory with this tool not provided or specified by SIOUX TOOLS INC. may be hazardous.

2
Fig. Part
No. No. Description
1. 10220 BearingBall
2. 13550 End PlateFront
3. 14342 RingO
4. 64057 Cylinder
5. 68403 Pin
6. 67855 Rotor
7. 63192 AssyRotor Vane (Set of 5)
8. 10552 End PlateRear
9. 10230 BearingBall
10. 21491 RingRetaining
11. 68768 Housing
12. 54843 SpeedControl
13. 14290 RingO
14. 14291 RingO
15. 54844 RetainerSpeed Control
16. 14309 RingO
17. 14333 RingO
18. 40116 MaterialExhaust
19. 04042 CoverHousing
20. 54837 AdaptorIntake
21. 14312 RingO
22. 30463 Screen
23. 21541 RingRetaining
Complete Assemblies:
75202 Ass'yMotor (Includes Figs. 1 10)
Fig. Part
No. No. Description
*Order Quantity As Required
FURNISH CATALOG, SERIAL, AND MODEL NUM ER WHEN
ORDERING PARTS
INSTRUCTIONS AND PARTS LIST FOR 2L1600TH-107 POWER UNIT
SERIAL C

3
*Order Quantity As Required
FURNISH CATALOG, SERIAL, AND MODEL NUM ER WHEN
ORDERING PARTS
1. 67928 CaseGear
2. 30375 FittingGrease
3. 67858 GearRing
4. 67895 AssyPlanetary Reduction (2000RPM)
5. 10228 BearingBall
6. 25439 Washer (2)*
7. 67870 CarrierGear (2000RPM)
8. 10203 BearingBall
9. 67857 Pin (2)*
10. 67944 AssyGear & Bearing (2000RPM)(2)*
11. 10080 BearingNeedle (4)*
INSTRUCTIONS AND PARTS LIST FOR 2L1600TH-107 POWER UNIT
SERIAL C
Fig. Part
No. No. Description
Single Reduction Gear Case
(2000 RPM)

4
Printed In U.S.A.
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or
other reproductive harm.
El polvo generado al lijar, aserrar, afilar, taladrar y realizar otras tareas de
construcción contiene sustancias uímicas ue podrían causar cáncer,
malformaciones congénitas y otras alteraciones del aparato reproductor.

This pdf incorporates the following model numbers:
2L1600TH-107