SMART Board 6052i User manual

Troubleshooting guide for
the SMART Board™ 6052i
interactive display
Use the following table to find troubleshooting topics related to your issue.
Other troubleshooting resources
•NEC Multisync S521 User’s Manual
•SMART Board 6052i Interactive Display Installation and User’s Guide
Issue Troubleshooting topics
You don’t know how to set up your
interactive display.
See Setting up your interactive display
on page 3.
You can’t see your computer desktop on
your interactive display.
See Resolving blank-screen issues on
page 4.
Your interactive display image is low
quality.
See Resolving low quality image issues
on page 5.
You don’t have touch interactivity with
your interactive display.
See Resolving touch interactivity issues
on page 6.
You can’t draw with digital ink. See Resolving digital ink issues on
page 9.
Your digital ink is low quality or
inconsistent.
See Resolving digital ink quality issues
on page 10.
You don’t hear sound when you play a
video or sound file on your interactive
display.
See Resolving sound issues with
external speakers attached on page 11.
IMPORTANT
There are no built-in speakers on your interactive display. You must connect
external speakers to have sound.

2| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
Parts of your interactive display
Interactive display bottom terminal panel
1 Main power switch 8 RGB/HV out
2 AC in 9 Video in
3 Display port 10 Video out (BNC)
4 HDMI 11 DVD/HD (RCA)
5 DVI in (DVI-D) 12 S-Video in
6 VGA in 13 Audio in 1, 2, 3
7 RGB/HV in 14 Audio out
Cameras
Touch connection panel
(behind the interactive display)
Control panel
(bottom of interactive display)
Terminal panel
(bottom of interactive display)
Wireless remote
control sensor
and display
status light
LCD screen
Pencil ledge
Pencil
14
236
5
8
7
10
911 14
13
12

3| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
Setting up your interactive display
Some interactive display issues are caused by incorrect or insecure cabling
connections. Use the diagram and steps below to resolve these issues.
To set up your
interactive display
1. Connect the supplied VGA cable or an HDMI cable (not supplied) from your
computer’s video output connection to your interactive display’s terminal panel
(see page 2).
2. Connect the supplied USB 2.0 cable from the touch connection panel to a USB
2.0 connector on your computer.
NOTE
USB 1.1 connections result in reduced performance.
3. Connect the supplied power cable from the AC connector in your interactive
display’s bottom terminal panel (see page 2) to the AC power outlet.
4. Connect the supplied power cable from the touch connection panel of your
interactive display to the AC power outlet.
5. Connect the power cable from your computer to the AC power outlet.
6. Turn on the main power switch on the interactive display’s terminal panel.
7. Connect your computer to the Internet, if available.
Display VGA
cable
Display
power cord
Touch connection
panel power cord
Internet
connection
Touch connection
panel USB 2.0 cable
Computer
power cord
Touch connection panel
Terminal
panel

4| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
Resolving blank-screen issues
Use the following troubleshooting table when you attempt to turn on your interactive
display and you don’t see an image on its screen.
Begin by looking at the display status light in the wireless remote control sensor
screen located in the lower right corner of your interactive display (see page 2).
Symptom Possible causes Actions
You don’t see the display
status light in the wireless
remote control sensor
screen.
Your interactive display
isn’t plugged in.
Connect your interactive
display power cable to a
power connector (see
page 3).
The main power switch is
turned off.
Turn on the main power
switch on the terminal
panel (see page 2).
The display status light in
the wireless remote control
sensor screen is red.
Your interactive display is
turned off.
Press the power button on
the remote or your
interactive display’s control
panel.
When you turn on your
interactive display, you see
a “No input signal”
message and the display
status light turns red again.
Your computer isn’t turned
on.
Turn on your computer.
Your computer isn’t
connected to your
interactive display.
Connect your computer to
your interactive display
with a VGA cable (see
page 3).
The display status light is
green and the screen is
blank.
Your computer is in
standby mode.
Touch the screen.
OR
Press a key on the
keyboard.
OR
Move your mouse.

5| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
Resolving low quality image issues
Use the following troubleshooting table when the image you see on your interactive
display is low quality or not what you expect.
You can often resolve these issues by tightening video connections. You can also
make display adjustments with the on-screen menu, or perform a factory reset (see
below) to restore all defaults.
For more information on the on-screen menu, see the NEC Multisync S521 User’s
Manual.
To perform a
factory reset
1. Press the Menu button on the remote control.
2. Use the arrow keys to select Pro Advanced.
3. Select FACTORY RESET > Yes.
Symptom Possible causes Actions
The image is too large or
doesn’t completely fill your
interactive display.
Your computer’s video
resolution settings don't
match your display’s native
resolution.
Change your computer’s
screen resolution to the
recommendations in the
NEC Multisync S521
User’s Manual.
The image is unstable,
unfocused or moves.
You have a loose video
connection.
Secure the VGA cable for
both your computer and
your interactive display.
You computer has an
ineffective video display
card.
Connect a different
computer. If this improves
performance, consider
replacing the video card in
the original computer.
The image is too light, too
dark or has other display
issues.
You may have improper
settings in your interactive
display.
Use the On-Screen-
Display menu button on
the remote to adjust picture
settings, or perform a
factory reset.
There is a persistent image
on your screen.
An image was displayed
for too long.
Turn off your interactive
display for as long as the
persistent image was on
the screen.

6| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
Resolving touch interactivity issues
Use the following troubleshooting table when you can see your computer’s desktop,
but you’re unable to open files easily by touch.
These issues are typically due to loose connections for the touch connection panel
(see page 3).
Symptom Possible causes Actions
When you touch the
screen, no cursor appears
and you can’t move icons.
Your touch connection
panel isn’t connected to
your computer and a
power source.
Ensure you have complete
connections (see page 3).
Your touch connection
panel is unresponsive.
Disconnect the power
supply for the touch
connection panel for five
seconds, and then
reconnect it.
Your SMART Board
services aren’t running.
Click the SMART Icon ,
and then select Control
Panel > Connection
Wizard.
Your computer doesn’t
recognize your interactive
display due to conflicting
Windows® operating
system registry entries.
Refer to See Correcting
Registry or System
Preferences File Issues
(document 135245).
Your cursor is erratic or
jumps locations.
Your touch connection
panel is unresponsive,
possibly due to static.
Unplug the power supply
for the touch connection
panel for five seconds, and
then reconnect it.

7| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
A cursor appears when
you touch the screen, but it
is in the wrong location.
Your interactive display
isn’t calibrated.
Calibrate your interactive
display. Refer to the
SMART Board 6052i
Interactive Display
Installation and User’s
Guide.
You aren’t touching the
screen at right angles.
See Touching and Drawing
on Your SMART Board
Interactive Whiteboard is
Inaccurate (document
131299) for more details.
An area of the screen
doesn’t respond to your
touch.
Something is blocking the
cameras.
Ensure nothing is taped to
the screen or blocking the
cameras (see page 2).
Bright lights are interfering
with the cameras.
Close any blinds and
shades or dim all halogen
and LED lights.
Touch interactivity is slow
or sluggish.
Your computer doesn’t
meet requirements.
Upgrade your computer or
replace it with a more
powerful computer.
Your computer is running
too many applications.
Close some open
applications.
You haven’t used a USB
2.0 cable to connect your
interactive display to your
computer.
Use a USB 2.0 cable and
ensure it is connected to a
USB 2.0 connector on your
computer.
You are unable to use
multitouch gestures.
Multitouch gestures aren’t
activated.
OR
You aren’t familiar with
gestures.
Refer to Using Touch
Gestures with Your
SMART Board Interactive
Display (document
144789).
You have conflicting
registry entries.
Refer to Correcting
Registry or System
Preferences File Issues
(document 135245).
Symptom Possible causes Actions

8| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
To troubleshoot using
LED status and
diagnostic lights
1. Observe the diagonostic and status lights on the touch connection panel behind
the interactive display.
2. Use the following table
Diagnostic
LED
Status
LED
Touch connection panel
condition Solution
Off Off Touch connection panel is
turned off or power cable is
disconnected.
Connect the power cable to the
touch connection panel.
Off Flashing
green
Software is starting or
touch connection panel is
initializing.
Don’t touch your panel until
initializing is complete.
Green
OR
Alternating
green and
orange
Green Touch connection panel is
functioning within normal
parameters.
None.
Flashing
green
Green No SMART software
detected.
Start SMART software.
Green
OR
Alternating
green and
orange
Red Error detected. Run the SMART Connection
Wizard’s troubleshooting
procedures to determine the
cause.
Flashing
red
Red No USB connection. Check the cable between the
touch connection panel and
computer.
Flashing
green
Red No SMART software
detected.
Start SMART software, and
then run the SMART
Connection Wizard’s
troubleshooting procedures.
Flashing
orange
Red SMART software isn’t
responding.
Restart your computer.
Diagnostic LED Status LED

9| TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
Resolving digital ink issues
Use the following troubleshooting table when you can easily move icons on your
interactive display screen with your finger, but you can’t draw in digital ink with your
pencil.
Green
OR
Alternating
green and
orange
Flashing
orange
Touch connection panel is
updating firmware.
Wait for the update to finish.
Flashing
green
Flashing
orange
No USB connection. Check the cable between the
touch connection panel and the
computer.
CAUTION
To avoid memory loss, do
not disconnect the cable.
Red Flashing
orange
Corrupted firmware. Run the SMART Firmware
Upgrade Wizard.
Off Flashing
orange
Computer is in Standby
mode.
Turn on the computer.
Symptom Possible causes Actions
The SMART Board icon
or the SMART Meeting Pro
icon doesn’t appear in
the notification area
(Windows computers) or
Dock (Mac computers).
SMART software isn’t
running.
Open the SMART Board
Drivers folder in your list of
programs, and then select
SMART Board Tools.
SMART software isn’t
installed.
Download and install
SMART software from the
Software downloads page.
Your interactive display
includes either SMART
Meeting Pro Premium or
SMART Notebook
software.
Diagnostic
LED
Status
LED
Touch connection panel
condition Solution

10 | TROUBLESHOOTING GUIDE FOR THE SMART BOARD 6052I INTERACTIVE
DISPLAY
Resolving digital ink quality issues
Use the following troubleshooting table when digital ink quality is reduced.
There is a red X on your
SMART Board or
SMART Meeting Pro
icon.
Your computer can’t find
your interactive display.
Confirm that your
interactive display’s touch
connection panel is
connected to both your
computer and a power
source (see page 3).
You see the SMART Board
or SMART Meeting Pro
icon, but you can’t draw in
digital ink with the pencil.
The pencil’s batteries are
weak, dead or backwards
in the pencil.
Ensure the pencil batteries
are fresh and oriented
properly.
The pencil nib is worn. Replace the pencil nib.
Either the SMART Board
diagnostics window or
SMART Board control
panel is open.
Close the SMART Board
diagnostics window and
the SMART Board control
panel.
Symptom Possible causes Actions
Gaps appear in digital ink
lines or areas of the screen
are inactive.
The camera view is
obstructed.
Remove anything blocking
the cameras’ views.
You can write in digital ink,
but it is slow or sluggish.
Your computer doesn’t
meet requirements.
Upgrade your computer or
replace it with a more
powerful computer.
Your computer is running
too many applications.
Close some open
applications.
You haven’t used a USB
2.0 cable to connect your
interactive display to your
computer.
Use a USB 2.0 cable and
ensure it is connected to a
USB 2.0 connector on your
computer.
Symptom Possible causes Actions