ModelModel
Maximum supply pressureMaximum supply pressure
Minimum supply pressureMinimum supply pressure
24 VDC24 VDC ±±10%, 12 to 15 VDC10%, 12 to 15 VDC
Set pressure +0.1 MPaSet pressure +0.1 MPa
Set pressure rangeSet pressure range Note 1)Note 1)
0.2 MPa0.2 MPa
Input signalInput signal
InputInput
impedanceimpedance
Output pressureOutput pressure
displaydisplay Note 4)Note 4)
WeightWeight Note 9)Note 9)
AccuracyAccuracy
Minimum unitMinimum unit
ITV10ITV10
ITV20ITV20
ITV30ITV30
Ambient and fluid temperatureAmbient and fluid temperature
EnclosureEnclosure
1.0 MPa1.0 MPa
00..00005 5 tto o 00..1 1 MMPPaa 00..00005 5 tto o 00..5 5 MMPPaa 00..00005 5 tto o 00..9 9 MMPPaa
JIS SymbolJIS Symbol
4 to 20 mA DC, 0 to 20 mA DC (Sink type)4 to 20 mA DC, 0 to 20 mA DC (Sink type)
0 to 5 VDC, 0 to 10 VDC0 to 5 VDC, 0 to 10 VDC
4 points (Negative common), 16 points 4 points (Negative common), 16 points (No common polarity)(No common polarity)
250250 ΩΩor lessor less Note 6)Note 6)
Approx. 6.5 kApprox. 6.5 kΩΩ
Power supply voltage 24 VDC type: Approx. 4.7 kPower supply voltage 24 VDC type: Approx. 4.7 kΩΩ
Power supply voltage 12 VDC type: Approx. 2.0 kPower supply voltage 12 VDC type: Approx. 2.0 kΩΩ
LinearityLinearity
HysteresisHysteresis
RepeatabilityRepeatability
SensitivitySensitivity
TemperaturTemperature e characteristicharacteristicscs
Power supplyPower supply
VoltageVoltage
CurrentCurrent
consumptionconsumption
±±1% F.S. or less1% F.S. or less
0.5% F.S. or less0.5% F.S. or less
±±0.5% F.S. or less0.5% F.S. or less
0.2% F.S. or less0.2% F.S. or less
±±0.12% F.S./0.12% F.S./
°°C or lessC or less
±±2% F.S.2% F.S. ±±1 digit or less1 digit or less
MPa: 0.001, kgf/cmMPa: 0.001, kgf/cm22: 0.01, bar: 0.01, psi: 0.1: 0.01, bar: 0.01, psi: 0.1 Note 5)Note 5), kPa: 1, kPa: 1
0 to 500 to 50°°C (No condensation)C (No condensation)
IP65IP65
Approx. 250 g (without options)Approx. 250 g (without options)
Approx. 350 g (without options)Approx. 350 g (without options)
Approx. 645 g (without options)Approx. 645 g (without options)
NPN open collector output: Max. 30 V, 80 mANPN open collector output: Max. 30 V, 80 mA
PNP open collector output: Max. 80 mAPNP open collector output: Max. 80 mA
Power supply voltage 24 VDC type: 0.12 A Power supply voltage 24 VDC type: 0.12 A or lessor less Note 8)Note 8)
Power supply voltage 12 to 15 VDC type: 0.18 Power supply voltage 12 to 15 VDC type: 0.18 A or lessA or less
ITV105ITV105
ITV205ITV205
ITV305ITV305
ITV103ITV103
ITV203ITV203
ITV303ITV303
ITV101ITV101
ITV201ITV201
ITV301ITV301
1 to 5 VDC 1 to 5 VDC (Output impedance: Approx. 1 k(Output impedance: Approx. 1 kΩΩ))
4 to 20 mA DC (Sink type4 to 20 mA DC (Sink type) ) (Load impedance: (Load impedance: 250250 ΩΩor less)or less)
Output accuracyOutput accuracy ±±6% F.S. or less6% F.S. or less
Figure 1. Input/output characteristics chartFigure 1. Input/output characteristics chart
Input signal (%F.S.)Input signal (%F.S.)
00 00 110000
OO
uu
tt
pp
uu
tt
pp
rr
ee
ss
ss
uu
rr
ee
((
MM
PP
aa
))
This range is outsideThis range is outside
of the control (output).of the control (output).
0.005MPa0.005MPa
Rated pressureRated pressure
ITV3000ITV3000 Fieldbus-compatibleFieldbus-compatible
modelmodel
ITV2000ITV2000ITV1000ITV1000
Note 1) Please refer to Figure 1 for the Note 1) Please refer to Figure 1 for the relationship between set pressurrelationship between set pressure and input. Because the maximum set pres-e and input. Because the maximum set pres-
sure differs for each pressure display, refer to page 201.sure differs for each pressure display, refer to page 201.
Note 2) 2-wire type 4 to 20 mA DC is not available. Power supply voltage (24 VDC or 12 to 15 VDC) is Note 2) 2-wire type 4 to 20 mA DC is not available. Power supply voltage (24 VDC or 12 to 15 VDC) is required.required.
Note 3) Select either analog output or switch output.Note 3) Select either analog output or switch output.
Further, when switch output is selected, select either NPN output or PNP Further, when switch output is selected, select either NPN output or PNP output.output.
When measuring ITV analog output from 1 to 5 VDC, if the load impedance is less than 100 kWhen measuring ITV analog output from 1 to 5 VDC, if the load impedance is less than 100 k ΩΩ, the analog, the analog
output monitor accuracy of withinoutput monitor accuracy of within ±±6% (full span) may not be available. The product with the accuracy of6% (full span) may not be available. The product with the accuracy of
withinwithin ±±6% is supplied 6% is supplied upon your request. Output pressure remains unaffected.upon your request. Output pressure remains unaffected.
NoteNote4)4)Adjustment of numerical values such as the zero/span adjustment or preset input type is set based on theAdjustment of numerical values such as the zero/span adjustment or preset input type is set based on the
minimum units for output pressure display (e.g. 0.001 to 0.500 MPa). Note that the minimum units for output pressure display (e.g. 0.001 to 0.500 MPa). Note that the unit cannot be changed.unit cannot be changed.
Note 5) The minimum unit for 0.9 MPa Note 5) The minimum unit for 0.9 MPa (130 psi) types is 1 (130 psi) types is 1 psi.psi.
Note 6)Note 6)Value for the state with no over current circuit included. If an allowance is provided for an over Value for the state with no over current circuit included. If an allowance is provided for an over current circuit, thecurrent circuit, the
input impedance varies depending on the input current. This is input impedance varies depending on the input current. This is 350350 ΩΩor less for an input current of 20 mA DC.or less for an input current of 20 mA DC.
Note 7) The above characteristics are confined to the Note 7) The above characteristics are confined to the static state. When air is static state. When air is consumed on the output side, the pres-consumed on the output side, the pres-
sure may fluctuate.sure may fluctuate.
Note 8) For communication models, the maximum current consumNote 8) For communication models, the maximum current consumption is 0.16 A ption is 0.16 A or less.or less.
Note 9) For communication models, add roughly 80 g to the Note 9) For communication models, add roughly 80 g to the weight (100 g for the PROFIBUS DP).weight (100 g for the PROFIBUS DP).
Note 10) The ITV1000 series Note 10) The ITV1000 series is a is a Grease-free specificatioGrease-free specification (Wetted parts).n (Wetted parts).
Standard SpecificationsStandard Specifications
NNootte e 1100)) NNootte e 1100)) NNootte e 1100))
Current typeCurrent type Note 2)Note 2)
Voltage typeVoltage type
Preset inputPreset input
Current typeCurrent type
Voltage typeVoltage type
Preset inputPreset input
SwitchSwitch
outputoutput
AnalogAnalog
outputoutput
Output signalOutput signal
(monitor(monitor
output)output)
Note 3)Note 3)
Communication Communication SpecificatiSpecificationsons
(CC, DE, PR, RC)(CC, DE, PR, RC)
ModelModel
NNoot t bbuuiillt t iinntto o tthhe e pprroodduucctt ——
Note 1) Note that version information is subject to Note 1) Note that version information is subject to change.change.
Note 2) Configuration files can Note 2) Configuration files can be downloaded from the operation manual page be downloaded from the operation manual page on SMC's website:http://www.smcwoon SMC's website:http://www.smcworld.comrld.com
Note 3) The output HOLD value when a Note 3) The output HOLD value when a CC-Link communicatCC-Link communications error occurs can be set ions error occurs can be set based on the bit area data.based on the bit area data.
Note 4) The insulation between the electrical signal of the Note 4) The insulation between the electrical signal of the communication system and ITV power supply.communication system and ITV power supply.
156 k/625 k156 k/625 k
2.5 M/5 M/10 M bps2.5 M/5 M/10 M bps 125 k/250 k/500 k bps125 k/250 k/500 k bps
9.6 k/19.2 k/45.45 k9.6 k/19.2 k/45.45 k
93.75 k/187.5 k/500 k93.75 k/187.5 k/500 k
1.5 M/3 M/6 M/12 M bps1.5 M/3 M/6 M/12 M bps
Built into the product (Switch setting)Built into the product (Switch setting)
HOLD/CLEARHOLD/CLEAR
(Switch setting)(Switch setting)
4 word/4 word, 32 bit/32 bit4 word/4 word, 32 bit/32 bit
(per station, remote device station)(per station, remote device station)
HOLDHOLDNote 3)Note 3)
/CLEAR/CLEAR
(Switch setting)(Switch setting)
Electric insulationElectric insulationNote 4)Note 4)
Terminating resistorTerminating resistor
IInnssuullaattiioonn IInnssuullaattiioonn IInnssuullaattiioonn NNoonn--iinnssuullaattiioonn
Electro-Pneumatic RegulatorElectro-Pneumatic Regulator SeriesSeries ITV1000/2000/3000ITV1000/2000/3000
Fail safeFail safe
Communication data resolutionCommunication data resolution
I/O occupation areaI/O occupation area
(input/output data)(input/output data)
Configulation fileConfigulation fileNote 2)Note 2)
ProtocolProtocol
VersionVersionNote 1)Note 1)
CommunicationCommunication
speedspeed
ITVITV000-CC0-CC
CC-LinkCC-Link
Ver 1.10Ver 1.10
——
12 bit (4096 resolution)12 bit (4096 resolution)
ITVITV000-DE0-DE
DeviceNet™DeviceNet™
Volume1 (Edition3.8), Volume3 (Edition1.5)Volume1 (Edition3.8), Volume3 (Edition1.5)
EDSEDS
16 bit/16 bit16 bit/16 bit
12 bit (4096 resolution)12 bit (4096 resolution)
ITVITV000-PR0-PR
PROFIBUS DPPROFIBUS DP
DP-V0DP-V0
GSDGSD
16 bit/16 bit16 bit/16 bit
12 bit (4096 resolution)12 bit (4096 resolution)
CLEARCLEAR
ITVITV000-RC0-RC
RS-232CRS-232C
——
9.6 kbps9.6 kbps
——
——
10 bit (1024 resolution)10 bit (1024 resolution)
HOLDHOLD
167167
A
A
ll
pp
hh
aa
bb
ee
tt
ii
cc
aa
ll
II
nn
dd
ee
xx
LL
ee
nn
gg
tt
hh
MM
ee
aa
ss
uu
rr
ii
nn
gg
//
CC
oo
uu
nn
tt
ee
rr
SS
tt
aa
tt
ii
cc
EE
ll
ee
cc
tt
rr
ii
cc
ii
tt
yy
EE
ll
ii
mm
ii
nn
aa
tt
ii
oo
nn
EE
qq
uu
ii
pp
mm
ee
nn
tt
RR
ee
dd
uu
cc
ee
dd
--
ww
ii
rr
ii
nn
gg
FF
ii
ee
ll
dd
bb
uu
ss
SS
yy
ss
tt
ee
mm
PP
oo
ss
ii
tt
ii
oo
nn
DD
ee
tt
ee
cc
tt
ii
oo
nn
SS
ww
ii
tt
cc
hh
FF
ll
oo
ww
SS
ee
nn
ss
oo
rr
PP
rr
ee
ss
ss
uu
rr
ee
CC
oo
nn
tt
rr
oo
ll
PP
rr
ee
ss
ss
uu
rr
ee
SS
ee
nn
ss
oo
rr
DD