SMITH SYSTEM 26681 User manual

For assistance in assembling product, or to place
an order please contact customer service at
Form# 179874 800-328-1061 02/2013
Library Carrel Adders
(Adder Unit) See Instruction Sheet 179873 for Starter Unit.
Intermediate
Panel
Right
Panel
Left
Panel
Model
26681
26683
26685

For assistance in assembling product, or to place
an order please contact customer service at
Form# 179874 800-328-1061 02/2013
Special Notes:
1. Check that all components are accounted for and undamaged before assembling.
2. Assemble the product in a clean and dry area.
3. For larger units you may need another person to help assemble the product.
4. Clean the product with a mild cleaner and a damp cloth.
Tools:
You will need a Phillips Head Screwdriver.
Hardware and Components
Replacement Pack 74125 Includes
(12) 70080- 10x5/8 Truss Head Phillips Head
(6) 70869- Connector Nut ¼-20X17mm
(6) 70870- Connector Bolt ¼-20X23mm
(4) 70226- Machine Screw 10-32X.5
(2) 77813- Hex Key- 3/16” Short Arm
#10 Wood Screws
(Qty. 12)
P/N-70080
Connector Bolts (Qty. 3)
P/N
-70869- Connector Bolt ¼-20X17mm
P/N-70870 Connector Nut ¼-20X23mm
Phillips Head Machine Screws
(Qty. 4)
P/N-70226
Allen Wrench
(Qty. 2)
P/N-77813
Cross Brace
(Qty. 1)
Brackets (Qty. 2)
Back Panel (Qty. 1)
Top (Qty. 1)
Intermediate Panel
(Qty. 1)
(Predrilled on both sides)

For assistance in assembling product, or to place
an order please contact customer service at
Form# 179874 800-328-1061 02/2013
Assembly Instructions
Library Carrels (Starter Unit)
Urgent: Back panel orientation determines the top height. By rotating 180 degrees you can change
the carrel to the desk height or the kiosk height.
Important Information: The starter unit comes with a left and a right panel (See Drawing 1).
Before assembling our adder units, choose the side that the adder will be on. When assembling the
adder, the right or left starter panels will be replaced (depending on which side you choose) with the
intermediate panel (See Drawing 2).
“C” brace on
back panel
*Due to size, we recommend that
two people should be involved in
assembling this product.
Drawing 1
Starter Unit
Right
Panel
Left
Panel
Drawing 2
Intermediate
Panel
Intermediate
Panel
Right
Panel
Left
Panel

For assistance in assembling product, or to place
an order please contact customer service at
Form# 179874 800-328-1061 02/2013
Step 1: Lay the starter unit on the floor; disconnect the connector bolts from the side panel by using the
“L” wrench (See Drawing 1A). Next, detach the machine screws from the cross brace; finally remove the
3 wood screws that connect the bracket to the side panel.
Step 2: With help, lay the intermediate panel on the floor while aligning the cross bar with the pilot
holes. Attach together by using (2) Phillips head machine screws. Next, attach the bracket, located
underneath the top, to the intermediate panel by using (3) wood screws. Lay the second back panel,
with the bracket facing up, on the other side of the intermediate panel. Verify alignment with the pilot
holes and attach using (3) connector bolts.
Left/Right
Panel
Left/Right
Panel
Intermediate
Panel
Left/Right
Panel
Drawing 2A
Back panel orientation
determines the top height. By
rotati
ng 180 degrees, you can
change the carrel to desk height
or kiosk height.
28” Desk Height
36” Kiosk Height

For assistance in assembling product, or to place
an order please contact customer service at
Form# 179874 800-328-1061 02/2013
Step 3: With help, lay the side panel on the floor while aligning the cross bar with the pilot hole. Attach
together by using (2) Machine Screws (See Drawing 3A).
Step 4: Lay the adder unit on the floor and align the cross bar with the (2) pilot holes. Attach together by
using (2) machine screws. Next, attach the back panel with the adder unit by using (3) connector bolts.
Next, attach the brackets to either kiosk or desk height by using (6) wood screws.
Left/Right
Panel
Drawing 3A
Adder
Unit
Starter
Unit

For assistance in assembling product, or to place
an order please contact customer service at
Form# 179874 800-328-1061 02/2013
Step 5: With help, se the unit upright on its feet and slide the work surface above both brackets until it
runs flush against the back panel. Align the predrilled holes underneath the table top with the brackets.
Using (6) wood screws, attach the top to the brackets (See Drawing 5A).
Drawing 5A