SOMFY inteo CENTRALIS UNO IB VB User manual

The CENTRALIS UNO IB VB is an individual control of AC motor with link to master control.
The CENTRALIS UNO IB VB is dedicated to exterior venetian blind application.
®
inteoCENTRALIS UNO IB VB
INSTALLATION guide
Ref.9000835
1
Installation:
280 mm
80 mm
Characteristics:
33 mm 17 mm
Cabling
Respect the electrical standards in force as well as the following points:
- disconnect the mains before carrying out any work.
- ensure that no forces act on the screw terminals after installation.
- Do not forget to mount the protection cover to separate the cables for the
BUS line and the cables for the power supply.
•Main supply : 220-240V 50Hz.
•Class II product
•Protection index IP40.
•Output : 250V~ 3A cosφ0,8.
•Output temporisation : momentary or fixed (activ for 180s).
•Environmental conditions for use :
- temperature +5°C to +40°C (no condensation allowed).
- pollution degree typical for usual living space.
EN60730-1
EN50081-1
EN50082-1
Installation allowed only by authorized electrician.
Before connecting the unit, read the instructions carefully.
• Compatibility with the SOMFY “IB” BUS line (common = +V).
• Integrated switch to disable the master commands.
• Possibility to set an intermediate oriented position.
+
NL N
SUPPLY
230V 50Hz
Phase
Neutral
Earth
LT motor
DOWN
PE
N
UP
IB BUS line
DOWN :
UP :
Common :
C

Using:
3
Do not forget to mount the
protection cover to separate
the BUS line and the power
supply.
This switch allows to isolate theCENTRALIS uno IB VBfrom the BUS line.
The brief commands coming from the BUS line control the CENTRALIS uno IB VB.
The commands coming from the BUS line are disabled, but you can force the control the CENTRALIS uno IB VB if you hold the
command for more than 2 secs.
➜ The LED of the CENTRALIS uno IB VB lights on in red.
Mounting
FRONT PLATE CONTROL UNIT FRAME BRACKET PROTECTION COVER
®
WALL
Operating mode
UP key
0/auto
switch
LED
The CENTRALIS uno IB VB offers two different operating modes.You can visualise the selected mode at the power on of the
CENTRALIS uno IB VB.
EU mode : the red LED blinks one time.
US mode : the red LED blinks twice.
The CENTRALIS uno IB VB has three keys ( ) to control the blind individually and has also a BUS line input to
connect a master control with a CENTRALIS IB (see page 4).
EU mode :
• To raise or lower the blind, press and hold (>2 sec.) the correspondings keys ( or )
• To tilt the slats, press briefly the correspondings keys ( or )
• To stop the blind, press the stop key ( )
US mode :
• To raise or lower the blind, press briefly the correspondings keys ( or )
• To tilt the slats, press and hold (>2 sec.) the correspondings keys ( or )
• To stop the blind, press the stop key ( )
The functioning is the same for the EU and US modes.
• To raise or lower the blind, press briefly the correspondings keys ( or )
• To stop the blind, press the stop key ( )
• No tilting function.
DOWN
key
STOP/IP
key
“0 / auto”switch
Individual commands
Master commands The configuration can be changed by
pressing for more than 5 secs. on the
stop key ( ) of the CENTRALIS
uno IB VB just after the power on.
Change the EU/US configuration
"Auto" position
"0" position

®
• Raise the blind at its UP limit
with the key.
1
• Push simultaneously on the
and keys until the LED lights
on in “green”.
The blind begins to move down.
• Stop the blind at the interme-
diate position you wish with
the key.
If necessary,adjust this position
with the keys.
• Push the key more than 2
sec.
➭The LED lights off, the CEN-
TRALIS Uno IB VB has memorized
the intermediate position.
2 3
• Push simultaneously on the
and keys until the LED lights
on in “green”.
The blind momentarily moves up.
• Adjust the right tilt angle with
the keys. • Push the key more than 2
sec.
➭The LED lights off, the CEN-
TRALIS Uno IB VB has memorized
the tilt angle.
4
during
2 seconds
after
3 seconds
STOP IP
567
after
3 seconds
during
2 seconds
With the CENTRALIS uno IB VB, it is possible to program an intermediate position (IP) and an automatic opening of the slats
at this position.
Principle : the CENTRALIS uno IB VB records the timing for the venetian blind to go from the starting position to the interme-
diate position you wish to program.
Threfore,the intermediate position must be set from the UP limit of the venetian blind in order to always get the same adjust-
ment.
Non-binding document. Products and references in this document are subject to change without prior notice.Please consult SOMFY before using such references.© SOMFY 09/00
To reach the right intermediate position preset, the blind must be at its UP limit.
• Press briefly the key.
➭The blind moves down, stops at the intermediate position and the slats tilts at the preset
angle.
Be careful :
• if you reach the IP after an UP command but not from the UP limit, the blind will not
stop at the right preset intermediate position, but the slats will tilt.
• if you reach the IP after a DOWN command (ie : blind at the DOWN limit), you will
only get the tilting of the slats.
during
8 seconds
Reach the intermediate position, then press
and hold the STOP for more than 8 secs. until
the led lights on in “red”.
➭The intermediate position and the tilt set-
ting are deleted.
Note : The intermediate position can only be recorded and reached by the local push buttons.
Intermediate position / automatic slats tilting
Setting of the intermediate position
Setting of the automatic opening of the slats
Using Delete the intermediate position
IP
adjust the
angle
UP limit
UP limit
orientation
Green
Green
Red

3 x 0,75 mm2
IB BUS line 3 x 0,75 mm2
IB BUS line 3 x 0,75 mm2
IB BUS line
CENTRALIS IB CENTRALIS UNO IB VB CENTRALIS UNO IB VB
MAINS
230V - 50Hz
3 wires x 1,5 mm2
3 wires x 0,75 mm2
3 wires x 0,75 mm2
5 wires x 1,5 mm2
5 wires x 1,5 mm2
4 wires x 0,75 mm24 wires x 0,75 mm2
Neutral
Earth
Phase
MAINS
230V - 50Hz
3 wires x 1,5 mm2
Neutral
Earth
Phase
+
NL
N
+
+
-C
123456
NL
N
123456
Centralis uno IB VBJunction box MotorSupply
Phase Neutral Earth Earth (green/yellow)
Common (blue) Up (black or brown) Down (black or brown)
L➜ N➜ N ▲ ▼ +
Centralis IB
C
1 2 3 4 5 6
CABLING OF SEVERAL CONTROL POINTS FOR SEVERAL BLINDS
CENTRALIS uno IB VB with CENTRALIS IB
®
Set the switch of the CENTRALIS IB on the “+” position.