SOMFY Pergola Instruction manual

Drive Power
BLU
C
-
24 Vdc - 3A/5.5A
Selected via Dip Switch 3
BRN
D
+
Encoder Signal
Rain Sensor
O
Contact Dry contact input
P
Common
Q
Power supply output:
24 VDC 300 mA
R
S1 S2
Encoder Power
F
BLU
M
-
BRN
N
+
BLK
G
-
RED
H
+
RED
I
-
BLK
J
+
YEL
E
Encoder Requires Dip
GRN
F
YEL
K
GRN
L
Switch 1 ON
-
+
Copyright © Somfy SAS 12/2019 P-0036
Pergola Tilt RTS Control Box
Connection Quick Start Guide
S T
External
antenna
PROG
button
+
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
Switch 1
Switch 2
Switch 3
Switch 4
Switch 5
O P
Q
R
Power
Output
Contact
B
A
Drive
S2
Drive
S1
E
D
C
Power
supply
input
External antenna
S
Signal Conductor
T
GND Shielding braid
+
-
Status
The LED ashes every 4 seconds: Circuit board waiting.
The LED ashes rapidly: Command in progress.
Fault
The red LED light remains illuminated for 5 seconds: Current consumption threshold has
been exceeded or circuit board has heated up too much during an output command.
The red LED ashes: drive synchronisation fault.
The orange LED remains illuminated for several seconds: Backing-up the memory.
The orange LED ashes rapidly: Movement of a drive not permitted by a sensor action.
Wind
The orange LED remains illuminated: Wind
threshold has been exceeded.
The orange LED ashes rapidly: protection still
in progress for 15 minutes ater the threshold
last being exceeded.
Temperature
The orange LED remains illuminated: the ice threshold has been
exceeded. The Control is locked.
The orange LED ashes rapidly: protection still in progress for 15
DESCRIPTIONS OF CIRCUIT BOARD INDICATOR LIGHTS
1
2
34
S
T
Rain
The orange LED remains illuminated: The rain threshold has been
exceeded.
The orange LED ashes rapidly: protection still in progress for 15
minutes ater the threshold last being exceeded.
BEFORE YOU BEGIN: Power must be cut before wiring, setting the Dip Switches or making any wiring changes
OUTPUT Vdc
+
-
POWER SUPPLY
OUTPUT Vdc
+-
S1
+
-
S2
+
-
Status
Fault
Wind
Rain
Temperature
Input Power Supply
A
-
24 Vdc power supply
B
+input (SELV)
Switch 1
ON Drive with encoder sensor
OFF Drive
without encoder sensor
Switch 2 (Requires Switch 1 ON)
ON
Activates synchronization S1 and S2
OFF
Deactivates synchronization S1 and S2
Switch 3
ON 5.5 A max. per output
OFF 3 A max. per output
Switch 4
ON Activates the temperature sensor
OFF
Deactivates the temperature sensor
Switch 5
ON Close in the event of wind
OFF Open in the event of wind
DESCRIPTION & CONNECTIONS
minutes after the latest threshold is exceeded. Sensors locked out.
F
G
H
E F M
N
I J K L
+
-
Contact
Rain
Sensor
DIP

Pergola Tilt RTS Control Box
Programming Quick Reference Guide
Copyright © Somfy SAS 12/2019 P-0036
1. INITIATE PROGRAMMING
OR
2. CHECK THE DIRECTION OF OPERATION
3. SET THE END LIMITS 4. SNOW/ICE POSITION AND VALIDATION
5. PAIRING THE REMOTE CONTROL
1.1 Press & hold the PROG button
on the circuit board until both S1 and
S2 LEDs ash. The motor jogs.
2.1 Press the UP button to conrm the pergola opens.
3.1 Run the motor to the desired open
position.
3.2 Press briey the MY and DOWN.
Do not interrupt the movement:
the control will automatically
detect the in limit.
4.1 Use the UP or DOWN buttons to run the motor to the desired position for
ice/snow. (This position must be set even if Dip Switch 4 is off)
4.2 Press & hold the MY button until the motor jogs to conrm the settings.
Briey press the PROGRAMMING
button on the back of the
transmitter.
The motor jogs.
NOTE: On a multi-channel RTS control,
select the desired channel on step 1.3
ADD OR DELETE A CONTROL OR SENSOR
The procedure to delete a RTS control or sensor is the same.
The direction
of rotation is
correct
If the pergola closes, the direction of rotation is incorrect.
2.2 Press & hold MY button until the motor jogs.
The rotation direction has been modied.
1.3 If on a multi-channel RTS
control, select the desired channel.
1.4 Press briey UP and DOWN
simultaneously. The motor jogs.
1.2 Briey press the PROG button to select motor S1
or S2 to program. S1 or S2 LED will blink to conrm the
motor to be programmed.
6. PROGRAMMING MOTOR 2
a) Press & hold the PROG button on
the back of Control 1 until the pergola
jogs.
b) Briey press the PROG button on
the back of Control 2 until the pergola
jogs.
CONTROL 1: Previously
programmed control
CONTROL 2: Second control to
be added or deleted.
BEFORE YOU BEGIN: Conrm the Dip Switches are set to the correct position and all wiring is done.
To completely clear
the control’s memory:
RESETTING THE CONTROL
BOX TO FACTORY MODE
> 7 s.
Press the PROG button on the circuit
board for more than 7 seconds until all
the indicator lights on the circuit board
light up.
The motor will run to the in (closed) limit.
MY
Repeat steps from 1.2 through step 4.