SOMFY Axroll User manual

CONTROL BOX
FOR ROLLING GARAGE DOORS WITH
RADIO MODULES FOR SAFETY EDGE
AxrollNS
Ref. 5047695
ARMOIRE DE COMMANDE
POUR PORTES ENROULABLES AVEC
MODULES RADIO POUR BARRE PALPEUSE

2
24 V
ac/dc
0 V C NC NO
12345
24 V
ac/dc
0 V
12
ATEST2
PROG
COMR2R112/24V
ac/dc
+-
ATE ST 1
PROG

3
English
■Characteristics
Power supply 220-240 Vac / 50-60 Hz
Fuse 250 Vac / 5 A - AF
Motor power 230 Vac 750 W
Protection rating IP 55
Ambient operation temperature -15 à +55 °C
Radio frequency 433,42 MHz
Accessories power 24 Vcc
Resistive safety edge 4 Kæ< R < 12 Kæ
Max. current for accessories 0,33 A / 8 W max
Signal light 24 Vdc, 10 W max / 230 Vac, 40 W max
Area lighting 250 Vac, 500 W max
Auxiliary output Contact NO / 250 Vac, 500 W max
Operating Class I
Number of max. channels 32
Radio range for safety edge modules 10 m
Radio frequency for safety edge modules (bi-directional) 868.90 MHz
Installation
180
90
230
65
35
53
■Dimensions
■Description The AXROLL receiver is used to control a rolling garage door fitted with
a 230V motor with integrated mechanical endstops. The Axroll is
compatible with the Somfy RTS range of controls. Additionnally to the
radio safety edge (resistive), numerous safety and signaling devices can
be connected to the AXROLL (photocells, signal lights, area lighting).
This product complies with the standard EN60335-2-95. When installed
as recommended in this instruction manual and in accordance with
regulations in force, the system controlled by the Axroll will comply with
EN 13241 and EN 12453 standards. By ignoring these instructions,
Somfy will not be responsible for any resultant damage caused. The
Axroll must be installed inside the garage and connected to a motor
equipped with a manual over-ride system (LT CSI).
Hereby, SOMFY, declares that this product (AXROLL) is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of
Conformity is available at the web address www.somfy.com/ce (Axroll NS radio safety edge).
In mm.

4
■Programming
Parameter
scroll buttons
Value scroll buttons
The Axroll is factory configured with default settings corresponding to the
requirements of the installation.
The remote controls require programming.
The Axroll operational parameters can be adjusted to create a
personalised control scenario corresponding to the accessories which
have been connected (see complementary parameters p. 8).
The Axroll parameters can be defined during the
installation process in any order of preference.
Use the or buttons to browse the menu and
display the parameter required.
Use the or buttons to change the value of the
parameter.
The last value is recorded automatically (the display is
fixed when pressing the buttons).
Ensure that the motor end-limits have been commissioned
before adjusting the Axroll parameter settings.
Preset parameters
(in factory)
0:4
Operating parameters
Functioning mode: “SEQUENTIAL” = 02
Security input for safety edge enabled when closing
the door = 02
No accessory connected to security input 2 = 00
No accessory connected to security input 3 = 00
Safety action of the door upon closing (stop and then
total reopening of the door) = 01
Self-test for accessory with TEST input = 02
No self-test for security input 2 = 00
No self-test for security input 3 = 00
Auxiliary accessory
parametering
Contact to drive a zone lighting and an orange light
with integrated blinker (required if access giving on the
public highway).
= 04
Remote control
programming
Recording
remote controls
Press the remote control button to
program and the button on the
Axroll simultaneously for 3 seconds
until dashes appear.
The control is now recorded.
3 sec.
Deleting the
remote controls
Delete all remote controls by
pressing and holding the button
for 3 seconds until dashes appear.
All controls have been removed.
3 sec.

5
Always return to parameter with key or .
Your door is in operating condition.
Parameter functioning
Motor operating time
Each press on the or button adjusts the time in
1 second increments.
Examples:
- 20 seconds for height of door up to 2500mm
- 23 seconds for height of door between 2500mm and 3000mm
- 30 seconds for height of door between 3000mm and 4000mm
= 80
20
23
30
Time for reclosing the door
Inactive parameter in the sequential mode. = 05
Time before motor reversion
Each press on the or button adjusts the time in
1 second increments.
00: the door re-opens immediately in the event of an
obstacle detection.
= 00
Area lighting time after cycle end
Each press on the or button adjusts the time of
1 minute increments (10 minutes max.)
= 02
■Operating
information
The LCD screen will provide a visual indication providing rapid diagnosis
relating to the operating modes of the Axroll.
Event codes
Axroll waiting for a command
Opening door
Delay before closing the door
Closing door
Open cell hidden
Close cell hidden
ADMAP cell hidden
Door movement forced by keypad
Emergency stop triggered
Self-testing safety
Permanent contact on “START” input
Delay before motor reversion
Fault codes
Safety fault at opening (contact always open)
Safety fault at closing (contact always open)
ADMAP safety fault (contact always open)
Self-test failed on security input 1
Self-test failed on security input 2
Self-test failed on security input 3
Limit exceeded on 24V power supply
(too many accessories connected)
Operating time "T0" too short or
motor end-limit not reached
English

6
■Operating
information (cont’)
Cycle counters
Tens and units
Thousands and hundreds
Hundred and tens of thousands
Accessories
consumption Power consumed in Watts (from 00 to 99)
Log of the last
10 faults
.... : see faults codes above.
To clear the fault codes, select the parameter
press and hold the button for 3 seconds until
dashes appear .
For the fault codes from to :
Once the fault is corrected, there is no need to clear
the log fault code to return to normal operation.
For defect codes from to :
Once the fault is corrected, you must
clear the log defect code to return to
normal operation.
....
Functioning Modes
Automatic Mode (safety accessories are required)
Semi-Automatic Mode
Sequential Mode
Sequential Mode +Time out
(safety accessories are required)
3-buttons Mode (Up - Stop - Down)
Forced mode (Safety devices are deactivated)
= 00
01
02
03
04
05
Security Input 1
(Safety Edge)
No safety edge connected
Active when opening the door
Active when closing the door
Active when closing the door + prevents the door
opening
Contact for connecting an emergency stop device
= 00
01
02
03
04
Security Input 2
(Photocells)
No accessory connected
Active when opening the door
Active when closing the door
Active when closing the door + prevents the door
opening
Contact for connecting an emergency stop device
= 00
01
02
03
04
■Parameter list

7
■Parameter list
(cont’)
Security Input 3
No accessory connected
Active when opening the door
Active when closing the door
Active when closing the door + prevents the door
opening
Contact for connecting an emergency stop device
= 00
01
02
03
04
Safety Action of the
door upon closing
Stop
Stop and then total re-opening
Stop and then partial re-opening
= 00
01
02
Configuration of the
safety edge self-test
connected to security
input 1
No self-test
Self-test by cutting the power supply
Self-test for accesory with TEST INPUT
Self-test for resistive safety edge
Self-test for optoelectronic safety edge
Self-test for ultra-sonic safety edge
= 00
01
02
03
04
05
Configuration of the
accessory self-test
connected to security
input 2
No self-test
Self-test by power supply cutting
Self-test for accesory with TEST INPUT
= 00
01
02
Configuration of the
accessory self-test
connected to security
input 3
No self-test
Self-test by power supply cutting
Self-test for accesory with TEST INPUT
= 00
01
02
Remote control
programming
You can not mix
sequential mode
and 3-button mode
Sequential, automatic,
semi-automatic mode
Opening/Closing
Control of the auxiliary output
= 00
03
3 button mode
Opening
Closing
Stop
Control of the auxiliary output
= 00
01
02
03
or
English

8
■Programming
the radio safety
edge modules
The radio safety edge modules are
factory pre-programmed. This procedure
is only required when re-programming
the modules.
Open the AxrollNS and transmitter module
boxes.
Press the receiver “PROG” (1) button for 1s.
A short ‘beep’ will be heard.
Press the transmitter “PROG” (2) button.
The receiver confirms the programming with a
short ‘beep’ (3).
This procedure must be completed within
10 seconds, or the receiver will drop out of the
programming mode (2 x short ‘beep’ signals).
PROG
ATEST2
PROG
COMR2R112/24V
ac/dc
+-
ATES T1
1
2
3
■Replacing
the radio safety
edge transmitter
battery
The radio safety edge transmitter will emit
4 short ‘beep’ signals every 20 seconds, when
the battery is low of charge.
Remove the transmitter cover.
The batteries are mounted on the underside of
the cover.
Replace the existing batteries with new ones,
taking care to insert the new batteries in the
correct polarity indicated by the connector.
Battery type: 2 x 1.5V LR03 AAA
Battery life: 2 years
■Parameter list
(cont’)
Configuration of the
accessories connected
to the auxiliary output
Contact to drive an electric latch (the latch must be
supplied with an independant power supply)
Contact to drive an electromagnetic latch
Contact to drive an signal light without delay
(only during the door’s operation)
Contact to drive an signal light without delay
(before starting and during door’s operation)
Contact to drive area lighting
(automatic cut off after delay t3)
Contact to drive an open door indicator
Contact of the stable mono relay
to drive an automation system
Contact of the bi-stable relay
to drive an automation system
= 00
01
02
03
04
05
06
07

9
■Caractéristiques
Alimentation générale 220-240 Vac / 50-60 Hz
Fusible de protection 250 Vac / 5 A - AF
Puissance moteur 230 Vac 750 W
Indice de protection IP 55
Température d’utilisation -15 à +55 °C
Fréquence radio 433,42 MHz
Alimentation accessoires 24 Vcc
Résistance barre palpeuse 4 Kæ< R < 12 Kæ
Courant maximum accessoires 0,33 A / 8 W max
Feu orange 24 Vdc, 10 W max / 230 Vac, 40 W max
Eclairage de zone 250 Vac, 500 W max
Sortie auxiliaire Contact NO / 250 Vac, 500 W max
Classe d’utilisation I
Nombre de canaux 32
Portée radio modules barre palpeuse 10 m
Fréquence radio modules barre palpeuse (bi-directionnelle) 868,90 MHz
Installation
■Description Le récepteur AXROLL permet de commander à distance une porte de
garage enroulable équipée d’un moteur 230V à fins de course
mécaniques integrés à l’aide d’émetteurs KeytisNS 2/4 RTS et du bouton
poussoir radio RTS. En plus de la barre palpeuse (résistive) radio,
différents systèmes de sécurité et de signalisation peuvent être
connectés sur l’AXROLL (barre palpeuse, cellules photo-électriques, feu
clignotant, éclairage de zone).
Ce produit est conforme aux dispositions relatives aux armoires de
commande de la norme EN 60335-2-95. Installé selon les présentes
instructions et avec le respect des diverses exigences réglementaires, Axroll
permet une installation conforme aux normes EN 13241 et EN 12453. Dans
le cas de non-respect de ces instructions, Somfy se libère de toute
responsabilité des dommages qui peuvent être engendrés. Axroll doit être
installé à l’intérieur du garage avec un moteur à commande de secours
intégrée (LT CSI).
Nous, SOMFY, déclarons que ce produit est conforme aux exigences essentielles et autres
dispositions pertinentes de la directive 1999/5/EC. Une déclaration de conformité est mise
à disposition à l’adresse internet www.somfy.com/ce (Axroll NS radio safety edge).
180
90
230
65
35
53
■Encombrement
En mm.
Français

10
■Paramétrage
Touches de défilement
de paramètres
Touches de défilement
de valeurs
Le boîtier de commande Axroll est configuré en usine avec les
paramètres par défaut correspondant à la majorité des installations. Il ne
reste qu’à appairer la télécommande et le système fonctionne.
Néanmoins, il peut être entièrement et facilement configuré afin d’obtenir
un fonctionnement optimal correspondant aux types d’accessoires qui
lui sont raccordés ainsi qu’au mode de fonctionnement souhaité par
l’utilisateur (voir paramètres complémentaires p.6).
Les différents paramètres proposés ne sont pas
obligatoires et il n’y a pas d’ordre à respecter pour
naviguer dans les menus.
Les touches ou permettent de naviguer dans
le menu et d’afficher le paramètre voulu.
Les touches ou permettent de modifier la
valeur du paramètre. La dernière valeur est
automatiquement enregistrée (l’affichage est fixe
pendant l’appui sur les touches).
Avant toute intervention sur les paramètres, les fins de
courses du moteur doivent être réglés.
Paramètres définis par
défaut (en usine)
0:4
Paramètres de
fonctionnement
Mode de fonctionnement “SEQUENTIEL” = 02
Entrée sécurité barre palpeuse active en fermeture = 02
Pas d’accessoire raccordé sur entrée sécurité 2 = 00
Pas d’accessoire raccordé sur entrée sécurité 3 = 00
Action de sécurité à la descente
(arrêt puis ré-ouverture totale) = 01
Auto-test pour accesoire muni d’une entrée TEST = 02
Pas d’auto-test sécurité 2 = 00
Pas d’auto-test sécurité 3 = 00
Paramétrage des
accessoires auxiliaires
Permet le pilotage d’un éclairage de zone et d’un feu
orange à clignoteur intégré (obligatoire si accès
donnant sur la voie publique).
= 04
Paramétrage des
télécommandes
Ajout de
télécommande
Appuyer simultanément sur la
touche de la télécommande à
programmer et sur la touche
pendant 3 secondes jusqu’à
l’apparition des tirets sur l’afficheur.
3 sec.
Effacement des
télécommandes
(si besoin)
Effectuer un appui maintenu
sur la touche pendant
3 secondes jusqu’à l’apparition des
tirets sur l’afficheur.
3 sec.