SOMFY Sonesse 50 RTS User manual

Sonesse®50 RTS
Ref. 5106210A
Installation guide
Notice d’installation
Guida all’installazione
Guía de instalación
ES FR EN
IT

Por la presente, Somfy declara que el producto cumple con los requisitos básicos y demás disposiciones
de la directiva 1999/5/CE. Podrá encontrar una declaración de conformidad en la página web www.
somfy.com/ce. Aplicable para la UE, Suiza y Noruega. Fotos no contractuales.
Los productos y baterías eléctricos dañados no deben desecharse junto con la basura doméstica
normal.Asegúrese de depositarlos en contenedores especialmente designados para ello o diríjase
a una organización autorizada que garantice su reciclaje
EN
FR
IT
ES
Somfy hereby declares that this product conforms to the essential requirements and other relevant
provisions of Directive 1999/5/CE. A Declaration of Conformity is available at www.somfy.com/ce.
Usable in EU, CH and NO. Images are not contractually binding
Damaged electric products and batteries should not be disposed of with normal household
waste. Make sure to drop them in specially provided containers or at an authorized
organization that will ensure they are recycled.
Par la présente, Somfy déclare que l’appareil est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE. Une déclaration de conformité est mise à disposition
à l’adresse internet www.somfy.com/ce. Utilisable en UE, CH et NO. Images non contractuelles.
Les produits électriques et électroniques endommagés tout comme les piles usagées ne doivent
pas être jetés avec les ordures ménagères.Veiller à les déposer dans un point de collecte ou dans
un centre agréé an de garantir leur recyclage.
Somfy dichiara che il dispositivo è conforme ai requisiti essenziali e alle altre disposizioni pertinenti
della direttiva 1999/5/CE. Una dichiarazione di conformità è disponibile all’indirizzo Internet www.
somfy.com/ ce. Utilizzabile in UE, CH e NO. Le immagini hanno uno scopo puramente indicativo.
I prodotti elettrici danneggiati e le batterie esauste non devono essere smaltiti insieme alla normale
immondizia domestica.Devono essere smaltiti all’interno di contenitori speciali appositi o portati
presso un’organizzazione autorizzata che ne garantirà il riciclaggio.

3
© 2013 Somfy SAS. All rights reserved. 12/2013
EN
CONTENTS
1. Introduction 3
2. Safety 4
2.1. Safety and responsibility 4
2.2. Specic safety advice 4
3. Installation 5
3.1. Motor preparation 5
3.2. Tube preparation 5
3.3. Motor/tube assembly 5
3.4. Mounting the motorized tube on the
brackets 5
4. Wiring 6
5. Commissioning 6
5.1. Programming the RTS transmitter 6
5.2. Checking the rotation direction 6
5.3. Adjusting the end limits 7
5.4. Recording the RTS transmitter 7
5.5. Favorite position: MY position
Recording MY position. 7
6. Operation 8
6.1. Standard operation 8
6.2. Operating with a Somfy sensor or
automatic function 8
7. Additional setting 9
7.1. Favorite position: MY position 9
7.2. End limit re-adjustement 9
7.3. Replacement of a lost remote control 10
7.4. Adding/Deleting RTS transmitter 10
7.5. Adding/Deleting RTS sensors 11
7.6. Erase the memory of the motor 11
8. Troubleshooting 12
8.1. Question on the Sonesse®50 RTS? 12
9. Technical data 12
1. INTRODUCTION
The Sonesse®50 motor range can motorise all tubular applications: Roller shades, Roman shades,
Projection screens, ...
The Sonesse®50 is designed to ensure quiet operations.

4© 2013 Somfy SAS. All rights reserved. 12/2013
EN
2. SAFETY
2.1. Safety and responsibility
• This Somfy product must be installed by a professional motorisation and home automation
installer, for whom these instructions are intended.
• Before installation, check that this product is compatible with the associated equipment and
accessories.
• These instructions describe how to install, commission and use this product.
• Moreover, the installer must comply with current standards and legislation in the country in which
the product is being installed, and inform his customers of the operating and maintenance
conditions for the product.
• Any use outside the sphere of application specied by Somfy is not approved. Such use, or any
failure to comply with the instructions given herein will invalidate the warranty, and Somfy refuses
to accept liability.
Subject to technical modications.
2.2. Specic safety advice
In addition to the safety instructions described in this guide, be sure to also observe the
instructions set out in the attached document "Safety instructions to follow and keep".
1) Switch off the mains supply of the shade before
performing any service operation in the vicinity.
To avoid damaging the product:
2) Never immerse it in liquid!
3) Avoid impacts!
4) Do not drop it!
5) Never drill holes in it!
6) Avoid moving the shade if ice has formed on it.
1
3
5 6
2
4
OFF

5
© 2013 Somfy SAS. All rights reserved. 12/2013
EN
1) Fit the crown (a) and drive wheel (b) to the motor.
2) Measure the length (L) between the end of the drive
wheel and the head end.
1) Cut the tube to the required length.
2) Deburr the tube and remove the debris.
3) For smooth roller tubes, cut a notch with the
following measurements:
e = 4 mm / 0.16 In h = 28 mm / 1.1 In
1) Slide the motor into the tube.
For smooth roller tubes, position the notch previously
cut on the crown.
2) Fix the tube to the drive whell with 4 self-tapping
screws with a diameter of 5 mm or 4 steel pop rivets
with a diameter of 4.8 mm located at L - 15 mm ± 3 mm.
Warning: The screws or pop rivets must only be
attached to the drive wheel and not to the motor.
If necessary, screw the bracket interface on the motor
head.
1) Mount the motorized tube on the end bracket (c).
2) Mount the motorized tube on the motor bracket (d).
Fit the stop ring (e).
3. INSTALLATION
ab
Ø>47mm
c
d
e
ehe
h
ab
Ø>47mm
c
d
e
ehe
h
Ø > 47
eh
Ø > 47
eh
Ø > 47
eh
ab
Ø>47mm
c
d
e
ehe
h
ab
Ø>47mm
c
d
e
ehe
h
ab
Ø>47mm
c
d
e
ehe
h
ab
Ø>47mm
c
d
e
ehe
h
3.1. Motor preparation
3.2. Tube preparation
3.3. Motor/tube assembly
3.4. Mounting the motorized tube on the brackets
1
2
1 2
3
1
2
1
2

6© 2013 Somfy SAS. All rights reserved. 12/2013
EN
4. WIRING
1) Cut off the mains power supply.
2) Connect the motor according to the information in
the table below:
3 x 0.75 mm2
3 x 1,5 mm2
1
2
3
RANGE Neutral Live Earth
230V-50Hz Blue Brown Yellow/
Green
220V-60Hz
120V-60Hz White Black Green
100V-50/60Hz
5. COMMISSIONING
1) Switch on the power supply.
2) Press the UP and DOWN buttons simultaneously
on the RTS transmitter: the shade jogs (moves up and
down briey) and the transmitter is preprogrammed in
the motor
1) Press the RTS transmitter UP button:
a) If the shade is raised (a), the rotation direction is
correct: move to the section entitled «Adjusting the end
limits».
b) If the shade is lowered (b), the rotation direction is
incorrect: move to the next step.
2) Press the RTS transmitter MY button until the shade
jogs: the rotation direction has been modied.
3) Press the RTS transmitter UP button to check the
rotation direction.
a
b
=
=
1
32
5.1. Programming the RTS transmitter
5.2. Checking the rotation direction
1 2

7
© 2013 Somfy SAS. All rights reserved. 12/2013
EN
The limits can be set in any sequence.
1) Press and hold the UP button to move the shade
to the desired Up position. If necessary adjust the Up
position, using the UP or DOWN buttons.
2) Press the MY and DOWN buttons simultaneously
and release them once the shade begins to move. The
up limit is memorized.
3) Press the MY button when it reaches the desired
Down position.
If necessary adjust the down position, using the UP or
DOWN buttons.
4) Press the MY and UP buttons simultaneously and
release them when the shade begins to move.
The Down limit is memorized. The shade moves up and
will stop at its upper limit.
5) To conrm the end limits press and hold the MY
button until the shade jogs.The end limits are recorded.
After recording the end limits:
Briey press the programming button on the back of
the transmitter. The shade jogs.
The transmitter is recorded.
OR
1) Switch off the power supply.
2) Switch on the power supply. The shade jogs.
3) Simultaneously press the UP and DOWN buttons on
the RTS transmitter. The shade jogs.
4) Briey press the programming button on the back of
the transmitter. The shade jogs.
The transmitter is recorded.
To set the MY position, move the shade to the desired
position with the UP or DOWN button then press the
MY button until the shade jogs.
1 2
34
5
PROG.
1 2
3 4
PROG.
5.3. Adjusting the end limits
5.4. Recording the RTS transmitter
5.5. Favorite position: MY position / Recording MY position

8© 2013 Somfy SAS. All rights reserved. 12/2013
EN
6. OPERATION
Up, Down, My
1) To move the shade from a limit to the other limit,
briey press the UP or DOWN button.
2) To stop the shade, press the MY button.
3) To move the shade to the MY position, briey press
the MY button.
6.2.1. Operating with a Somfy sun sensor
To activate this function, you need a Telis Soliris
transmitter. By default, the Sun function is not active.
1) To activate the Sun function, press the SELECT
button on the Telis Soliris transmitter until the shade
jogs.
2) To disactivate the Sun function, press the SELECT
button on the Telis Soliris transmitter until the shade
jogs.
When the intensity of the daylight exceeds the
threshold set by the Sunis sensor RTS, an order is
sent to the shade after 2 min.
The shade goes to the MY position or to its down limit
if no MY position has been memorised.
When the intensity of the daylight falls below the
threshold set by the Sunis sensor RTS, the shade goes
to its Up limit after a delay of 15 to 30 minutes.
6.2.2. Operating with a Somfy wind sensor
Reaction of the screen to the wind rising.
When the wind rises, the screen will start to move up
to the upper end limit. It is impossible to prevent the
screen from closing, or to lower it while the wind is still
blowing.
Reaction of the screen to the wind dropping.
When the wind has dropped, a manual down order
may be issued via the RTS control point after 30
seconds. However, all automated systems will remain
locked for 11 mins.
We suggest not to pair a wind sensor to the motor
when used to motorize interior window coverings. The
motor will react in priority to the wind sensor orders,
functionning not adapted to interior window coverings.
1
2
3
OK
onoff
onoff
onoff
onoff
1
2
30 s
30 s
6.1. Standard operation
6.2. Operating with a Somfy sensor

9
© 2013 Somfy SAS. All rights reserved. 12/2013
EN
7. ADDITIONAL SETTING
7.1.1. Changing the MY position
To change the MY position go to the new desired MY
position with the UP and DOWN buttons then press the
MY button until the shade jogs.
7.1.2. Deleting the MY position
To delete the MY position, press the MY button to
move to this position and press the MY button until the
shade jogs.
Readjusting the upper end limit
1) Press the UP button, to move the shade to the limit
to be readjusted.
2) Press and hold the UP and DOWN buttons
simultaneously until the shade jogs.
3) Press and hold the UP or DOWN button to move the
shade to the new desired position.
4) To conrm the new limit press and hold the MY
button until the shade jogs.
Readjusting the lower end limit
1) Press the DOWN button to move the shade to the
limit to be readjusted.
2) Press and hold the UP and DOWN buttons
simultaneously until the shade jogs.
3) Press and hold the UP or DOWN button to move the
shade to the new desired position.
4) To conrm the new limit press and hold the MY
button until the shade jogs.
1
2
1 2
34
1 2
34
7.1. Favorite position: MY position
7.2. End limit re-adjustement

10 © 2013 Somfy SAS. All rights reserved. 12/2013
EN
This reset deletes all transmitters programmed, but
end-limits, intermediate position and sensors are
retained.
Only switch off the current for the motor to be reset!
1) Cut the power supply for 2 seconds.
2) Switch the power supply back on for 10 to 15
seconds.
3) Cut the power supply for 2 seconds.
4) Switch the power supply back on: the shade moves
during 5 seconds (If the shade position is an end limit,
the behavior of the shade will be a jog).
5) Press the RTS transmitter (B) PROG button until the
shade jogs: all the RTS transmitter are cleared and the
new RTS transmitter is programmed in the motor.
Find a RTS transmitter programmed in the motor.
Press and hold the programmed RTS transmitter’s
(A) PROG button until the shade jogs: the motor is in
programming mode.
Press briey the RTS transmitter (B) PROG button to
add or delete this transmitter: the shade jogs and the
RTS transmitter is programmed or deleted from the
motor.
A
PROG.
B
2 sec 10 to 15
sec
2 sec
1 2
3
5
4
PROG.
A
PROG.
B
C
A
B
A
A
A
B
B
CC
PROG.
A
PROG.
B
A
A
A
A
PROG.
A
PROG.
A
PROG.
C
PROG.
C
+
-
7.3. Replacement of a lost remote control
7.4. Adding/Deleting RTS transmitter