Sony PCS-XG100 Instruction Manual

Select from History
Previous
Enter Number/Address
Select from Phone Book
Connect
IP:192.168.0.11 5/11/2008 13:00
Detailed Dial
Dial to:
Line I/F
Communication
Bit Rate
Number of Lines
Home
1Mbps
IP
1B (64K)
SaveConnect Cancel
History
Phone Book
Connect
Camera
5/11/2008 13:00IP:XXX.XXX.XXX.XXX
Home
AAA
Ready
1. To begin with 2. Let’s connect
Press ENTER after each selection to proceed.
1
Select “Connect.”
2
Select “Enter Number/
Address.”
3Select the Line I/F. 
The Line I/F
cannot be selected
depending on the
system setup.
Connect
Camera
5/11/2008 13:00IP:XXX.XXX.XXX.XXX
Home
AAA
Ready
4Enter the IP address or ISDN line
number of a remote party.
5Select “Connect” and press
ENTER, or press .
The number is dialed, and the
system establishes connection.
 ISDN will be supported in version 1.41 and later.
Turn on your HD Visual Communication System and TV monitor,
and check the following to ensure that connection is possible.
Is the picture of your camera (local picture) on the monitor screen?
Is the IP address of the local system or the ISDN line number
displayed?
Notes:
Connection to a remote party is not possible if neither the IP address
ˎ
nor ISDN line number is not displayed.
You can hide the IP address of the local system using the setup menu.
ˎ
Main indicators that appear during
communication
Controlling a remote camera.
Local microphone is turned off.
Presentation (transmission) is being executed.
Presentation (reception) is being executed.
Local party has drawing rights for annotation
(function for writing on the display via a pen tablet).
1 2 4 5 3
This section describes how to call a remote party that is not registered in the Phone Book.
© 2013 Sony Corporation
HD Visual Communication System PCS-XG100/XG77/XG100S/XG77S
Quick Connection Guide
For details on operations, refer to the Operating Instructions (stored in the supplied CD-ROM).
4-455-812-13 (1)

RFZ

Transmitting a picture for
presentation
You can transmit a picture from the computer connected
to the DVI-I 2 (PC) IN connector to a remote party.
Switching the camera for control
Switch between controlling the local camera or the
remote camera.
Ending the communication and
disconnecting
Switching on/off the local
microphone
Switching the picture on the TV
monitor
Press the LAYOUT button to display the Layout
menu.
0
Terminal
Layout
Screen Display Patterns
Broadcast Mode
Save Cancel
Stop Broadcast
PandPFull
Side by Side PinP
PinPPinPPinPPinP
Select the screen display pattern of the local and
remote pictures using the ///and ENTER
buttons.
Recalling the Preset Camera Angle
Select “Preset” in the Camera menu to display the
Preset Setting List.
Press button 1 to 6 to move the camera to the preset
position.

Selecting the input picture
Press the VIDEO INPUT button to display the Video
Input menu.
Video Input > Near
Save Cancel
CAMERA DVI-I 2DVI-I 1HDMI
Select the video input using the ///and ENTER
buttons.
CAMERA: Video input from the camera connected to
CAMERA connector
HDMI:Video input from the camera or equipment
connected to HDMI IN connector
DVI-I 1: Video input from the equipment connected to
DVI-I 1 IN connector
DVI-I 2: Video input from the equipment connected to
DVI-I 2 (PC) IN connector
This function is not available on the PCS-XG77/XG77S.
For details on operations, refer to the Operating Instructions (stored in the supplied CD-ROM).
“IPELA” and are trademarks of Sony Corporation.
Displaying Camera menu
Press the CAMERA button to display the Camera
menu.
Select the menu item using the ///and ENTER
buttons, and the selected adjustment menu is
displayed.
Adjustments: for angle and zoom adjustments
Brightness: for brightness adjustment
Preset: for presetting and recalling the camera angle
and zoom
Details: for focus adjustment, white balance
adjustment, backlight compensation and digital
zoom function
Remote Commander Guide
Operating the menu
Select the setting item in the
menu displayed on the screen,
and confirm the selection.
Displaying Tools menu
Press the TOOLS button to display the Tools menu.
Select the menu item using the ///and ENTER
buttons, and you can use the selected function such
as “Annotation.”












Adjusting the
sound volume of
the remote party
To increase
the volume
To decrease
the volume
Adjusting the camera angle and
zoom
To enlarge
the picture
To reduce
the picture
RightLeft
Up
To move the camera
angle
Down