Soundoff Signal ETSSLFVBK13 User manual

1.800.338.7337 / www.soundo󰀨signal.com
ETSSLFVBK13_ETSSLFVBK14 1122 REV B
1
AFTERSHOCK SPEAKER BRACKET (NO DRILL) FOR THE CHEVROLET TAHOE PURSUIT &
CIVILIAN 2021 - 2023, FRAME MOUNT
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
ETSSLFVBK13- DRIVER SIDE
ETSSLFVBK14- PASSENGER SIDE
INTRODUCTION:
CONTAINS
ITEM# COMPONENT QTY
1 SPEAKER BRACKET 1
2 SECONDARY BRACKET 1
3 ½” SELF-DRILLING SCREWS 4
4 ¼”-20 HEX HEAD BOLT 2
5 5/16”- 18 HEX HEAD BOLT 1
6 5/16”- 18 LOCK NUT 1
7 5/16” FLAT WASHER 1
8 INSTALLATION INSTRUCTION SHEET 1
9 PRODUCT WARNING CARD 1
10 CA PROP 65 LABEL 1
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and
re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s
Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local
chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
*Speaker and Speaker Hardware Sold Separately
1
2
3
4
5
6
7
ETSSLFVBK13 SHOWN WITH ETSSLF100 SPEAKER*
NOTE: Install done with driver side, ETSSLFVBK13.

1.800.338.7337 / www.soundo󰀨signal.com
ETSSLFVBK13_ETSSLFVBK14 1122 REV B
2
AFTERSHOCK SPEAKER BRACKET (NO DRILL) FOR THE CHEVROLET TAHOE PURSUIT &
CIVILIAN 2021 - 2023, FRAME MOUNT
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
ETSSLFVBK13- DRIVER SIDE
ETSSLFVBK14- PASSENGER SIDE
Fig 2 Fig 3
Fig 4 Fig 5
0.0
0.2
0.4
0.6
0.8
1.0
FRONT VIEW DRIVERS FRAME RAIL
REAR VIEW DRIVER’S FRAME RAIL
INSTALLATION:
1. Remove the skid plate on the underside of the
vehicle just below the front fascia, as shown in
Fig. 1. Consult your local Chevrolet dealer for
recommended disassembly method. Ensure all
safety precautions are followed while working
underneath the vehicle.
2. Remove the Universal Mounting Bracket from
the Aftershock speaker (sold separately) as this
bracket will not be used for installation.
3. Use 4 of the provided self-drilling screws to
attach the speaker bracket to the rear mounting
holes of the Aftershock speaker. Tighten until
screw is fully seated, then tighten to 75 in-lbs.
The speaker should be attached to the bracket in
the orientation shown in Fig. 2. Ensure that the
plug is on the top when in its installed position.
4. With the speaker installed, slide the bracket
assembly on to the frame rail of the vehicle,
as shown in Fig. 3. The tab on the front of the
speaker bracket should line up with the slotted
hole in the vehicle frame.
FIG. 3
FIG. 1
Fig 2 Fig 3
Fig 4 Fig 5
0.0
0.2
0.4
0.6
0.8
1.0
FRONT VIEW DRIVERS FRAME RAIL
REAR VIEW DRIVER’S FRAME RAIL
FIG. 2

1.800.338.7337 / www.soundo󰀨signal.com
ETSSLFVBK13_ETSSLFVBK14 1122 REV B
3
AFTERSHOCK SPEAKER BRACKET (NO DRILL) FOR THE CHEVROLET TAHOE PURSUIT &
CIVILIAN 2021 - 2023, FRAME MOUNT
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
ETSSLFVBK13- DRIVER SIDE
ETSSLFVBK14- PASSENGER SIDE
INSTALLATION (CONT.):
5. Insert the 4” long, 5/16” hex bolt through the
hole in the tab of the bracket and the frame rail,
as shown in Fig. 4. Fasten with the provided at
washer and lock nut on the opposite side of the
frame rail. Tighten until snug. Do not overtighten.
6. Slide the unbent end of the secondary bracket
towards the top of the frame rail opposite the
speaker bracket assembly. Ensure that the
mounting holes of the secondary bracket align
with the mounting anges of the speaker bracket
assembly, as shown in Fig. 5.
7. Fasten the speaker bracket assembly to the
secondary bracket using the provided ¼”-20
bolts. Tighten until snug. Do not overtighten.
8. Plug in the speaker and test to ensure proper
functionality.
9. Reinstall the skid plate according to manufacturer
specications.
FIG. 4
Fig 2 Fig 3
Fig 4 Fig 5
0.0
0.2
0.4
0.6
0.8
1.0
FRONT VIEW DRIVERS FRAME RAIL
REAR VIEW DRIVER’S FRAME RAIL
FRONT VIEW DRIVER’S FRAME RAIL
Fig 2 Fig 3
Fig 4 Fig 5
0.0
0.2
0.4
0.6
0.8
1.0
FRONT VIEW DRIVERS FRAME RAIL
REAR VIEW DRIVER’S FRAME RAIL
REAR VIEW DRIVER’S FRAME RAIL
FIG. 5