Soundoff Signal MPower PMP2BK004 User manual

1
1.800.338.7337 / www.soundo󰀨signal.com
PMPSABK002 1122 REV B
2021-2023 CHEVROLET TAHOE POLICE & CIVILIAN (LS AND Z71 MODELS)
FOR USE WITH THE 3 & 4” STUD MOUNT MPOWER®LIGHTS*
PMP2BK004 - GRILLE MOUNT BRACKET, 2 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and re. Follow crimp connector
manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring conguration and proper integration of
system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local chassis ground (-) must be
sized to supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
CONTENTS
QTY COMPONENT
1 1 MODULE DRIVER SIDE BRACKET
1 1 MODULE PASSENGER SIDE BRACKET
2 RETAINING BRACKET
*mpower Sold Separately
A A
B B
C C
D D
E E
F F
G G
H H
J J
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
21 POL TAHOE Grille Bracket Isheet Images 2 mod
MATERIAL:
REVISION:
DESCRIPTION:
SHEET
2 OF 5
DRAWING NO:
OVERALL ASSEMBLY SHOWN*
INTRODUCTION:
mpower® Fascia Light Features:
• 3” and 4” Stud Mount Options available for this bracket
design
• Collaboration with Dow Corning® to develop ClearDuty™
optical design
• Greater resistance to gravel pitting, scratching, or cracking
• Improved sealing to prevent water from entering light
• Higher UV and thermal stability to prevent lens from
yellowing over time

2
1.800.338.7337 / www.soundo󰀨signal.com
PMPSABK002 1122 REV B
2021-2023 CHEVROLET TAHOE POLICE & CIVILIAN (LS AND Z71 MODELS)
FOR USE WITH THE 3 & 4” STUD MOUNT MPOWER®LIGHTS*
PMP2BK004 - GRILLE MOUNT BRACKET, 2 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION:
1. With the hood open, remove the upper, plastic
radiator cover on the front of the vehicle, as seen
in Figure 1.
2. Locate the passenger side bracket (002BR1067)
and place the mpower module in its intended
location and slightly thread the nuts onto the
studs. This is shown in Figure 2.
NOTE: The brackets only t directly above the
Chevrolet “bowtie” emblem on the driver and
passenger sides of the grille. The driver side
bracket must be used on the driver side and the
passenger side bracket must be used on the
passenger side.
PRO TIP: Should additional space be
desired, the grille can also be removed.
Consult a Chevrolet Service Center for best
disassembly method. Keep all hardware.
REMOVE THE RADIATOR COVER
Fig. 1
Fig. 2 Fig. 3

3
1.800.338.7337 / www.soundo󰀨signal.com
PMPSABK002 1122 REV B
2021-2023 CHEVROLET TAHOE POLICE & CIVILIAN (LS AND Z71 MODELS)
FOR USE WITH THE 3 & 4” STUD MOUNT MPOWER®LIGHTS*
PMP2BK004 - GRILLE MOUNT BRACKET, 2 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION (CONT.):
3. Notice the tab on the passenger side bracket.
This tab will be used to hold the top of the bracket
in place. With the light facing up and the tab
pointed into the grille, insert the bracket into the
correct position on the grille. Gently rotate the
bracket into the correct position. This is shown in
Figure 3. For reference, a picture of the installed
passenger side and driver side assemblies are
shown in Figure 4.
4. Attach the retaining bracket on the back side of the
grille by sliding the bracket behind the loose nuts of the
mpower module. Figure 5 shows a view of the back
side of the bracket assembly from the inside of the
fascia. Notice the location of the retaining bracket and
the nal location of the bracket tab.
5. Tighten the nuts on the mpower module studs to hold
the passenger side assembly in the correct position.
Apply a torque of no more than 15 in-lbs.
6. The nal assembly of the passenger side bracket is
shown in Figure 4.
7. Perform steps two through ve for the driver side
bracket (002BR1066).
8. Reinstall the front grille, if removed, and the upper,
plastic radiator cover, according to manufacturer’s
specications.
Fig. 4
RETAINING BRACKET
TAB MENTIONED IN STEP 3
Fig. 5