Soundoff Signal mpower PMP2BK003 User manual

1
1.800.338.7337 / www.soundo󰀨signal.com
PMP2BK003 0221
2021 CHEVROLET TAHOE POLICE & CIVILIAN (LS AND Z71 MODELS)
FOR USE WITH THE 3 & 4” STUD MOUNT MPOWER®LIGHTS*
PMP2BK003 - GRILLE MOUNT BRACKET, 6 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and re. Follow crimp connector
manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring conguration and proper integration of
system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local chassis ground (-) must be
sized to supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
CONTENTS
QTY COMPONENT
1 3 MODULE DRIVER SIDE BRACKET
1 3 MODULE PASSENGER SIDE BRACKET
2 RETAINING BRACKET
*mpower Sold Separately
OVERALL ASSEMBLY SHOWN*
INTRODUCTION:
mpower® Fascia Light Features:
• 3” and 4” Stud Mount Options available for this bracket
design
• Collaboration with Dow Corning® to develop ClearDuty™
optical design
• Greater resistance to gravel pitting, scratching, or cracking
• Improved sealing to prevent water from entering light
• Higher UV and thermal stability to prevent lens from
yellowing over time

2
1.800.338.7337 / www.soundo󰀨signal.com
PMP2BK003 0221
2021 CHEVROLET TAHOE POLICE & CIVILIAN (LS AND Z71 MODELS)
FOR USE WITH THE 3 & 4” STUD MOUNT MPOWER®LIGHTS*
PMP2BK003 - GRILLE MOUNT BRACKET, 6 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION:
1. With the hood open, remove the upper, plastic
radiator cover on the front of the vehicle, as
seen in Figure 1.
2. Locate the passenger side bracket
(002BR1064) and rmly attach the two
outermost modules. Apply a torque of no more
than 15 in-lbs.
3. Place the center module in its intended
location and slightly thread the nuts onto
the studs. At this point, the outer two lights
should be rmly attached to the bracket and
the center light should be loosely attached.
This is shown in Figure 2.
Fig. 2 Fig. 3
REMOVE THE RADIATOR COVER
Fig. 1
NOTE: The brackets only t directly
above the Chevrolet “bowtie” emblem
on the driver and passenger sides of
the grille. The driver side bracket must
be used on the driver side and the
passenger side bracket must be used on
the passenger side.
PRO TIP: Should additional space be
desired, the grille can also be removed.
Consult a Chevrolet Service Center
for best disassembly method. Keep all
hardware.

3
1.800.338.7337 / www.soundo󰀨signal.com
PMP2BK003 0221
2021 CHEVROLET TAHOE POLICE & CIVILIAN (LS AND Z71 MODELS)
FOR USE WITH THE 3 & 4” STUD MOUNT MPOWER®LIGHTS*
PMP2BK003 - GRILLE MOUNT BRACKET, 6 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION (CONT.):
4. Notice the three tabs on the passenger side
bracket. These tabs will engage behind the front
fascia and will be used to hold the top of the
bracket in place. With the lights facing up and the
tabs pointed into the grille, insert the bracket into
the correct position on the grille. This is shown
in Figure 3. Gently arc the bracket slightly and
rotate it into the correct position. For reference, a
picture of the installed passenger side assembly
is shown in Figure 4.
5. Attach the retaining bracket on the back side of the
grille light bracket by sliding the bracket behind the
loose nuts of the center module. Figure 5 shows a
view of the back side of the bracket assembly from the
inside of the fascia. Notice the location of the retaining
bracket and the nal location of the three bracket tabs.
6. Tighten the nuts on the center module to hold the entire
assembly in the correct position. Apply a torque of no
more than 15 in-lbs.
7. The nal assembly of the passenger side bracket is
shown in Figure 4.
8. Perform steps two through six for the driver side
bracket (002BR1063).
9. Reinstall the front grille, if removed, and the upper,
plastic radiator cover, according to manufacturer’s
specications.
Fig. 4
TABS MENTIONED IN STEP 4
RETAINING BRACKET
Fig. 5