Soundoff Signal mpower Fascia 4 User manual

PMP2BKUMB1 0619
1
PMP2BKUMB4 2020-2021 Ford PI Utility Under Mirror Mount Bracket Kit (each)
For Intersector Surface Mount & mpower®3” and 4” Stud or Quick Mount
1.800.338.7337 / www.soundo󰀨signal.com
PMP2BKUMB4 0221
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
PART#
YEAR, MAKE, AND
MODEL
COMPATIBILITY
PMP2BKUMB4
2020 Ford PI Utility
Surface Mount Intersector
3" or 4" mpower
®, Stud or Quick Mount
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
CONTENTS
#QTY COMPONENT
1 1 90 DEGREE BRACKET INTERSECTOR
2 2 #8 X.50 SM TRUSSHEAD PHILLIPS
31 3M DOUBLE SIDED TAPE VHB
41 THIN GASKET MATERIAL (6”)
5 1 SURFACE PREP WIPE
Intersector Surface Mount Light Features:
• Light has separate control functionality and is sync compatible
with nFORCE products
• Available in Dual or Tricolor
• Allows color to be set to ash or steady-burn
• Multiple housing colors available
mpower® Fascia Light Features:
• 3” and 4”, Stud Mount and Quick Mount Options available
• Collaboration with Dow Corning® to develop ClearDuty™ optical
design
• Greater resistance to gravel pitting, scratching, or cracking
• Improved sealing to prevent water from entering light
• Higher UV and thermal stability to prevent lens from yellowing
over time
1
2
3
4

PMP2BKUMB1 0619
2
PMP2BKUMB4 2020-2021 Ford PI Utility Under Mirror Mount Bracket Kit (each)
For Intersector Surface Mount & mpower®3” and 4” Stud or Quick Mount
1.800.338.7337 / www.soundo󰀨signal.com
PMP2BKUMB4 0221
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
K
INSTALLATION
1. Clean the top of the bracket and the underside of
the vehicle mirror with alcohol pad to ensure a clean
mounting surface.
2. Cut the VHB adhesive in half. Apply cut VHB adhesive to
the top of the mounting bracket, as seen in FIG. 1.
3. Cut the Thin Gasket matiral in half (3”) and apply to the
edge of the bracket that rests on vehicles paint.
4. Mount the bracket to the under side of the mirror in the
desired position. Make sure the bracket is not resting on
the painted surface. Apply pressure for 30 seconds to
ensure bracket is attached to mirror, as seen in FIG. 2.
5. Remove the mirror housing from vehicle according to
the manufacturer specs.
6. Using the screws holes in bracket as a guide, drill holes
for the stainless screws with a 7/64” drill bit (be careful
not to damage wiring in mirror housing.) Install provided
stainless screws through bracket into mirror housing.
Tighten until screw is snug, as seen in FIG. 3.
7. Mount light onto bracket with hardware provided with
the light and run wires into mirror. A hole may need to
be drilled to create a path for the wires, as seen in FIG.
4.
8. Re-install the mirror and tighten to manufacturer specs.
FIG. 1 FIG. 2
FIG. 3 FIG. 4
Place bracket
under mirror
NOTE: MAKE SURE THE MOUNTING HOLES ARE NOT
COVERED BY THE VHB STRIP
NOTE: WHILE MOUNTING THE BRACKET ENSURE THE
LIGHT IS PARALLEL TO THE GROUND.