Soundoff Signal mPOWER PMP2BK005 User manual

1
1.800.338.7337 / www.soundo󰀨signal.com
PMPSABK005 1122 REV B
2021-2023 DODGE DURANGO POLICE AND CIVILIAN (SXT, SXT PLUS, AND
CITADEL MODELS) FOR USE WITH THE 3 & 4” QUICK MOUNT MPOWER LIGHTS
PMP2BK005 – GRILLE MOUNT BRACKET, 2 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and re. Follow crimp connector
manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring conguration and proper integration of
system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local chassis ground (-) must be
sized to supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
CONTENTS
#QTY COMPONENT
1 2 1 MODULE OUTER MOUNT PLATE
2 2 1 MODULE INNER BRACKET
3 4 #6-32 FLANGED LOCK NUT
41 INSTALLATION INSTRUCTION SHEET
5 1 PRODUCT WARNING CARD
61 CA PROP 65 LABEL
*mpower Sold Separately
OVERALL ASSEMBLY SHOWN WITH 3” & 4” MPOWERS*
INTRODUCTION:
mPOWER® Fascia Light Features:
• 3” and 4” Quick Mount Options available for this bracket
design
• Collaboration with Dow Corning® to develop ClearDuty™
optical design
• Greater resistance to gravel pitting, scratching, or cracking
• Improved sealing to prevent water from entering light
• Higher UV and thermal stability to prevent lens from
yellowing over time
123

2
1.800.338.7337 / www.soundo󰀨signal.com
PMPSABK005 1122 REV B
2021-2023 DODGE DURANGO POLICE AND CIVILIAN (SXT, SXT PLUS, AND
CITADEL MODELS) FOR USE WITH THE 3 & 4” QUICK MOUNT MPOWER LIGHTS
PMP2BK005 – GRILLE MOUNT BRACKET, 2 MODULE
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION:
1. When removing the grille, consult with your
local Dodge service center for best disassembly
method.
2. Install the inner bracket onto the rear of the
desired mounting location. The bent anges
should face the front of the vehicle and mate with
the pattern in the grille. The slot in the bracket
should be below the wire pass-through hole.
Press the bracket rmly into the grille features
until it is securely in place, as shown in Fig. 1.
3. Install the outer mounting plate onto the outside
of the desired mounting location. The studs
should pass through the openings in the grille and
the holes in the inner bracket. The slot should be
below the wire pass-through hole when installed.
While rmly holding the mounting plate and inner
bracket in place, fasten the two brackets together
using the provided lock nuts, as shown in Fig. 2.
Tighten until snug. Do not overtighten.
4. Run the wire leads of the mpower through the
pass-through holes in the brackets and through
the grille.
5. Before securing the light to the mounting plate,
ensure the mounting plate is cleaned with the
wipe provided with the quick mount mpower
module.
6. Adhere the mpower module to the mounting
plate, as shown in Fig. 3.
7. Make nal connections and test to ensure proper
functionality.
NOTE: The brackets are designed to mount an
mpower light in any location on a compatible
Dodge Durango grille.
PRO TIP: Before installing the brackets, it is
recommended that a wire is run to each location
on the grille that a light is desired. The brackets
have slits to allow for installation after the wire
is fed through the openings on the grille.
FIG. 2
FIG. 1
Fig. 3