Specialized SpeedZone Sport Bicycle User manual

Your SpeedZone Sport bicycle
computer is equipped with the
following functions:
• SPD - Current Speed
• AV – Average Speed
• MAX – Maximum Speed
• DST - Trip Distance
• OD - Odometer (total distance)
• TM – Ride Timer
• 12/24 Hour Digital Clock
• Easy Calibration Mode
1
SPEEDZONE SPORT CYCLOCOMPUTER
Congratulations on your purchase and welcome to the growing number of
cyclists who are discovering a powerful new generation of bicycle computers.
Your Specialized SpeedZone®Sport has been designed to provide the best com-
bination of performance, features, durability, ease of use and installation.

This computer also features:
• Heavy-duty abrasion resistant
pick-up wire
• Water resistant housing
• Dual Display LCD
• 2 Year Warranty
What is included in your
SpeedZone Sport package:
1. SpeedZone Sport computer (1)
2. Mounting bracket (1)
3. Magnet with screw (1)
4. Cable tie wraps (4)
5. Mounting bracket sizing straps (3)
2
1
2
3
5
4

MOUNTING
THE SPEEDZONE SPORT
The SpeedZone Sport sensor can
mount on the right or left side of the
fork blade. Use the cable tie-wraps
provided to position the sensor. Do not
tighten until the final placement of the
sensor magnet is correct. (See figure 1)
Attach the magnet to a spoke across
from the sensor with the magnet screw.
The clearance between the magnet and
the sensor should be approximately
1/32"-1/16" (1-2mm). Tighten the
magnet and transmitter. Do not over-
tighten the magnet screw. (See figure 2)
Attach the mount to the handlebar
using the bracket screw provided.
Tighten so that the bracket cannot rotate
on the handlebar. There are several
3
FIGURE 3: MOUNTING BRACKET
FIGURE 1:
SENSOR
PLACEMENT
FIGURE 2:
MAGNET
ATTACHMENT

sizing straps provided to fit different
diameter bars. (See figure 3) Slide the
computer forward onto the mounting
until it ‘snaps’ into place with an audi-
ble click. To remove the computer, push
it backward until it releases from the
mount. To test for proper installation of
the magnet, sensor and computer, acti-
vate the computer by picking up the
front of the bicycle and spinning the
wheel. The "wheel" (1) indicator will
flash. If it does not flash check the sen-
sor and magnet alignment. Realign as
necessary until the "wheel" indicator
flashes while spinning the wheel.
PROGRAMMING
Programming the functions of your
SpeedZone Sport requires it to be
placed in various "modes" (i.e.
odometer mode, stopwatch mode).
The computer can be cycled through
these modes by pressing the "MODE"
button located on the right-hand side
of the housing. Once a specific mode
has been entered, its values can be
reset or adjusted by pressing the
"FUNCTION" button located on the
left-hand side of the housing.
1. Miles or Kilometers selection
Your SpeedZone Sport will record
speed and distance in either miles (M)
or kilometers (KM). To select miles or
kilometers, push the "MODE" button
until ODO (odometer) appears in the
lower left side of the display (This is
called the odometer mode). Hold down
the "FUNCTION" (left side) button and
‘tap’ the "MODE" button once. The
KM, M indicator will begin blinking.
You may now alternate between miles
4

and kilometers by pressing the "MODE"
button. When the correct choice is
flashing, select it by pressing the
"FUNCTION" button. You will now
enter the "Programmable Odometer"
mode. If the odometer setting is correct
push the "FUNCTION" button 4 times
to exit to odometer mode. (Otherwise,
see "Setting the programmable odome-
ter" below)
2. Setting the Programmable
Odometer
To access the programmable odometer
mode, first advance the "MODE" but-
ton until (OD) appears on the bottom
of the screen. Then hold down the
"FUNCTION" button and ‘tap’ the
"MODE" button once. (See figure 4)
The Km/h indicator will flash. If the
Km/h setting is correct press the
"FUNCTION" button once and a four-
digit number will appear. You are now
in the programmable odometer mode.
This mode is useful if you have
replaced the battery and would like to
retain the mileage you have already
ridden. To enter a mileage into the
odometer, press the "MODE" button
until the flashing digit is correct. (Note:
The "MODE" button may be held to
5
FIGURE 4: PROGRAMMABLE
ODOMETER SCREEN

scroll to the correct digit.) Press the
"FUNCTION" button to select the next
digit to the right. Repeat this process
until all four digits are entered as your
existing mileage.
3. Wheel Circumference Selection
To set the circumference for the type
of tires you are using, you can either
use the table below to obtain an
approximate tire circumference or
measure your actual tire circumference
by the rollout method.
Easy Calibration Mode:
Your SpeedZone Comp has been
preprogrammed with the following
14 Specialized tire sizes:
26 X 1.0 26 X 2.2
26 X 1.25 650 X 20
26 X 1.5 700 X 20
26 X1.9 700 X 23
26 X1.95 700 X 26
26 X 2.0 700 X 32
26 X 2.1 700 X 38
When using Easy Calibration Mode,
the SpeedZone will display the tire size
on its LCD display screen. (See figure
5) The Easy Calibration Mode is
accessed by entering the odometer
(OD) mode and holding down the
"FUNCTION" button for three seconds.
The display will now show the currently
selected tire size. To scroll through the
6

preprogrammed tire sizes tap both
the "MODE" and "FUNCTION" buttons
simultaneously. When you reach the
desired tire size press the "FUNCTION"
button once to select it and exit Easy
Calibration Mode.
Roll Out Method
The roll out method will provide the
most accurate computer calibration
and can take into account variables
such as inflation pressure, rim width
and rider weight.
1. Extend a tape measure out to
3000mm (120 inches) and lock
it in place.
2. With your tire inflated to its proper
pressure, place the valve at the
6:00 position (at the bottom) directly
over the start of the measuring tape.
3. Roll the wheel one complete
revolution until the valve stem is
again at the 6:00 position. Read the
tape directly under the valve and
note the distance in millimeters. (To
convert inches to millimeters, multi-
ply inches by 25.4). Use this num-
ber to replace the default (default
value is 2148) when programming
your computer. (See figure 6)
7
FIGURE 5: EASY CALIBRATION SCREEN

Generic Tire Size Chart
This chart is for non-Specialized
brand tires:
26 X 1.75 2140
26 X 2.0 2074
26 X 2.1 2090
650 X 20 1945
700 X 25 2124
700 X 38 2170
Programming in the circumference:
To enter the tire circumference number,
select the odometer (OD) mode and
hold down the "FUNCTION" button for
three seconds. The display will now
show the currently selected tire size.
(See figure 7) If necessary scroll
through the preprogrammed tire sizes
by tapping both the "MODE" and
"FUNCTION" buttons simultaneously
until the display shows a four-digit
number. This number represents your
tire circumference in millimeters. Press
the "MODE" button until the flashing
digit is correct. (Note: The "MODE"
button may be held to scroll to the cor-
rect digit.) Press the "FUNCTION" but-
ton to select the next digit to the right.
Repeat the process until all four digits
are entered as your tire circumference.
8
Stem
Wheel
Circumference
Roll Forward
FIGURE 6: ROLL OUT METHOD

Press the "FUNCTION" button once exit
to circumference programming mode.
4. Setting the Clock
To enter the clock mode, press and hold
the "MODE" button for three seconds.
The time will now be displayed on your
Speedzone. To set the clock press and
hold the "FUNCTION" button for three
seconds. The display will flash either
twelve (12:) or twenty-four (24:). Select
between 12: or 24: mode by pressing
the "MODE" button. Press the "FUNC-
TION" button to set the mode.
The hour digit will now begin flash-
ing. Press the "MODE" button to adjust
the hour digits and press the "FUNC-
TION" button to set. The minutes will
flash and can be adjusted by pressing
9
FIGURE 7: CIRCUMFERENCE
PROGRAMMING SCREEN
FIGURE 8: SHOW CLOCK SCREEN

the "MODE" button. (Hold the
"MODE" button to scroll through the
digits quickly) Press the "FUNCTION"
button to set the minutes and return to
clock mode (See figure 8)
COMPUTER FUNCTIONS
Speedometer
Speed is displayed when M or KM
appears on the bottom of the screen.
Speed will record up to 99.9 M/h
(99.9 Km/h) with a resolution of 0.1
M/h (0.1 Km/h)
Average Speed (AVS)
The average speed is displayed when
AV appears on the bottom of the
screen. The resolution of the average
speed is shown in 0.1M/h or Km/h
increments. (See figure 9)
Maximum Speed (MAX)
The maximum speed is displayed
when MAX appears on bottom of the
screen. The maximum speed is retained
in memory and updated when a
higher speed is attained. The maxi-
mum speed can be reset by pressing
the "FUNCTION" button for three
seconds. (See figure 10)
10
FIGURE 9: AVERAGE SPEED SCREEN