Specialized Speedzone Comp User manual

1
Printable manuals available at:
www.specialized.com
(click on: support tab)

2
Components of the Speedzone Comp 3
Installing Computer Mounts 4
Installing speed & cadence transmitter 5
Speedzone Comp user interface 6
Easy set-up and resetting 7
Using your Speedzone Comp (keyow) 15
Re-entering the pairing sequence 16
Re-entering calibration sequence 17
Clearing TRIP/ATM (Auto Timer) 18
Selecting Bike #1 - #2 setting 19
Re-setting the wheel/tire size 20
Manually setting wheel/tire size 21
Using the timer 23
Re-setting the clock and language 26
Heart rate zone setup 27
Setting power zones (auto or manual) 28
Replacing the battery 30
Specications and ranges 31
Speedzone Comp Terminology 33
Troubleshooting 34
Warranty information 35
Table of contents

3
Components of the Speedzone Comp
1. Speedzone cyclo-
computer head unit
2. Cadence magnet
3. Handlebar bracket
4. Base mount
5. Steerer tube bracket
6. Speed transmitter
7. Cadence sensor
8. Spoke magnet
9. Zip ties

4
• Install the steerer tube bracket base assembly on the steerer
tube. Re-install the steerer tube top cap.
• Place handlebar bracket on handlebar, attach the base mount
to the handlebar bracket with the included bolt.
• Adjust base to desired angle with bolt adjustment.
Installing Computer Mounts
steerer tube bracket handlebar bracket

5
• Adjust spoke magnet so path of rotation passes along the
groove area inside the sensor. IMPORTANT: Placing magnet
outside the groove path may cause improper reading.
• Attach the cadence magnet with self adhesive pad to the
crank arm, and position the sensor’s raised line within the
magnet’s rotation path.
Installing speed & cadence transmitter
!
1-5mm
1/16 - 1/4 in.
!

6
Speedzone Comp user interface
Digital Speed Display
Secondary function display
Secondary function indicator
Average speed comparator
Battery low indicator
Bike #2 indicator
Speed (10ths)
Miles (English)/KM (metric)
Set key Mode key
Start/Stop key
Power(watts)/Heartrate(BPM)
*Cadence signal
Bike #1 indicator
*Power indicator
*Heartrate signal
*Heartrate indicator
(when power is not paired)
* Illuminated when signal is paired

Setup 7
Easy set-up and resetting
2 sec PRESSOR
Hold “start/stop”
for 2 seconds to
initiate easy setup;
this is only required
to wake unit from
shipping mode
(rst purchased).
Wake from shipping mode Reset and all clear
Press reset button
to enter easy
set up.
Blank screen
indicates
shipping mode

8Setup
From initial start-up:
Language selection & clock setting
select language select 12/24 hr select hour

Setup 9
...continued clock and date setting
select minute select year select month

10 Setup
Wheel and tire size selection
select day scroll through
wheel sizes
bicycle #1 bicycle #2
scroll through
wheel sizes for
bike #2
scroll through
wheel sizes
scroll through
wheel sizes for
bike #1
(To manually set wheel size see page 20)

Setup 11
Metric (km) or English (mi) & odometer
select km / miles select digit select digit
x4
km or miles

12 Setup
• Max heart rate guideline: 220 minus your age
• Normal power (N-PWR) = power (watts) sustained for 20-40
minutes of riding
Heart rate / normal power / power zone
enter max HR enter normal
power
auto
To set manually see page 28

Setup 13
Head unit is searching for Speed, Cadence, Heart, and Power
transmission signal from ANT+ digital transmitters.
Pairing digital ANT+™ wireless device
begin signal pairing
sequence...
head unit is
searching for
digital signals
Speed / Cadence /
Heartrate / Power
PAIRED
Clock

14 Setup
begin calibrating...
head unit is
searching for
digital signal
Power device is
calibrated
Calibration
number displayed
Clock
2 sec.
When “CALIB” is ashing follow instruction for calibrating your
specic power meter. Calibration mode will only activate when
paired with power device (see page 13).
Calibrating power devices
*Press “set” to bypass calibration and proceed to normal operation.
*

15
Press to access major functions
Press to access sub functions
Using your Speedzone Comp (keyow)

16
Re-entering the pairing sequence
Scroll to AVGSPD mode, and hold “set” key for 2 seconds.
Every wireless device must be ANT+ compatible device to
transmit data.
2 sec.
Head unit is
searching for
signals (see
earlier section)
S - Speed
C - Cadence
H - Heart Rate
P - Power

17
Scroll to AVGPWR mode, and hold “set” key for 2 seconds
Re-entering calibration sequence
2 sec. begin calibrating...
(see page 14)

18
In “TRIP“ or “ATM“ mode, press “mode“ key for two seconds.
Resetting “TRIP“ will only clear ride shown data only and PC
download data is saved.
Clearing TRIP/ATM (Auto Timer)
2 sec.

19
When in “TRIP“ mode, press “set“ key for two seconds.
Devices (ANT+ transmitters) must be “paired” for second (bike
#2) setting.
Selecting Bike #1 - #2 setting
2 sec.
*bicycle #1
proceeds to AVGSPD function
*bicycle #2

20
*bicycle #1 *bicycle #2
activates wheel/
tire size options
2 sec
• In “ODO” mode, press “mode” key for two seconds
• Select desired wheel/tire size (see earlier section for details)
Re-setting the wheel/tire size
scroll through
sizes or manually
set size in mm
(see page 10)
scroll through
sizes or manually
set size in mm
(see page 10)