Spectrum Industries 22860 User manual

Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
1. Place the worksurface face-down onto a non-abrasive surface.
2. Align the legs with the mounting holes, and install (2) #14 x 1-3/4”
PHSM screws into each leg but do not tighten completely yet.
Figure 1.
0191978R2 Page 1 of 4
Assembly InstructionsAssembly Instructions
(4) 026064
1/4-20 x 5/8” PHMS
Figure 1
(1) 025069
Glide wrench
The side of the leg with
the threaded hole should
be on the ip-top side
(1) 036281
Dual unit-to-unit
bracket
Flip-top
Worksurface
#14 x 1-3/4” PHSM
(2 per leg)
(1) 0167153
Unit-to-unit bracket
(2) 026011
1/4-20 x 2” FHMS
(1) 052547 - Right Leg
(1) 052544 - Left Leg
(1) 0152133
44”W x 30”D
Worksurface w/ support
(1) 052469
Chair rail
(1) 052468
44” Cord channel /
Modesty panel
Esports Evolution Desk (44”W)
22860
(4) 037779
5/16-18 x 1”
Glide
(4) 0101381
#14 x 1-3/4” PHSM
(4) 0101382
#14 x 7/8” PHSM
Right
leg
Left
leg
Attach legs to worksurface
1
X2
Assembly tip: Do not tighten component
fasteners completely until all have been
installed. Keeping them loose will help with
alignment between parts during assembly.

Leg adjustment
0191978R2 Page 2 of 4
1. Orient the modesty panel/cord channel as shown and attach to the
legs with (4) 1/4-20 x 5/8” PHM screws. Figure 2.1.
2. Install the (4) glides to the bottom of the legs. The glides can be
adjusted later to keep the desk level on uneven surfaces.
3. Tighten ALL screws.
Figure 2.1
Modesty panel /
cord channel
1/4-20 x 5/8” PHMS
(4 required)
Glides
(4 required)
The worksurface height can be adjusted from 24”H - 32”H in 1” increments.
Figure 2.2. Adjustment is easier when the desk is upside-down.
1. To adjust the legs, remove the (4) pre-installed adjustment screws.
(Fully-support the lower section of the leg while removing). Figure 2.3.
2. Choose a height and align the corresponding set of leg holes.
3. Install the (4) previously removed screws in the new holes and tighten securely.
4. Repeat this procedure on the second leg. Make sure to use the same set of
holes as used on the rst leg.
Figure 2.2 Figure 2.3
Lower section
Up to 8” of
adjustment
Up to 8” of
adjustment
Adjustment
screws
8”
24”
32”
Install cord channel / modesty panel and glides
2

3. Attach the unit-to-unit bracket to the rear of the legs (behind cord
channel) using the existing cord channel screws.
(Loosen screws to install, then re-tighten).
4. Tighten all screws.
Unit-to-unit
bracket
(2) 1/4-20 x 5/8”
PHMS
0191978R2 Page 3 of 4
1. Carefully ip the desk upright-this will require at least two people.
2. Attach the chair rail with (2) 1/4-20 x 2” FHM screws as shown.
Note the chair rail should extend above the worksurface, and the
countersunk holes should be on the outside. Figure 3.1, 3.2.
3. Tighten all screws securely.
Figure 3.2
Two desks can be connected together with the (2) included unit-to-unit brackets.
1. Locate the desks next to each other in their nal position.
2. Attach the dual unit-to-unit bracket to both worksurfaces using (4) #14 x
7/8” PHSM screws. Do not tighten scres yet.
1/4-20 x 2” FHMS
(2 required)
Chair rail
Figure 4.1
Desk #1
Dual unit-to-unit
bracket
Figure 3.1
1/4-20 x 2”
FHMS
Chair rail
Extends above worksurface
Desk #2
(4) #14 x 7/8”
PHSM screws
Attach chair rail
3
Attaching desks together (optional)
4
Figure 4.2
Desk #1 Desk #2
Student-side Audience-side

0191978R2 Page 4 of 4
1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Warranty
1-800-235-1262
Toll-free HELPLINE
[email protected]
© 2021 Spectrum Industries Inc., All rights reserved.
We will make it right for you!
Thanks for choosing Spectrum! Spectrum is committed to provide complete customer satisfaction.
Each of our products is manufactured from the best materials available and each product is strin-
gently monitored throughout the production process through our P.A.C.E. program (Product Assur-
ance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from
defect for the period set out in the warranty from the date of delivery.
For a listing of all product specifi c warranty terms please visit our website at:
https://www.spectrumfurniture.com/en/resources/purchasing-terms-warranty