Spectrum Industries Inspiration Plus Side Table User manual

Assembly Instructions
Tools Required
0119685 Page 1 of 4
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Inspiration Plus Side Table
55413
Phillips
Screwdriver
(3) 052901
8-32 x 3/8”
PHMS
(17) 026064
1/4-20 x 5/8”
PHMS
(4) 026073
#8 x 3/4” PHSM
screw
(2) 0105662
5/16-18 Stem
Caster
Parts bag with casters
(for lecterns with casters)
(3) 052901
8-32 x 3/8”
PHMS
(17) 026064
1/4-20 x 5/8”
PHMS
(2) 037779
5/16-18 x 1
Glide
Parts bag with glides
(for lecterns with toe kick)
(1) 0119257 Worksurface or
(1) 0119688 Worksurface (with cutout)
(1) 0111446
Modesty Panel
(1) 0111447
Leg
(1) 0111450
Backer Plate
(1) 0111472
Leg
(1) 0111449
Unit-to-Unit Bracket
(1) 025069
Caster / Glide
wrench
(4) 026073
#8 x 3/4” PHSM
screw
(1) 025069
Caster / Glide
wrench
Caster / Glide
wrench
(included)

Backer
Plate
Lectern Side
Panel
Figure 1
1. The table is symmetrical and can be mounted on the left or right side of the lectern.
Determine which side the table will be mounted.
2. Attach the unit-to-unit bracket and the backer plate to the left or right side panel with (3)
1/4-20 x 5/8” PHM screws. Figure 1. The backer plate will be inside the lectern. Do not
tighten the screws completely-they will be tightened after the table is connected.
1/4-20 x 5/8”
PHM screws
(3 required)
Unit-to-Unit
Bracket
1. Attach unit-to-unit bracket to lectern
0119685 Page 2 of 4

2. Assemble Table
0119685 Page 3 of 4
1. Place the worksurface face down onto a non-abrasive surface.
2. Attach the leg as shown with (8) 1/4-20 x 5/8” PHM screws. Figure 2A. Tighten securely.
3. Attach the (2) casters or (2) glides to the bottom of the leg and tighten securely.
4. Attach the modesty panel to the worksurface with (4) #8 x 3/4” PHSM screws. Figure 2A shows a right-hand table installation.
Note: Figure 2A shows a right-side table assembly.
If assembling a left-side table, the modesty panel can
be ipped and attached to the opposite side of the
worksurface using the other set of predrilled holes.
Figure 2A
Figure 2B
Modesty
Panel
Worksurface
5. Attach the modesty panel to the leg with
(3) 1/4-20 x 5/8” PHM screws. Figure 2B.
Leg
1/4-20 x 5/8”
PHM screws
(8 required)
(2) Casters or
(2) Glides
When assembling a left side
table, use this set of 4 holes to
attach the modesty panel
Modesty
Panel
1/4-20 x 5/8”
PHM screws
(3 required)
#8 x 3/4”
PHSM screws
(4 required)
Modesty Panel
ush with work-
surface edge
Note: The fastener slots in the mod-
esty panel allow slight adjustment
with the worksurface. The modesty
panel should be attached ush with
the edge of the worksurface.

3. Attach table to lectern
0119685 Page 4 of 4
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2015 Spectrum Industries Inc., All rights reserved.
1. If your Inspiration lectern is the mobile version, lock all four casters.
2. Set the edge of the assembled table onto the previously installed unit-to-unit bracket. Figure 3A.
3. Align the bracket and worksurface mounting holes and attach with (3) 1/4-20 x 5/8” PHM screws (nger-tight only).
4. Align the modesty panel and lectern side panel mounting holes and attach with (3) 8-32 x 3/8” PHM screws.
5. Make sure the table is level side-to-side, and front-to-back, then tighten all screws securely-including the unit-to-unit bracket screws.
Figure 3A
Figure 3B
Modesty
Panel
Worksurface
1/4-20 x 5/8”
PHM screws
(3 required)
#8-32 x 3/8”
PHM screws
(3 required)
Lectern
Side Panel
Unit-to-unit
Bracket
with slots
Note: The side table with casters is only designed for
short distance mobility and repositioning within a room.
Frequently moving the unit long distances or over uneven
thresholds is not recommended. Do not lift up or pull the
table-move the table and lectern together.
Assembled
Table
Note: The table worksurface should
be parallel with the lectern work-
surface. The Unit-to-unit bracket
has slots that allow slight vertical
adjustment with the fasteners that
attach it to the side of the lectern. If
adjustment is necessary, loosen the
fasteners attaching the table to the
lectern, reposition the unit-to-unit
bracket and table, then retighten.