SSV Works CM2-UD10 User manual

CM2-UD10
Commander and Maverick
Under Dash Subwoofer Enclosure
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in
material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty
against defects in material or workmanship. All SSV Works Speakers are covered by a
limited 1 year warranty against defects in material or workmanship. Labor for replacement of
defective components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
FOLD THIS TAB UP ON DOTTED LINE
ENILDETTODNOPUBATSIHTDLOF
FOLD THIS TAB UP ON DOTTED LINE
CM2-UDSB10 DRILL TEMPLATE
SSV WORKS INC. CM2-UDSB10 DRILL TEMPLATE REV. A, 5/5/2017
1. CM2-UD10-U
Enclosure x 1
3. M6 Washers x 5
6. Bottom Mounting
Bracket x 1
7. Drill Template
4. M6 x 16mm Screw x 4
5. M6 Locking Hex Nut x 1
- Utility Knife
- 10mm Socket with Extension
- Drill with 1/8” and ¼” Drill bit
- Wrench for Battery Terminal
- #3 Phillips Screwdriver
- T-30 Torx Driver

B. Attach the bottom mounting bracket to the enclosure using the
(2) M6 screws and washers.
C. Extract the 2 10mm bolts and 2 rivets to remove the panel
behind the passenger side front wheel.
D. Follow the directions to cut out the drill template and place in
the cavity behind the panel that was just removed. Drill the 2
holes indicated on the template. When folded correctly, the
template should sit in place as shown.
CM2-UD10
B
C D
A. Remove the at trim piece above the glove box by pulling straight out toward the
grab bar and remove the (2) 10mm bolts that secure the top of the glove box. If
the vehicle is equipped with the factory winch, the connection will need to be
unplugged once the glove box is removed.
AA

E. Place the enclosure on the passenger side oorboard, tilt the
top of the enclosure toward the center of the vehicle and angle
the bottom in toward the center using a sideways motion. The
enclosure is placed correctly when it sits ush against the
sidewall and the oor, do not try to align the enclosure to the
rewall, this will cause the enclosure to lift off the oor.
F. Screw (2) M6 screws with washers through the drilled holes into
the enclosure. Replace the factory inner fender panel.
EF
CM2-UD10
G. Once the glove box and enclosure are in place and glove box
function has been checked make sure the enclosure is ush
to the oor and sidewall, mark the mounting holes inside the
enclosure and on the oor bracket.
G
I. Connect the speaker harness to the subwoofer, be sure to
connect the “+” speaker wire to the “+” subwoofer terminal
and the “-“ speaker wire to the “-“ subwoofer terminal. Mount
the subwoofer in the enclosure.
I
J. Using the utility knife, cut the 2 small plastic bungs off of the back
of the glove box, this will allow more clearance for the glove box to
align properly.
J
K. Route the speaker wire away from any moving parts and any
sharp metal and connect to the amplier. After the system has
been tested, re-assemble any vehicle parts that were removed.
K

CM2-UD10
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using with
an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.
“+”
“+”
“ - ”
“ - ”
Amplier
© 2019 SSV Works, Oxnard, CA 93030 CM2-UD10 Rev. E 7-25-19

FOLD THIS TAB UP ON DOTTED LINE
ENILDETTODNOPUBATSIHTDLOF
FOLD THIS TAB UP ON DOTTED LINE
CM2-UD10 DRILL TEMPLATE
SSV WORKS INC. CM2-UD10 DRILL TEMPLATE REV. B, 9-27-17