SSV Works PHASE 5 X3-5K User manual

POWERSPORTS AUDIO KIT
PHASE 5
CAN-AM
®
MAVERICK X3
®
Disassembly, Wire and
Amplier Plate Installation
Dash Kit Installation
Underseat Subwoofer
Installation
Dash Speaker Pods
Installation
Cage Mount Speaker Pods
Installation
pg 3
pg 11
pg 15
pg 19
pg 23

2

3
X3-5K
Can-Am Maverick X3 & X3 Max
Kicker 5 Speaker Audio Kit
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in
material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty
against defects in material or workmanship. All SSV Works Speakers are covered by a
limited 1 year warranty against defects in material or workmanship. Labor for replacement of
defective components is not covered. Contact SSV Works for further warranty information.
1. Amp Power Wire
2. Front B-H1149 Speaker Harness
3. Rear B-H1151 Speaker Expansion
Harness
4. MRB3 Power & Ground Connector
5. Direct-t Amp Plate with pre-tuned
Amp(s) and MRB3 Brain
TOOLS NEEDED FOR INSTALLATION WIRE AND CABLE PARTS LIST
6. M6 x 1.0 Screw x 1
7. M6 Washer x 1
8. M6 Nut x 1
9. Zip Ties x
10. WP-H16PG84-6 Harness
- T30 torx
- 10mm wrench or socket
- 13mm wrench or socket
- 18 mm socket with extention
- Wire crimpers
- Panel removal tool
- #2 screw driver
- 1” Uni bit ( for USB/Aux )
- #3 screw driver
PARTS LIST IMAGES
2. Front B-H1149 Speaker
Harness
6. M6 x 1.0 Screw x 1 7. M6 Washer x 1 7. M6 Washer x 1
8. Zip Ties x 5 10. WP-H16PG84-6 Harness
1. Amp Power Wire with Fuse
Holder
5. Direct-t Amp Plate with pre-
tuned Amp(s) and MRB3 Brain
3. Rear B-H1151 Speaker
Expansion Harness
4. MRB3 Power & Ground
Connector

4
A
PANELS AND DASH DISASSEMBLY
B B B
A
C
A. To remove the seat, use a 13mm socket and wrench to remove front (2) bolt and nut, and use a 18mm socket to remove (2) rear nuts and seat belt nut
( repeat on other seat)
B. Carefully unsnap center dash side panels by hand or with a panel removal tool.
C. Unscrew (2) T30 torx located on the center console panel under the
dash. Use a panel tool to remove push pins on passenger side.
D
D. Carefully unsnap rear cover to expose the engine compartment

5
PANELS AND DASH DISASSEMBLY
EE E
E2. Using panel removal tool unsnap (2) push clips on the driver and passenger side dash covers. Unscrew the (4) T30 screws on the passenger
side, and (7) T30 screws on the driver side.
E. Remove gas cover on the passenger side to expose a 10mm nut. Unscrew with a wrench and T30 torx driver.
E2 E2
F
F. Remove fender well panel using a T30 driver (will need a10mm socket for
the screw near the headlight)
G
G. After the fender well panel is removed, remove the third fastener clip
from the bottom.

6
RUNNING AMP POWER CABLE AND SPEAKER WIRE
I1 I2
I. In this step you will be feeding all of the necessary wires from the top drivers side dash down the center dash column. Be sure to run all of
the wires along side the factory cabling to avoid any moving parts. Feed both amp power wires, rear speaker expansion harness, subwoofer
harness, and power/ground for MRB3 from top driver side down the center column (I1). Pull all wires through the bottom center column and
across the center console with the factory wiring (I2).
J. Run rear expansion harness through rear center console cavity, following the
factory cables. If you are installing a 3-speaker kit, simply zip tie the cable
to a factory harness as this step is completed. If installing a 5-speaker kit,
please refer to the installation of the Cage Mounted Speakers.
H. Connect the MRB3 Power into the WP-H16PG84-6. Using the butt splice
terminals on the WP-H16PG84-6, connect black to black and red to yellow.
J
H
The connection of each cable will be address further along in the instructions.
WP-H16PG84-6
MRB3 Power Connector

7
INSTALLATION NOTES
AMP TRAY MODIFICATION WITH USE
WITH AN AFTERMARKET ROLL CAGE
1. REMOVE THIS THREADED
STUD BEFORE INSTALLAION OF
THE AMP TRAY. GENTLY TAP OUT
THE THREADED STUD WITH A
HAMMER. BE CAREFUL NOT TO
BEND THE BRACKET.
2. IF NEEDED, INCREASE THE
DIAMETER OF THE HOLE TO
ACCOMMODATE THE ROLL
CAGE BOLT

8
AMP PLATE INSTALLATION
L
NO
K
M
K. From underneath driver side place amp plate between the two cross bars behind the steering wheel.
L. Make sure the threaded bolt on the amp plate goes through the
factory hole located in the corner where the cage tubing connects.
* If your vehicle is equipped with an aftermarket cage, refer to page 2
for the installion of the amp tray.
N. Make a pilot hole with a pick tool through the top right screw hole in
the amp plate and push all the way through the vehicle panel.
O. Drill a larger hole through the pilot hole using a 1/4” drill bit. Be sure
to move the amp plate out of the way before drilling.
M. Secure the amp tray to the vehicle using the supplied M6 nut and
washer.
K

9
AMP PLATE INSTALLATION
P1 P2
Q. Connect the B-H1149 to the front output of the 300.4 amplifer. Connect the B-H1151 to the rear output of the 300.4 amplier. Connect the B-H1152 to
the output of the 500.1 amplier (Q1). Connect the B-H1221 MRB3 power harness to the MRB3 brain (Q2). Connect both amplier power harnesses to
each amplier (Q3).
P. Route the front B-H1149 speaker harness towards the driver and passenger side of the vehicle and leave the 4 pin connector at the driver
side of dash (P1). Route the passenger side speaker wire under the center dash panel all the way to the passenger side speaker location (P2).
Q3Q2Q1
R R R
R. Connect the power and ground for the MRB3 brain on the power strip located on the passenger side of the center console. Unscrew the top post, remove
the nut and install the black-ground wire terminal. Replace the nut. Unscrew the center post, remove the nut and install the red-battery power wire
terminal. Replace the nut.

10
USB/AUX INPUT PORT INSTALLATION
S
S. Remove the (4) T30 torx on the front and inside of the glove box T. Remove push clips from underneath glove box.
T
U
U. Pull up and remove the glove box.
V
V. Drill a 1” hole through the left side of the glove box for wiring
W W
W. Unscrew and remove the plastic nut from the port. Make sure to open the fuse
holder and remove the fuse so the nut will t through it. Feed in the wires through
the hole. Keep the fuse holder open and empty until it has passed through the hole.
X
X. Feed the plastic nut back through the wires and cables and screw
back on to the port. Hand tighten only.
outside viewinside view inside view