SSV Works X32-PUS10 User manual

X32-PUS10
2016+ Can-Am Maverick x3
10” Passenger Side Under Seat Enclosure
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in material
or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against
defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year
warranty against defects in material or workmanship. All Kicker Ampliers are covered by a
limited 2 year warranty against defects in material or workmanship. Labor for replacement of
defective components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
2. M6x1.0x16mm T30 Torx
Screws & Washers x10
7. B-Bracket x1
11. M6 10mm lock nut x1
8. Large Bracket
12. Foam Strips x5
3. Thread Rolling Screw x2
(#3 Phillips Screwdriver)
4. M6x1.0x25mm T30
Torx Screw x1
5. Large Washers x1
9. Seat Spacer x1
1. X32-PUS10 Enclosure
6. D-Bracket x1
10. Brake Line Spacer x1
- 10mm, 13mm, 16mm and
18mm Sockets & Wrenches
- T-30 Torx
Driver
- 1½” Hole Saw - Hole Punch /
Scribe Tool
- Ratchet & Extension - #3 Phillips
Screwdriver
Triangular
end

A. Apply the short foam strips to the large bracket in the order shown above (A1).
Apply the long foam strips to the outside edges of the enclosure. (Driver outside = left /
Passenger outside = right) (A2).
B. Fasten the D-Bracket to the bottom right side of the enclosure
with the (2) M6x1.0x16mm T30 torx screws and washers.
C. Secure the large bracket to the right side of the enclosure with (4)
M6x1.0x16mm T30 torx screws and washers.
X32-PUS10
A2A1
B C
SSV HOLE PATTERN
KICKER HOLE PATTERN
FOR UNLOADED ENCLOSURES:
Pink hole pattern: SSV Works Subwoofer
Blue hole pattern: Kicker Subwoofer
If using an alternative brand subwoofer
that does not match the existing pre-
drilled hole patterns, drill new holes
away from the pre-drilled holes. Use the
(8) provided #7 screws when installing
your own subwoofer. #7 Screws x 8

E. Remove the factory 10mm Brake line nut and bolt. Place the M6x1.0x25mm screw and washer through the brake line mounting tab. Slide onto the
screw in the following order, brake line spacer, brake line, washer and secure together with the M6 10mm lock nut. (Disregard this step for the 4-seat
Maverick X3 Max)
E E E
X32-PUS10
D D
D. For passenger seat removal slide the seat to the furthest back position. Remove the (2) front 13mm bolts. Flip up the seat cushion to access
the rear mounting points and remove the (2) 18mm lock nuts. Tilt the seat forward and remove the (1) 16mm seat belt bolt. Disconnect the seat
belt sensor if applicable.
G. Replace the factory seat bolt spacer with the supplied SSV
Works spacer on top of Bracket D.
F. Remove the seat mounting spacer from the seat mounting stud
towards the center of the car.
Feed the enclosure down under the seat bar and simultaneously
guide “Bracket D” over the inner seat mounting stud that does
not have the spacer. The Factory spacer will not be re-used***
As the enclosure is set into place, the brake line is to run along
the dedicated channel on the sub enclosure. Make any routing
adjustments to the brake line so the enclosure lays down at without
any tension on the brake line. Bracket D should be sitting at on top
of the oor plastic once the enclosure is in place.
FG

H. Place Bracket B on the left side of the enclosure (H1). Secure Bracket B to the enclosure with (2) M6x1.0x16mm T30 Torx screws and washers (H2).
Line up the top of Bracket B with the hole on the seat mounting bracket and secure to Bracket B with a M6x1.0x16mm T30 torx screw and large washer.
H1 H2 H3
J. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplier.
Connecting the X32-PUS10 using the pre-installed four-pin connector will require an optional SSV Works plug-&-play harness
B-H1152 (sold separately).
J J
X32-PUS10
I. The large bracket will align over (2) factory holes in the chassis.
Using a #3 Phillips screwdriver, secure the large bracket to the
chassis with the provided (2) thread rolling screws.
I

X32-PUS10 © 2019 SSV Works, Oxnard, CA 93030 X32-PUS10 Rev. A 12-3-19
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using
with an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.
Amplier
“+”
“+”
“ - ”
“ - ”
Connecting the X32-PUS10 using the pre-installed, four-pin connector will require an optional SSV Works plug-&-play harness (B-H1152 - sold
separately). If you are not using the B-H1152 harness, simply cut off the four-pin connector and follow the wiring instruction below.
USING A SSV WORKS HARNESS
THIS STEP IS OPTIONAL
H. To help minimize skid plate rattle, we have supplied a drill template that adds 4 holes to help relieve air pressure that is being generated by the high
output of the sub enclosure. Remove sub enclosure and leave brackets in place, and line up the template under the sub mounting brackets (H1). With
hole punch/scribe tool mark the 4 drilling points through the template on to the oorboard (H2). Drill the four (4) - 1½” holes with a hole saw (H3).
Some x3 models have a thinner skid plate that
others and may rattle more. We have provided a
drill template to help minimize skid plate rattle.
H1 H2 H3
DRILL TEMPLATE