ST X-NUCLEO-OUT14A1 User manual

Introduction
The X-NUCLEO-OUT14A1 is an industrial digital output expansion board for STM32 Nucleo. It provides a powerful and flexible
environment for the evaluation of the driving and diagnostic capabilities of the ISO808A-1 octal high-side smart power solid state
relay, with embedded galvanic isolation and 20MHz SPI control interface, in a digital output module connected to 1.0 A industrial
loads.
The X-NUCLEO-OUT14A1 directly interfaces with the microcontroller on the STM32 Nucleo driven by GPIO pins and Arduino®
R3 connectors.
The galvanic isolation between the microcontroller and the process stage is guaranteed by the ISO808A-1.
The expansion board can be connected to either a NUCLEO-F401RE or a NUCLEO-G431RB development board.
It is also possible to evaluate a 16 channel digital output system enabling the daisy chaining feature on two X-NUCLEO-
OUT14A1 stacked expansion boards.
Figure 1. X-NUCLEO-OUT14A1 expansion board
Getting started with the X-NUCLEO-OUT14A1 industrial digital output expansion
board for STM32 Nucleo
UM3082
User manual
UM3082 - Rev 1 - December 2022
For further information contact your local STMicroelectronics sales office. www.st.com

1Getting started
1.1 Overview
The X-NUCLEO-OUT14A1 embeds the ISO808A-1 intelligent power switch (IPS), which features galvanic
isolation, 20 MHz SPI and Power Good diagnostic, overcurrent and overtemperature protection for safe output
loads control.
The board is designed to meet the application requirements for the galvanic isolation between the user and power
interfaces.
The galvanic isolation embedded by the ISO808A-1 satisfies this requirement, avoiding the necessity of external
optocouplers, with a consequent cost saving and a reduced application size.
The expansion board features:
• Based on the ISO808A-1 octal high-side switch, which features:
– Operating range 9.2 to 36 V
– Low power dissipation (RON(MAX) = 260 mΩ)
– Process side operating current: up to 1.0 A per channel
– Embedded 2k VRMS galvanic isolation
– PGOOD (VCC voltage level alarm signalization)
– 20 MHz SPI with daisy chaining
– Fast decay for inductive loads
– Undervoltage lock-out
– Overload and overtemperature protections
– Loss of ground protection
– PowerSO36 package
• Application board process side operating range: 10 (J10 open) to 33 V (J9 closed)
• Extended operating range of process side from 9.2 (J10 closed) up to 36 V (J9 open)
• Application board logic side operating voltage 3.3 to 5 V
• Green LEDs for outputs on/off status (J6 and J7 close 1-2, 3-4, 5-6, 7-8)
• Red LED for common overheating and communication error diagnostic (J3 close 1-2)
• Red LED for PGOOD signalization (J3 close 3-4)
• Yellow LED for output enable status signalization (J3 close 5-6)
• Process and logic supply rails reverse polarity protections
• Compatible with STM32 Nucleo development boards
• Equipped with Arduino® UNO R3 connectors
• RoHS and China RoHS compliant
• CE certified
• Radiated emission: class B according to the standard EN 55032
UM3082
Getting started
UM3082 - Rev 1 page 2/19

1.2 Digital section
The digital section is associated with the STM32 interface and the digital supply voltage to and from the
X-NUCLEO-OUT14A1 expansion board.
Figure 2. X-NUCLEO-OUT14A1 expansion board: digital interface section
The dotted green line indicates the whole digital interface section. The pink rectangles identify the Arduino® UNO
R3 connectors.
The four Arduino® UNO R3 connectors:
• allow the expansion board to communicate with the STM32 Nucleo development board microcontroller
accessing the STM32 peripheral and GPIO resources;
• provide the digital supply voltage between the STM32 Nucleo development board and the X-NUCLEO-
OUT14A1 expansion board, in either direction.
Usually, the STM32 Nucleo development board supplies the expansion board by a 3.3 V or 5.0 V generated by
the USB.
Alternatively, it is possible to supply the STM32 Nucleo development board by the expansion board. In this case,
an external supply voltage (7-12 V) should be connected to the CN11 connector (not mounted by default) on the
expansion board and the ground loop should be closed by mounting D2 (enabling the reverse polarity protection)
or by closing J5 (without reverse polarity). In this scenario, the logic side of the ISO808A-1 can be supplied by the
3.3 V supply rail generated by the expansion board: in this case, on the X-NUCLEO-OUT14A1, J4 must be closed
between pins 5 and 6.
To supply the VIN voltage rail, it is necessary to:
• close the JP5 jumper between pins 2 and 3 and open the JP1 jumper on the NUCLEO-F401RE;
• open the JP5 jumper between pins 1 and 2 and close the JP5 jumper between pins 3 and 4 on the
NUCLEO-G431RB.
The pin 3 of the connector CN11 can be used to supply the logic side of the ISO808A-1 independently by the
expansion board. In this case, on the X-NUCLEO-OUT14A1, the pins 1 and 2 of J4 must be closed (pins 5-6
open).
UM3082
Digital section
UM3082 - Rev 1 page 3/19

1.3 Power section
The power section involves the power supply voltage (CN1, pin 1 for VCC, pin 2 for GND), the load connection
(eight loads can be connected between each pin of CN2, CN3, CN4, and CN12 and pin 2 of CN1), EMC
protections (U2), and supply reverse polarity protection (D1).
Figure 3. X-NUCLEO-OUT14A1 expansion board: power section components
1. ISO808A-1
2. Output and power supply connector
3. Output channels - green LEDs
4. Status (overtemperature) red LED
5. Output Enable yellow LED
6. Power Good - red LED
For EMC:
•the SM15T39CA transient voltage suppressor (U2), enabled by closing J9, is placed between VCC and
GND tracks to protect the ISO808A-1 against surge discharge on the supply rail path up to ±1 kV/2 Ω
coupling;
• in the common mode surge testing, two single-layer capacitors (C11 and C12 - not included) must be
soldered at the predisposed locations;
• the ISO808A-1 output stages do not require additional EMC protections with respect to the IEC61000-4-2,
IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-8 standards.
The EMC performance of the X-NUCLEO-OUT14A1 is detailed below:
• for emission (when the DC input port of the board is powered by an AC-DC, DC-DC or battery with a cable
that does not exceed a three-meter length), compliance with standards:
– EN IEC 61000-6-3:2021
– EN 55032:2015 +A1:2020
• for immunity, compliance with standards:
– EN IEC 61000-6-1:2019
– EN 55035:2017 +A11:2020
UM3082
Power section
UM3082 - Rev 1 page 4/19

1.4 Hardware requirements
The X-NUCLEO-OUT14A1 expansion board is designed to be used with the NUCLEO-F401RE or NUCLEO-
G431RB STM32 Nucleo development boards.
To function correctly, the X-NUCLEO-OUT14A1 must be plugged onto the matching Arduino® UNO R3 connector
pins on the STM32 Nucleo board as shown below.
Figure 4. X-NUCLEO-OUT14A1 and STM32 Nucleo stack
1.5 System requirements
To use the STM32 Nucleo development boards with the X-NUCLEO-OUT14A1 expansion board, you need:
•a Windows PC/laptop (Windows 7 or above)
• a type A to mini-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
F401RE development board
• a type A to micro-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
G431RB development board
• the X-CUBE-IPS firmware and software package installed on your PC/laptop
UM3082
Hardware requirements
UM3082 - Rev 1 page 5/19

1.6 Board setup
Step 1. Connect the mini-USB or micro-USB cable to your PC to use the X-NUCLEO-OUT14A1 with NUCLEO-
F401RE or NUCLEO-G431RB development board
Step 2. Download the firmware (.bin) onto the STM32 Nucleo development board microcontroller through
STM32 ST-LINK utility, STM32CubeProgrammer, and according to your IDE environment as detailed in
the table below.
Table 1. NUCLEO-F401RE development board supported IDEs - bin files
NUCLEO-F401RE
IAR Keil STM32CubeIDE
EWARM-OUT12_14-
STM32F4xx_Nucleo.bin
MDK-ARM-OUT12_14-
STM32F4xx_Nucleo.bin
STM32CubeIDE-OUT12_14-
STM32F4xx_Nucleo.bin
Table 2. NUCLEO-G431RB development board supported IDEs - bin files
NUCLEO-G431RB
IAR Keil STM32CubeIDE
EWARM-OUT12_14-
STM32G4xx_Nucleo.bin
MDK-ARM-OUT12_14-
STM32G4xx_Nucleo.bin
STM32CubeIDE-OUT12_14-
STM32G4xx_Nucleo.bin
Note: By default, the X-NUCLEO-OUT14A1 is configured to work stand-alone. However, it is possible
to stack two X-NUCLEO-OUT14A1 and enable the related control by enabling the daisy chaining
communication:
– Close J12 [1-2] and J13 [3-4 ] in board #1
– Close J12 [3-4] and J13 [1-2 ] in board #2
– Rework board #1: remove R105 and mount R102
– Rework board #2: remove R119, R108, R107, R104 and mount R102, R113, R111, R109
In terms of software, it is necessary to generate the new binary file after having defined the
preprocessor directive USE_DAISY_CHAIN and removed the directive USE_PAR_IND (or changed
in noUSE_PAR_IND). The modification to control mode becomes effective on the binary files after
rebuilding.
Step 3. Connect the ISO808A-1 device supply voltage via CN1 (see Section 1.3 Power section).
Step 4. Provide the digital supply voltage (see Section 1.2 Digital section).
Step 5. Connect the load on the output connector (see Section 1.3 Power section).
Step 6. Reset the example sequence by pushing the black button on the STM32 Nucleo board.
Step 7. Push the blue button on the STM32 Nucleo board to choose among the examples provided in the
default firmware package.
UM3082
Board setup
UM3082 - Rev 1 page 6/19

2Schematic diagrams
Figure 5. X-NUCLEO-OUT14A1 circuit schematic (1 of 2)
I SO808A- 1 di r ect suppl y vol t age:
- set t o max 3. 3V
when X- NUCLEO- OUT14A1 i s us ded wi t h NUCLEO boar d
- can be set t o max 5. 5V
when X- NUCLEO- OUT14A1 i s us ed st and- al one
( 7V- 12V NUCLEO suppl y vol t age)
def aul t open
Analog supply
10 - 36 V
PA6
PB8
PA8
PA4
PA5
PA3
I OREF
Arduino connectors
def aul t c l osed
DEFAULT
PA10
Al t er nat e use
PB6
PC0
NRST
PB5
PB4
PB9
PB0
PC7
Morpho connectors
(not mounted)
DEFAULT
def aul t open
PA7
PA2
PA1
AVDD
PA0
PA9
PC1
PB10
Al t er nat e use
DEFAULT
DEFAULT
DEFAULT
DEFAULT
DEFAULT
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
PB3
Al t er nat e use
VCC
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
STATUS
OUT_EN
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_SS
PGOOD
DaisyChain
EXT_Vdd
3v3 5v0
R112 100 N.M.
CN4
691214110002
1
2
U2
SM15T39CA
12
CN7
SSQ-119-04-L-D
N.M.
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
CN6
SSQ-108-04-F-S
1
2
3
4
5
6
7
8
R113 100 N.M.
R102 100 N.M.
CN1
691214110002
1
2
R105 100
J9
R116 100 N.M.
CN12
691214110002
1
2
CN3
691214110002
1
2
R119 100
R108 100
D1 STPS1H100A
R103 100
CN2
691214110002
1
2
CN8
SSQ-106-04-F-S
1
2
3
4
5
6
CN11
691214110003
N.M.
1
2
3
R101 100 N.M.
R114 100 N.M.
R117 100 N.M.
C11
4700pF
N.M.
R111 100 N.M.
R120 100 N.M.
CN5
SSQ-110-04-F-S
1
2
3
4
5
6
7
8
9
10
D2
BAT48JFILM
N.M.
U3
ESDA15P60-1U1M
N.M.
C12
4700pF
N.M.
R115 100 N.M.
R104 100
R106 100
TP8
5001
D12
ESDA7P60-1U1M
N.M.
CN9
SSQ-108-04-F-S
1
2
3
4
5
6
7
8
C10
2.2uF
+ C9
47uF
N.M.
12
J5
JUMPER-con2-strip-male
N.M.
R109 100 N.M.
R118 100 N.M.
R107 100
CN10
SSQ-119-04-L-D
N.M.
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
J10
EARTH
STATUS
3V3
5V
VIN
VIN
STATUS
OUT_EN
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_SS
PGOOD
DaisyChain
DaisyChain
SPI_SS
DaisyChain
STATUS
OUT_EN
SPI_SS
STATUS
DaisyChain
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_SS
PGOOD
DaisyChain
OUT_EN
PGOOD
OUT_EN
PGOOD
UM3082 - Rev 1 page 7/19
UM3082
Schematic diagrams

Figure 6. X-NUCLEO-OUT14A1 circuit schematic (2 of 2)
VCC
OUT1
OUT_EN
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
STATUS
SP I_MISO
SP I_MOS I
SP I_S S
Da is yCha in
SP I_CLK
PGOOD
EXT_Vdd
3v3
R1 390
D11
150060RS 75000
AC
C7 10nF
U1
1
NC1
2
Vdd
3
OUT_EN
4
SS
5
CLK
6
SDI
7
PGOOD
8
NC8
9
NC9
10
NC10
11
NC11
12
NC12
13
SDO
14
FAULT
15
GNDdd
16
NC16
17
NC17
18
NC18
19
GNDcc
20
NC20
21
OUT8_2
22
OUT8_1
23
OUT7_2
24
OUT7_1
25
OUT6_2
26
OUT6_1
27
OUT5_2
28
OUT5_1
29
OUT4_2
30
OUT4_1
31
OUT3_2
32
OUT3_1
33
OUT2_2
34
OUT2_1
35
OUT1_2
36
OUT1_1
37
VCC_EP
D9
150060VS75000
AC
J 12
c on4 -2x2 -s trip -ma le
de fault: c los e 1-2
1 2
3 4
C21 33pF
R2 0
C23 33pF
C1 10nF
D5
150060VS75000
AC
D15
150060YS75000
AC
R121
1k
D8
150060VS75000
AC
D4
150060VS75000
AC
C2 10nF
J 7
c on8 -2x4 -s trip -ma le de fault: c los e 1-2, 3-4, 5-6, 7-8
12 34 56 78
R11 390
R15
1k
R25
15k
C5 10nF
R3 0
R20 22k
C13
0.1uF
R26
15k
C3 10nF
R27
15k
C26
0.1uF
C14 33pF
J 3
c on6 -2x3 -s trip -ma le
de fault: c los e 1-2, 3-4, 5-6
1 2
3 4
5 6
R28
15k
J 13
c on4 -2x2 -s trip -ma le
de fault: c los e 1-2
1 2
3 4
D7
150060VS75000
AC
C22 33pF
D3
150060VS75000
AC
J 4
c on6 -2x3 -s trip-m a le
de fault: c los e 5-6
1 2
3 4
5 6
R10 390
R29
15k
C24 33pF
D10
150060VS75000
AC
J 6
c on8 -2x4 -s trip -ma le
de fault: c los e 1-2, 3-4, 5-6, 7-8
12 34 56 78
R30
15k
R8 390
R17
390
R18
15k
R9 390
D13
S MBJ 5. 0A-TR
R19
15k
D16
150060RS75000
AC
C6 10nF
C8 10nF
C25
2.2uF
D6
150060VS75000
AC
R14 22k
C4 10nF
SP I_MOS I
Da is yCha in
SP I_MISO
Da is yCha in
ISO808ATR-1
UM3082 - Rev 1 page 8/19
UM3082
Schematic diagrams

3Bill of materials
Table 3. X-NUCLEO-OUT14A1 bill of materials
Item Q.ty Ref. Part/value Description Manufacturer Order code
1 8 C1 C2 C3 C4
C5 C6 C7 C8
10nF 0603
(1608 Metric)
50V 10%
CAP CER
10000PF 50V
X7R 0603
Wurth
Electronics Inc. 885382206002
2 0 C9 47uF Radial,
Can 100V 20%
CAP 47 UF
20% 100 V (not
mounted)
Wurth
Electronics Inc. 860040875002
3 1 C10
2.2uF 1206
(3216 Metric)
100V 10%
CAP CER
2.2UF 100V
X7R 1206
AVX
Corporation 12061C225KAT2A
4 0 C11 C12
4700pF 1825
(4564 Metric)
3000V (3kV)
10%
CAP CER
4700PF 3KV
X7R 1825 (not
mounted)
Vishay Vitramon HV1825Y472KXHATHV
5 2 C13 C26
0.1uF 0805
(2012 Metric)
100V 10%
CAP CER
0.1UF 100V
X7R 0805
Wurth
Electronics Inc. 885012207128
6 5 C14 C21 C22
C23 C24
33pF 0402
(1005 Metric)
10V 5%
CAPACITOR
CERAMIC SMD
0402
Wurth
Electronics Inc. 885012005010
7 1 C25
2.2uF 0402
(1005 Metric)
10V 20%
CAP CER
2.2UF 10V X5R
0402
Wurth
Electronics Inc. 885012105013
8 5 CN1 CN2 CN3
CN4 CN12
691214110002
7.4X7 pitch 3.5
TERM BLK
2POS SIDE
ENT 3.5MM
PCB
Wurth
Electronics Inc. 691214110002
9 1 CN5 10 ways, 1 row
CONN RCPT
10POS 0.1
GOLD PCB
SAMTEC
4UCON ESQ-110-14-T-S 17896
10 2 CN6 CN9 8 ways, 1row
CONN RCPT
8POS 0.1
GOLD PCB
SAMTEC
4UCON ESQ-108-14-T-S 15782
11 0 CN7 CN10
CONN RCPT
38POS 0.1
GOLD PCB (not
mounted)
Samtec Inc. SSQ-119-04-L-D
12 1 CN8 6 ways, 1 row
CONN RCPT
6POS 0.1
GOLD PCB
SAMTEC
4UCON ESQ-106-04-T-S 15781
13 0 CN11
691214110003
10.5X7.4 pitch
3.5mm
TERM BLK
3POS SIDE
ENT 3.5MM
PCB (not
mounted)
Wurth
Electronics Inc. 691214110003
14 1 D1
STPS1H100A
DO-214AC,
SMA 1A
DIODE
SCHOTTKY
100V 1A SMA
ST STPS1H100A
15 0 D2
BAT48JFILM
SC-76,
SOD-323
750mV @
200mA 350mA
(DC)
DIODE
SCHOTTKY
40V 350MA
SOD323 (not
mounted)
ST BAT48JFILM
UM3082
Bill of materials
UM3082 - Rev 1 page 9/19

Item Q.ty Ref. Part/value Description Manufacturer Order code
16 8 D3 D4 D5 D6
D7 D8 D9 D10
LED GREEN
0603 (1608
Metric) 20mA
LED GREEN
CLEAR 0603
SMD
Wurth
Electronics Inc. 150060VS75000
17 2 D11 D16
RED LED 0603
(1608 Metric)
20mA
LED RED
CLEAR 0603
SMD
Wurth
Electronics Inc. 150060RS75000
18 0 D12 ESDA7P60-1U1
M 2-UDFN
TVS DIODE
5VWM 11.6VCL
1610 (not
mounted)
ST ESDA7P60-1U1M
19 1 D13
SMBJ5.0A-TR
DO-214AA,
SMB 600W
TVS DIODE 5V
13.4V SMB ST SMBJ5.0A-TR
20 1 D15
LED YELLOW
0603 (1608
Metric) 20mA
LED YELLOW
CLEAR 0603
SMD
Wurth
Electronics Inc. 150060YS75000
21 1 J3 con6-2x3-strip-
male
CONN
HEADER .100
DUAL STR
6POS
Wurth
Electronics Inc. 61300621121
22 1 J4 con6-2x3-strip-
male
CONN
HEADER .100
DUAL STR
6POS
Wurth
Electronics Inc. 61300621121
23 0 J5 JUMPER-con2-
strip-male
JUMPER-
CONN
HEADER .100
STR 2POS (not
mounted)
Wurth
Electronics Inc. 61300211121
24 2 J6 J7 con8-2x4-strip-
male
CONN
HEADER VERT
8POS 2.54MM
Wurth
Electronics Inc. 61300821121
25 2 J9 J10 JUMPER-con2-
strip-male
JUMPER-
CONN
HEADER .100
STR 2POS
Wurth
Electronics Inc. 61300211121
26 2 J12 J13 con4-2x2-strip-
male
CONN
HEADER .100
DUAL STR
4POS
Wurth
Electronics Inc. 61300421121
27 5 R1 R8 R9 R10
R11
390 0402 (1005
Metric) 0.1W,
1/10W 5%
CHIP
RESISTOR
SMD 5% 1/10W
0402
Panasonic ERJH2GJ391X
28 2 R2 R3
0 0402 (1005
Metric) 0.1W,
1/10W 0%
CHIP
RESISTOR
SMD 0% 1/10W
0402
Panasonic ERJH2G0R00X
29 2 R14 R20
22k 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 22K
OHM 1% 1/10W
0603
Yageo RC0603FR-0722KL
30 1 R17
390 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 390
OHM 1% 1/10W
0603
Yageo RC0603FR-07390RL
31 2 R15 R121
1k 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 1K
OHM 1% 1/10W
0603
Yageo RC0603FR-071KL
UM3082
Bill of materials
UM3082 - Rev 1 page 10/19

Item Q.ty Ref. Part/value Description Manufacturer Order code
32 8
R18 R19 R25
R26 R27 R28
R29 R30
15k 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 15K
OHM 1% 1/10W
0603
Yageo RC0603FR-0715KL
33 0
R101 R102
R109 R111
R112 R113
R114 R115
R116 R117
R118 R120
100 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 100
OHM 1% 1/10W
0603
Yageo RC0603FR-07100RP
34 7
R103 R104
R105 R106
R107 R108
R119
100 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 100
OHM 1% 1/10W
0603
Yageo RC0603FR-07100RP
35 1 TP8
5001 0.100" Dia
x 0.180" L
(2.54mm x
4.57mm)
TEST POINT
PC MINI .040"D
BLACK
Keystone
Electronics 5001
36 1 U1 ISO808ATR-1
PowerSO-36
Galvanic
isolated octal
high side smart
power solid
state relay with
SPI interface
ST ISO808ATR-1
37 1 U2
SM15T39CA
DO-214AB,
SMC 1500W
(1.5kW)
TVS DIODE
33.3V 69.7V
SMC
ST SM15T39CA
38 16 N/A 2.54mm Close Jumper Wurth
Electronics Inc. 60900213421
39 0 U3 ESDA15P60-1U
1M 2-UDFN
TVS DIODE
13.2V 22.7V
1610
ST ESDA15P60-1U1M
UM3082
Bill of materials
UM3082 - Rev 1 page 11/19

4Board versions
Table 4. X-NUCLEO-OUT14A1 versions
PCB version Schematic diagrams Bill of materials
X$NUCLEO-OUT14A1 (1) X$NUCLEO-OUT14A1 schematic diagrams X$NUCLEO-OUT14A1 bill of materials
1. This code identifies the X-NUCLEO-OUT14A1 evaluation board first version. It is printed on the board PCB.
UM3082
Board versions
UM3082 - Rev 1 page 12/19

5Regulatory compliance information
Notice for US Federal Communication Commission (FCC)
For evaluation only; not FCC approved for resale
FCC NOTICE - This kit is designed to allow:
(1) Product developers to evaluate electronic components, circuitry, or software associated with the kit to
determine whether to incorporate such items in a finished product and
(2) Software developers to write software applications for use with the end product.
This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all
required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product
not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless
the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit
must operate under the authority of an FCC license holder or must secure an experimental authorization under
part 5 of this chapter 3.1.2.
Notice for Innovation, Science and Economic Development Canada (ISED)
For evaluation purposes only. This kit generates, uses, and can radiate radio frequency energy and has not been
tested for compliance with the limits of computing devices pursuant to Industry Canada (IC) rules.
À des fins d'évaluation uniquement. Ce kit génère, utilise et peut émettre de l'énergie radiofréquence et n'a pas
été testé pour sa conformité aux limites des appareils informatiques conformément aux règles d'Industrie Canada
(IC).
Notice for the European Union
This device is in conformity with the essential requirements of the Directive 2014/30/EU (EMC) and of the
Directive 2015/863/EU (RoHS).
Notice for the United Kingdom
This device is in compliance with the UK Electromagnetic Compatibility Regulations 2016 (UK S.I. 2016 No. 1091)
and with the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012 (UK S.I. 2012 No. 3032).
UM3082
Regulatory compliance information
UM3082 - Rev 1 page 13/19

6References
Freely available on www.st.com:
• ISO808A-1 datasheet
•UM3035: "Getting started with X-CUBE-IPS industrial digital output software for STM32 Nucleo"
•NUCLEO-F401RE documentation
•NUCLEO-G431RB documentation
UM3082
References
UM3082 - Rev 1 page 14/19

Revision history
Table 5. Document revision history
Date Revision Changes
12-Dec-2022 1 Initial release.
UM3082
UM3082 - Rev 1 page 15/19

Contents
1Getting started ....................................................................2
1.1 Overview .....................................................................2
1.2 Digital section .................................................................3
1.3 Power section .................................................................4
1.4 Hardware requirements .........................................................5
1.5 System requirements ...........................................................5
1.6 Board setup ...................................................................6
2Schematic diagrams ...............................................................7
3Bill of materials....................................................................9
4Board versions ...................................................................12
5Regulatory compliance information ...............................................13
6References .......................................................................14
Revision history .......................................................................15
List of tables ..........................................................................17
List of figures..........................................................................18
UM3082
Contents
UM3082 - Rev 1 page 16/19

List of tables
Table 1. NUCLEO-F401RE development board supported IDEs - bin files ...................................6
Table 2. NUCLEO-G431RB development board supported IDEs - bin files...................................6
Table 3. X-NUCLEO-OUT14A1 bill of materials .....................................................9
Table 4. X-NUCLEO-OUT14A1 versions ......................................................... 12
Table 5. Document revision history .............................................................15
UM3082
List of tables
UM3082 - Rev 1 page 17/19

List of figures
Figure 1. X-NUCLEO-OUT14A1 expansion board...................................................1
Figure 2. X-NUCLEO-OUT14A1 expansion board: digital interface section .................................3
Figure 3. X-NUCLEO-OUT14A1 expansion board: power section components ...............................4
Figure 4. X-NUCLEO-OUT14A1 and STM32 Nucleo stack.............................................5
Figure 5. X-NUCLEO-OUT14A1 circuit schematic (1 of 2) .............................................7
Figure 6. X-NUCLEO-OUT14A1 circuit schematic (2 of 2) .............................................8
UM3082
List of figures
UM3082 - Rev 1 page 18/19

IMPORTANT NOTICE – READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other product or service names
are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2022 STMicroelectronics – All rights reserved
UM3082
UM3082 - Rev 1 page 19/19