Steelcase 462 Leap Plus User manual

If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S.Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2005 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Page 1 of 8
939546233 Rev B
462 Leap®Plus Chair Back Assembly Replacement
Lumbar Installation/Replacement
Lumbar Resistance Replacement
or a flat-bladed
screwdriver that is 8"
or longer

Page 2 of 8
939546233 Rev B
Chair Back Replacement
1. Slide seat fully forward while holding the
seat slide lever.
2. Locate the black quick release tab located
on the left hand side of the chair (as you sit in
it) between the plates.
3. Lift the quick release tab while pulling the
seat slide lever and sliding the seat forward.
1
SEAT SLIDE LEVER
2
REAR
FRONT
3
QUICK RELEASE TAB
FRONT REAR

Page 3 of 8
939546233 Rev B
4b
4a
4c
ARM
4. With the arm adjusted all the way up,
remove the outer pod cover and arm by
one of the following methods:
a) For black and midnight colored chairs
pull the pod cover out from the bottom
thus releasing it from the inside cover
and clearing the steel bracket. Slide the
cover up until it is loose around the arm
stalk. Skip to step C for arm removal.
b) For platinum colored chairs gently pry
the pod cap off the pod cover and slide it
up the arm stalk. Push the pod cover
halfway down and follow step C for arm
removal.
c) While holding trigger button use a flat
head screwdriver to deflect snap and
gently remove arm and cover from arm
insert.
Black and Midnight
Platinum
POD COVER

Page 4 of 8
939546233 Rev B
5
5. Unscrew two (2) front
screws to remove the
control cover.
NOTE: After control cover
screws are removed, the
chair back is free to move.
Hold chair back firmly to
avoid possible injury.
CONTROL COVER

Page 5 of 8
939546233 Rev B
9
7. Remove the j-channel from the back channel slot
using a flat-bladed screwdriver to begin the removal
process.
8. Remove (2) screws from back shell located under the
back ribbon.
9. Pull up & out on the cushion to remove the cushion
from the back shell. Be careful not to break the clips on
the back shell.
7b
BACK CHANNEL SLOT
7a ELASTIC BAND ON
BOTTOM OF BACK CUSHION
J-CHANNEL
J-CHANNEL
BACK CHANNEL
SLOT
FLAT-BLADED
SCREWDRIVER
8
BACK RIBBON

Page 6 of 8
939546233 Rev B
10. Pop screw covers out
(10a) and remove upper
pivot screws (10b).
11. Remove lower pivot
screws.
12. Reverse steps to
reassemble.
NOTE: Pod covers and
caps should be
reassembled prior to the
arms.
11
10a
10b

Page 7 of 8
939546233 Rev B
1a
LOOP
PIN
1a
1b
2
ALIGNING PEGS
Lumbar Resistance
Mechanism Replacement
1. Remove two (2) screws (1a)
and knob (1b).
2. Align spring loop with pin
and rotate toward floor (right) to
align and lock in place.
3. Replace two (2) screws
removed in step 1.
LUMBAR
RESISTANCE
KNOB

Page 8 of 8
939546233 Rev B
2
Lumbar Installation
1. Pull back down from bottom.
2. Insert lumbar between
cushion and backshell.
3. Raise one side over tabs
and slide all the way down.
4. Repeat on other side.
5. Slide lumbar toward bottom.
Lumbar Replacement
1. Move lumbar up as high as you can.
2. Tip end so that it dislodges from teeth.
Repeat on the other side.
3. Slide lumbar out from backshell.
4. Follow the above steps to reinstall
lumbar replacement.
1
3
1
3
Tip end to dislodge
from teeth.
2