Steelcase FrameOne User manual

HALF LOOP LEG - RH
HALF LOOP LEG - LH
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2012 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
Page 1 of 8
939500590 Rev F
OPEN LOOP LEG - RH
OPEN LOOP LEG - LH CLOSED LOOP LEG - LH
6mm Hex
CLOSED LOOP LEG - RH
OPEN LOOP LEG
- TETHERED
CLOSED LOOP LEG
- TETHERED
FrameOne™Loop Legs used with Universal Worksurfaces
Mounted to Answer®, Montage®, Tethered or Table Applications
OPEN LOOP LEG
- TABLE
CLOSED LOOP LEG
- TABLE

Page 2 of 8
939500590 Rev F
®
1a
RH
LH
1b
2
ANSWER RH INSTALLATION SHOWN
ANSWER
MONTAGE RH INSTALLATION SHOWN
For Panel-Mounted Open
and Closed Loop Legs
NOTE: The panel must be level prior to
assembling the leg to the panel.
1. Z-shaped hook brackets are used to
connect the leg to the panel. Rotate the hook
bracket until it nests inside the panel slot at
the proper slot locations in the panel (1a).
NOTE: The hook brackets always point
“DOWN”.
NOTE: ”L” (for left hand) & “R” (for right
hand) is indicated on each bracket.
TIP: Place the loop leg with attachment
tabs next to the panel to get an
approximate location where the hook
brackets need to mount into the panel.
For Answer - The upper tab mounts
into the bottom two (2) holes on the hook
bracket. The lower tab mounts into the
top two (2) holes on the hook bracket.
NOTE: Make sure the glides in the loop
leg are screwed all the way in. This
helps prevent difficulty in assembling
the hooks to the panel (1b).
2. Place the attachment tabs on the
loop leg up next to the hook brackets
as shown and install two (2) #10-24 x
3/8” self tapping screws into each hook
bracket.
NOTE: Make sure to adjust the glides
so that the glides are touching the floor.
MONTAGE
MOUNTING HOLES
USED DEPEND ON
THE INSTALLATION

Page 3 of 8
939500590 Rev F
®
Adjusting Leg Angles (Optional)
To adjust leg angle, insert shim from either side
of mounting plate. A maximum of 2 shims are allowed
per mounting plate.

LH
Page 4 of 8
939500590 Rev F
®
3
For Panel-Mounted Open and Closed
Loop Legs (cont.)
3. Install the plastic covers in the four (4) places, per leg,
as shown.
4. Place the worksurface flush with the front face of the
leg (4a). Flush the edge of the leg with the side of the
worksurface (4b). Install twenty-six (26) #10-10 x 1” wood
screws per leg (4c).
5. Worksurfaces need to be leveled front to back.
(Assuming the panel has already been leveled side to
side.) Perform leveling by adjusting the glides.
RH
3
3
4c 4a 4b
FLUSH FLUSH

Page 5 of 8
939500590 Rev F
®
For Tethered Open and Closed Loop Legs
1. Install the plastic covers in the two (2) places, per leg, as shown.
2. Place the worksurface flush with the front face of the leg (2a).
Flush the edge of the leg with the side of the worksurface (2b).
Install twenty-six (26) #10-10 x 1” wood screws per leg (2c).
3. Tethered worksurfaces need to be leveled both front to back &
side to side. Perform leveling by adjusting the glides.
1
2c
2a 2b
FLUSH FLUSH

Page 6 of 8
939500590 Rev F
®
For Table Open and Closed Loop Legs
1. For each table leg: Install the plastic covers in the two (2) places,
per leg, as shown.
2. Place the worksurface flush with the front face of the leg (2a).
Flush the edge of the leg with the side of the worksurface (2b).
Install twenty-eight (28) #10-10 x 1” wood screws per leg (2c).
3. Table worksurfaces need to be leveled both front to back &
side to side. Perform leveling by adjusting the glides.
NOTE: For worksurfaces with a Personal Caddy, the Personal Caddy
understructure support bracing must be installed before the legs.
Refer to assembly direction 939502139.
1
2a 2b
FLUSH FLUSH
2c

Page 7 of 8
939500590 Rev F
®
For Half Loop Legs
1. Install the mounting bracket on the
half loop leg with the provided M10 flat
head screw with 6mm hex drive (1a).
Tighten securely. NOTE: Torque not to
exceed 10 ft-lbs. Make sure the spring
clip on the mounting bracket has been
rotated to the position shown (1b).
2. Install the half loop leg assembly by
angling as shown and inserting the top
hook of the mounting bracket into the
appropriate slot in the panel (2a). Rotate
until the leg is upright (2b). The mounting
bracket should drop down into the slots
in the panel (2c).
RH INSTALLATION SHOWN
LH
RH
1b
1a
2a
2b
2c
MONTAGE RH INSTALLATION SHOWN

Page 8 of 8
939500590 Rev F
®
LH
RH
3
RH INSTALLATION SHOWN
SAFETY CLIP
5a 5b
FLUSH FLUSH
5c
For Half Loop Legs (cont.)
3. Rotate the safety clip into the slot in the
panel.
4. Install the plastic covers in the two (2)
places, per leg, as shown.
5. Place the worksurface flush with the
front face of the leg (5a). Flush the edge of
the leg with the side of the worksurface (5b).
Install twenty-six (26) #10-10 x 1” wood
screws per leg (5c). 4
4
CAUTION
CRUSH HAZARD
Be sure to engage safety
clip. Failure to properly
secure bracket could
result in personal injury.