Steelcase Avenir Movable Walls PFF-16 User manual

If you have a problem, question,
or request, call your local dealer,
or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people
who want to help you.
(Outside the U.S.A., Canada,
Mexico, Puerto Rico, and the
U.S. Virgin Islands, call:
1.616.247.2500)
Or visit our website
www.steelcase.com
Si vous avez un problème, question,
ou la demande, appellent votre
revendeur local, ou
Ligne 1 de Steelcase à
888.STEELCASE (888,783,3522)
pour l'action immédiate par les
personnes qui veulent vous aider.
(en dehors des Etats-Unis, Canada,
Le Mexique, Porto Rico, et
Les ÉTATS-UNIS. Les Îles Vierges,
appel: 1,616,247,2500)
Ou visiter notre website
www.steelcase.com
Si usted tiene un problema, pregunta,
o la petición, llama a su distribuidor
local, o Línea 1 de Steelcase en
888.STEELCASE (888,783,3522)
para la acción inmediata por la
gente que desea ayudarle.
(fuera de los E.E.U.U., Canadá,
Méjico, Puerto Rico, y Los E.E.U.U..
Islas de la Virgen, llamada:
1,616,247,2500)
O visite nuestro website
www.steelcase.com
©1998 Steelcase Inc.
Rapids Grand, MI 49501
U.S.A.
Les ETATS-UNIS.
Los E.E.U.U.
Printed in U.S.A.
Imprimé aux Etats-Unis.
Impreso en los E.E.U.U.
Avenir
Movable Walls
Model:PFF - 16 Standard and power panel flat foot (adjustable)
®
1
of
4
939500814 Rev A
3/16” Allen Wrench
Package Contents
Item No. Name
1(1) Foot Partition
2(1) Foot Base
3(2) Foot Attaching Plates
(Single & Double)
4(4) 1/4 -20 x 3/4” Bolts
5(2) Special 1/4 - 20 x 3/4” Bolts
6Spacer
- CAUTION -
The stabilizer foot is used to stabilize a run of
panels. It is not intended for use on panels that
support hang-on components.
3/8” Socket Wrench
®

2
of
4
939500814 Rev A
1. Secure foot attaching plate (Item 3) Single(Item
6) to bottom of panel assembly with (2) 1/4-20 X
3/4" bolts(Item 5). Refer to Fig. "A". When joining
additional panels posi-tion the attaching plate (Item
3) as shown in Fig. "B". If thepanel is the last panel
in a series of panels place attaching plate(Item 3) in
the manner shown in Fig. "C".
Note: A Standard panel is shown as a typical
installation. Power panels are installed in the same
manner.
FIG A
FIG C
FIG B
6
6
33
NOTE:
Loose spacer is provided to
install when two panels are
connected.
Place spacer on foot attaching
plate and trap with studs from
next panel.
PANEL ASSEMBLY PANEL ASSEMBLY

3
of
4
2. Adjust panel glide for desired height. Now
secure foot base (Item 2) to attaching plate (Item 3)
with (2) bolts (Item 4) do not tighten at this time.
Refer to Fig D
3. Insert foot partition pins (Item 1) into holes on
foot base (Item 2) while at the same time inserting
hanger bracket tabs into panel notches.
NOTE: It may be necessary to adjust hanger
bracket up or down allowing tabs to completely
engage into panel notches.
Locking bolt clockwise, drawing hanger bracket tabs
up in the directions of Arrow “W” and foot partition
(Item 1) down in direction of Arrow “X”. When
locked in place tighten bolts (Item 4.) To remove
foot reverse procedure.
939500814 Rev A
1
W
X
4
2
4
3
2
1
PINS
FIG D
FIG E
FIG F
Adjustment
height
5/8” to 1-5/8”
HOLES
PANEL ASSEMBLY
PANEL ASSEMBLY
LOCKING BOLT
HANGER
BRACKET

4
of
4
939500814 Rev A
- IMPORTANT -
feet as shown in Fig G below.
When your panel is not supported with adjoining furniture
another panel secured at an angle, it is necessary to use (2)
FIG G
PANEL ASSEMBLY
PANEL FOOT
PANEL FOOT