Steelcase FRAMEONE FE-3 User manual

Page 1 of 6
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on One Side
of 90 Degree Table
®
May 2009
FE-3 Screen (Left Hand) + Table
1. Fix the Connection Brackets to the Straight and Corner Bracket
by tightening two M6 screws each as shown
configuration.
Loosen the set screws but do not remove it.
2. Remove both FE-3 screen bottom caps.
2
Slot facing front
FE-3
Screen
1
Loosen Set
screws
Loosen Set
screws
Connection
Bracket
Corner Bracket
Straight Bracket

Page 2 of 6
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on One Side
of 90 Degree Table
®
May 2009
FE-3 Screen (Left Hand) + Table
3. Slide the Straight Bracket into the side slot of the FE-3
Screen as shown.
4. Slide the Corner Screen Bracket into the other side slot of the
FE-3 Screen as shown.
5. Re-install both bottom caps of the FE-3 Screen.
3
4
5

Page 3 of 6
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on One Side
of 90 Degree Table
®
May 2009
FE-3 Screen (Left Hand) + Table
6. Refer to the diagram on the right to define the desired
height for the screen.
7. Align the middle Set Screw to the desired Screen Height
guide hole. Tighten this screw to lock it to the guide hole.
Then, tighten the rest of the Set Screws to secure the bracket.
Align the other bracket to the same height and repeat this step.
Middle
Set Screw
H1080 H1175 H1270
360
411
360
601
455
506
550
411
645
316
740
221
455
316
550
221
HighestLowest
H1080 H1175 H1270 H1365 H1460
HighestLowest
H800 (H771) FE-3 Screen
H1000 (H963) FE-3 Screen
7
6
Screen Height
guide hole
Screen Height Guide Hole
This hole functions as a guide to
determine the overall height of the FE-3
screen installed to the FrameOne desk.
Note:
Lowest Guide Hole = Highest Screen Position

Page 4 of 6
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on One Side
of 90 Degree Table
®
May 2009
FE-3 Screen (Left Hand) + Table
8. Remove the support bracket shown.
9. Position the FE-3 screen to the table.
The screen bracket should be attached to the
understructure of the table.
Make sure that the side of the screen is flush
with the side of the table top. Straight
Bracket
Corner
Bracket
9
8

Page 5 of 6
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on One Side
of 90 Degree Table
®
May 2009
FE-3 Screen (Left Hand) + Table
10. Tighten two M6 screws to the Straight Bracket
through the rectangular plate.
Make sure it is tightly secured.
11. Slide rectangular plate 1 into the Corner Screen
Bracket. Make sure the holes are aligned.
Tighten two M6 screws to the Straight Bracket
through rectangular plate 2.
Make sure it is tightly secured.
Rectangular
Plate 1
Rectangular
Plate 2
11
10

Page 6 of 6
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on One Side
of 90 Degree Table
®
May 2009
FE-3 Screen (Left Hand) + Table
12. View of the completed installation of FE-3 Screen
to a FrameOne 90 degree table.
FE-3 Screen
Straight Bracket
View
Corner Bracket
View