Steelcase FRAMEONE FE-3 User manual

Page 1 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
1. Fix the Connection Bracket to the Corner Bracket
by tightening two M6 screws each.
Install as left and right configuration as shown.
Loosen the set screws but do not remove it.
2. Fix the Connection Bracket to the Straight Bracket
by tightening two M6 screws each.
Install as left and right configuration as shown.
Loosen the set screws but do not remove it.
2
FE-3
Screens
1
Loosen Set
screws
Connection
Bracket
Corner Bracket
Loosen Set
screws
Connection
Bracket
Straight Bracket

Page 2 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
3. Remove all FE-3 screen bottom caps.
3

Page 3 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
4. Slide the Straight Bracket into the side slot of the FE-3
Screen ‘A’ as shown configuration.
5. Slide the Corner Screen Bracket into the other side slot of the
FE-3 Screen ‘A’ as shown.
6. Re-install both bottom caps of the FE-3 Screen A.
4
5
6
FE-3 screen ‘A’

Page 4 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
7. Slide the Corner Bracket into the side slot of the FE-3
Screen ‘B’ as shown configuration.
8. Slide the Straight Screen Bracket into the other side slot of the
FE-3 Screen ‘B’ as shown.
9. Re-install both bottom caps of the FE-3 Screen ‘B’.
9
7
8
FE-3 Screen ‘B’

Page 5 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
10. Refer to the diagram on the right to define the desired
height for the screens.
11. Align the middle Set Screw to the desired Screen Height
guide hole. Tighten this screw to lock it to the guide hole.
Then, tighten the rest of the Set Screws to secure the bracket.
Align the other bracket to the same height and repeat this step.
Define the height for the other screen with this same step.
H1080 H1175 H1270
360
411
360
601
455
506
550
411
645
316
740
221
455
316
550
221
HighestLowest
H1080 H1175 H1270 H1365 H1460
HighestLowest
H800 (H771) FE-3 Screen
H1000 (H963) FE-3 Screen
Middle
Set Screw
11
10
Screen Height
guide hole
Screen Height Guide Hole
This hole functions as a guide to
determine the overall height of the FE-3
screen installed to the FrameOne desk.
Note:
Lowest Guide Hole = Highest Screen Position

Page 6 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
12. Remove the support bracket.
13. Position the FE-3 screen ‘A’ and ‘B’ to the table.
The screen brackets should be attached to the
understructure of the table.
Make sure that the sides of the screens are flush
with the sides of the table top. Straight
Bracket
Corner
Bracket
FE-3 Screen ‘A’ FE-3 Screen ‘B’
13
12

Page 7 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
14. Tighten two M6 screws with its rectangular
plate on each bracket as shown.
Make sure it is fixed securely.
M6 Screw
M6 Screw M6 Screw
Rectangular Plate
Rectangular Plate Rectangular Plate
14

Page 8 of 8
FRAMEONE
Assembly Instruction - 800/1000H FE-3 Screen on Both Sides
of 90 Degree Table
®
May 2009
FE-3 Screens + Table
15. View of the completed installation of FE-3 Screens
to a FrameOne 90 degree table.
15