Steelcase 9000 Series Firmware update

Steelcase, Inc.
Grand Rapids, MI 49501
U.S.A.
1-888-783-3522
Tools
Assembly Directions Printed In U.S.A.
REV
93-9501112 A
Page 1 of 4
Tackboard Installation To Series 9000®Furniture (Type Three)

Assembly Directions
93-9501112 REV A Page 2 of 4
NOTE: All tackboards attach with pressure sensitive pads on backs. Listed below is a chart to show you the style number,
size, and standard Series 9000 furniture units to which these style tackboards can be attached.
Style Number Overall Size To Be Used With
99503
99504
99505
99506
99507
99508
99511
99512
99533
99534
45” W. x 44” H.
60” W. x 44” H.
70” W. x 44” H.
45” W. x 56” H.
60” W. x 56” H.
70” H. x 56” H.
75” W. x 44” H.
75” W. x 56” H.
60” W. x 44” H.
60” W. x 56” H.
Tackboard package for use with #9014-D, -G
Tackboard package for use with #9018-E, -H;
any #9040 unit with overhead storage cabinets
As above, for use with #9022-E, -H
Tackboard package for use with #9015-D, -E, -G
Tackboard package for use with #9019-G, -H, -I,
-J; any #9041 unit with overhead storage cabinets;
any #9061 unit with overhead storage cabinets.
As above, for use with #9023-G, -H, -J
Tackboard package for use with any #9044 unit with
overhead storage cabinets
As above, for use with any #9045 unit with overhead
storage cabinets
Tackboard package for use with any #9040 unit with
overhead storage cabinets.
As above, for use with any #9041 unit with overhead
storage cabinets

Assembly Directions
93-9501112 REV A Page 3 of 4
1. Installing upper and lower channels
Remove protective paper and position channels.
Channels must be located 1” from rear edge of
work surface and 1” in from back of upper cases.
After properly locating channels, press down to
case and work surface. NOTE: Only one attaching
channel is used when installing a tackboard filler
on 53” high units. This channel is used on the
work surface.
2. Inner tackboard installation
Remove protective paper from attaching pads on
back of tackboards. NOTE: tackboards should be
installed with metal pull tabs at the top. From
front side of furniture unit, slide bottom edge of
tackboard on top of worksurface until it touches
bottom channel. Lift tackboard into upright position
and press into place. NOTE: If you have a 53” high
unit, install the small tackboard filler in the same
manner. Attaching pads must be adjacent to
work surface.
INNER
TACKBOARD
ATTACHING
CHANNEL
FRONT
FRONT
BACK
BACK
UPPER
CHANNEL
NOT USED
ON 53”
HIGH UNITS
TAPE
ATTACHING
CHANNEL
FRONT
ATTACHING
CHANNEL
ADJUSTABLE
SQUARE SET
AT ONE INCH
DIMENSION
BOTTOM OF
UPPER CASES
1”
BACK OF
UPPER CASES
ATTACHING
CHANNEL
NOTE: UPPER
CHANNEL
NOT USED
ON 53”
HIGH UNITS

Assembly Directions
93-9501112 REV A Page 4 of 4
4. Rear tackboard installation
Remove protective paper from attaching pads on back of one tackboard. Position tackboard to back of furniture
unit by placing outer edge of tackboard against end panel trim and the top edge at the tangent point of top case
radius. This is approximately 1/2” below the top of case. Press tackboard to back of cases to adhere attaching
pads. Remove protective paper from attaching pads and install second tackboard by placing its side edge to the
side edge of installed tackboard. Be sure top edges line up. Press tackboard to back of cases to adhere attach-
ing pads. This completes the installation.
TACKBOARD
TACKBOARD
TACKBOARD
BACK OF
UPPER CASE
1/2”