Stratasys F3300 Operating instructions

Part No. 413183-0001_REV_A
F3300®
3D Printer
Site Preparation Guide

Site Preparation Guide
Page ii
Copyright
Copyright © 2023 Stratasys Ltd. All rights reserved.
This documentation contains proprietary information of Stratasys Ltd. This information is supplied solely to
assist authorized users of this Stratasys 3D printing system. No part of this document may be used for other
purposes, and it may not be disclosed to other parties. The specifications on which this document is based
are subject to change without notice. No part of this book may be reproduced in any form or by any means,
nor stored in a database or retrieval system, without prior permission in writing from Stratasys Ltd.
If this document is distributed as a PDF file, you may print it for internal use.
Part No. 413183-0001_REV_A
Liability
Stratasys shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material. Stratasys makes no warranty of any kind
with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. It is the responsibility of the system owner/material buyer to determine that Stratasys
material is safe, lawful, and technically suitable for the intended application as well as identify the proper
disposal (or recycling) method consistent with local environmental regulations. Except as provided in
Stratasys' standard conditions of sale, Stratasys shall not be responsible for any loss resulting from any use of
its products described herein.
Trademarks
Stratasys, GrabCAD, Insight, and FDM are trademarks of Stratasys and/or subsidiaries or affiliates and may
be registered in certain jurisdictions. All other product names and trademarks cited in this book are the
property of their respective owners.

Page iii
Contents
Revision Log ................................................................................................. iv
Safety............................................................................................................ iv
Safe Environment................................................................................................................ iv
About the F3300 Printer................................................................................. 1
Components ........................................................................................................................ 1
Highlights............................................................................................................................. 1
How to Use This Guide........................................................................................................ 1
Site Preparation Tasks................................................................................... 2
Selecting the Installation Site .............................................................................................. 2
Physical Specifications and Space Requirements .............................................................. 2
Environmental Requirements .............................................................................................. 5
Electrical Requirements ...................................................................................................... 6
Compressed Air Requirements ........................................................................................... 7
LAN Requirements .............................................................................................................. 9
Workstation Requirements .................................................................................................. 9
Preparing for Installation.............................................................................. 10
Inspect Crate for Damage ................................................................................................. 10
Required Tools and Equipment ......................................................................................... 10
Moving the Crated Printer ................................................................................................. 10
Unpacking the Printer......................................................................................................... 11
Electrical Service Connection ...................................................................... 22
Site Preparation Checklist ........................................................................... 24
Electrical Installation Requirements .................................................................................. 24
Environmental Requirements ............................................................................................ 24
Required Installation Tasks................................................................................................ 24

Site Preparation Guide Revision Log
Page iv
Revision Log
The following table lists the main changes in each revision of this document.
Safety
The following basic safety tips are given to ensure safe installation, operation, and
maintenance of Stratasys equipment and are not to be considered as comprehensive on
matters of safety. Although the F3300 printers are designed to be safe and reliable, access to
areas of the printer are potentially dangerous.
Safe Environment
• Connect equipment to a grounded facility power source. Do not defeat or bypass the
ground lead.
• Know the location of equipment branch circuit interrupters or circuit breakers and how to
turn them on and off in case of emergency.
• Know the location of fire extinguishers and how to use them. Use only ABC type
extinguishers on electrical fires.
• Know local procedures for first aid and emergency assistance at the customer facility.
• Use adequate lighting at the equipment.
• Maintain the recommended range of temperature and humidity in equipment area.
• Do not use this product in an environment containing volatile or flammable compounds.
Translations of this guide are updated periodically. If you are consuming a translated version, please
check the English version for the latest revision and list of updates.
Revision Date Description of Changes
A November 2023 First release of this document.

Site Preparation Guide About the F3300 Printer
Page 1
About the F3300 Printer
The Stratasys F3300 3D printer is the first product in a new F3000 series platform. The F3300
is a multi-extruder Fused Deposition Modeling (FDM) printer designed for the smart
manufacturing floor. It incorporates the latest in innovative technology to provide leading FDM
performance in throughput, part quality and reliability. It can produce jigs, fixtures and
production parts that exceed expectations in build time, cost and quality. It will also allow users
to achieve results in ROI with traceability, data analytics and future expansion possibilities. The
Stratasys F3300 printer provides advanced 3D printing for intelligent industrial performance.
Components
• The F3300 printer
• Welcome kit (containing documentation on how to download your user guide and common
tools for maintaining the printer)
• GrabCAD Print and/or Insight software package
• A computer workstation for preparing build files (not sold by Stratasys)
Highlights
• Maximum build area of 600 x 600 x 800 mm (23.6 x 23.6 x 31.5 inch)
• Integrated tool changer with capacity for four extruders
• Four heated material bays
• Automatic calibration
• Large touchscreen graphical user interface
• Two internal cameras for remote monitoring
How to Use This Guide
This guide provides information for selecting an appropriate location for the F3300 printer. This
guide also provides instructions for unpacking and preliminary set-up. Information of special
importance is presented in one of three formats:
A Warning: indicates a procedure that may cause injury to an operator if the
procedure is not followed.
A Warning: will precede the paragraph of instruction to which it relates.
A Caution: indicates a procedure that may cause damage to equipment if the
procedure is not followed.
A Caution: will precede the paragraph of instruction to which it relates.
A NOTE is used to highlight a specific point or to provide an operational tip. While
useful, a NOTE does not indicate a procedure that can cause injury or damage if it is
not followed.
A NOTE will follow the paragraph of instruction to which it relates.

Site Preparation Guide Site Preparation Tasks
Page 2
Site Preparation Tasks
Selecting the Installation Site
Decide where to install the printer based on the following:
1. Space Requirements
2. Environmental Requirements
3. Electrical Requirements
4. Compressed Air Requirements
5. LAN Requirements
Physical Specifications and Space Requirements
Dimensions and Weights
Make sure that the installation site floor space can accommodate the printer’s weight and
dimensions, plus required clearances. The installation location must be a flat level surface that
is stable and capable of holding 1452 kg (3200 lbs).
The F3300 printer does not have casters. Due to the size of the printer, a forklift
is required to move the crated system to an un-boxing location and to the final
selected installation site.
The F3300 printers are capable of generating vibrations depending mainly on
part build geometry and material characteristics. This consideration will need to
be taken into account if locating the printer near vibration sensitive equipment.
Warning:
Due to the physical size and weight of the F3300 printer, it is required to use a
forklift or pallet jack when moving the printer.
Description Weight Dimensions
Printer Crated 1724 kg (3800 lbs)
Width: 243.8 cm (96 in)
Depth: 203.2 cm (80 in)
Height: 254.5 cm (100.2 in)
Printer
Uncrated 1360 kg (3000 lbs)
Width: 203.2 cm (80 in)
Depth: 162.6 cm (64 in)
Height:
• Without light tower: 218.4 cm (86 in)
• With light tower: 236.2 cm (93 in)

Site Preparation Guide Site Preparation Tasks
Page 3
Figure 1: F3300 Printer Overall Dimensions
Figure 2: Printer Center of Mass

Site Preparation Guide Site Preparation Tasks
Page 4
Minimum Operational Clearances
Sufficient side clearances allow for proper air circulation and maintenance access, while the
recommended front and rear clearances also allows enough room to open doors to the oven
and electronics bay. The top hinged covers require additional overhead clearance to fully open.
Figure 3: Minimum Clearances
Side Clearance Minimum 36 inches (91.4 cm) on each side
Rear Clearance Minimum 36 inches (91.4 cm)
Front Clearance Minimum 50 inches (127 cm)
Overhead Clearance Minimum 20 inches (50.8 cm)
127 cm
[50 in]
Rear
91.4 cm
[36 in]
91.4 cm
[36 in]
Front
Overhead 50.8 cm
[20 in]
91.4 cm
[36 in]

Site Preparation Guide Site Preparation Tasks
Page 5
Environmental Requirements
• Printer shipping temperature shall be in the range of -40°C to 70°C (-40°F to 158°F). In
freezing temperatures, bring the printer indoors and leave crated until the it reaches room
temperature.
• Air quality conditions with excessive solid particulates (conductive or non-conductive) may
result in system damage.
• Air quality conditions in which airborne oils are allowed to accumulate on or within the
printer can damage the plastic components.
• System operating temperature shall be in the range of 15°C to 30°C (60°F to 86°F), with
relative humidity range of 20% to 80% non-condensing.
• System storage temperature shall be in the range of 0°C to 35°C (32°F to 95°F), with
relative humidity range of 20% to 90% non-condensing.
• Altitude shall not exceed 3000 m (9843 ft).
• Material storage shall be in the range of 13°C to 30°C (55°F to 86°F), with relative humidity
less than 70%.
• Noise emission (acoustic): <65dBA when idle and when building
Heat Output
TBD
Power Consumption
TBD

Site Preparation Guide Site Preparation Tasks
Page 6
Electrical Requirements
The facility power is required to meet the following power quality and nominal voltage
requirements:
• 50 Hz/ 60 Hz dedicated circuit (47 to 63 Hz)
• 3-phase, 5-wire wye (L-L-L-N-G), 208VAC, 30A circuit with frequency range (47-63Hz.)
• Input voltage tolerance is ±10% from nominal (187 to 229VAC)
• Peak operating current: 23A
• Dedicated circuit: 30 A
• Leakage (touch) current: <1.0mA (under all conditions)
• Site must include a disconnecting means that is readily accessible and within sight of the
printer during operation. Possible connection methods include cord and plug attachment or
direct wiring.
• The connection method and required disconnecting means shall be installed in accordance
with all applicable electrical codes and approved by the authority having jurisdiction.
• Site must be equipped with appropriate lockout tagout kit for equipment.
Operation of the system outside this range is not recommended and degradation of the system
performance and shortened component life expectancy will be experienced.
The system is to be operated on a 3-phase service meeting the recommendations for power
quality given in IEEE Standard 141-1993. Facilities who are unsure of their power quality
should contact their service provider.