Sunjoy L-GZ459PAL-D User manual

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The final
product will be a quality piece that will go together smoothly and give years of enjoyment.
All you will need is a screwdriver, a hammer and two ladders whose height is no less than 2.5m.
Note: THIS UNIT IS HEAVY!
Do NOT assemble this item alone for safety. Four people are necessary.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in which the
part is used
AssemblyInstructions
Item: L-GZ459PAL-D

Screen 1 A 2
Screen 2 B 2
Side panel 1 C 2
Side panel 2 D 2
Roof support frame E 2
Pothook beam F 1
Pothook G 2
Small top roof panel H 2
Big top roof panel I 2
Cover plate J 1
Slate top K 2
Shelf L 2
Support piece M 12
LED Light N 1
Remote control O 1
Parts List

AA M6X15 Bolt 16PCS
I I M6X20 bolt 4PCS
BB M6 flat washer (Bigger) 32 PCS
CC M6X35 bolt 8 PCS
Z M6 wrench 1 PC
Hardware Pack 1
Fig.1: Insert screen (A & B) to roof panel
(E), fix them with bolt (AA) and washer
(BB), fix bottom hole with bolt (II) and
washer (BB) (Note: Put the parts on the
ground evenly.)
Fig.2: Fix side panel C (D) to screen B (A)
with bolt (CC) and washer (BB). (Note:
Connect C to B and D to A.)

I I M6X20 bolt 2PCS
BB M6 flat washer (bigger) 34 PCS
HH M6X15 bolt 24PCS
DD M6X35 bolt 8 PCS
Hardware Pack 2
Fig.3
Fig.4

Fig.3: Attach pothook (G) to pothook beam (F), then fix pothook beam (F) to the top of roof panel (E) with bolt
(II) and washer (BB).
Fig.4: Attach support piece (M) to screen A (B) & side panel C (D) with bolt (HH) and washer (BB). Then place
slate top (K) to side panel (D & C) & support piece (M), fix them with bolt (HH) and washer (BB).
Fig.5: Fix shelf (L) to the middle of screen (A & B) with bolt (DD) and washer (BB).
EE M6X30 bolt 16PCS
BB M6 flat washer (bigger) 18 PCS
FF M6X40 bolt 2 PCS
GG ￠8*180 peg 8 PCS
Hardware Pack 3

BATTERY/LIGHTING UNIT INSTRUCTIONS:
1. Six AAA batteries are sold separately.
2. When you install the batteries of light, screw off handle of the light, and move the cover on the top of the light.
Put the batteries to battery compartment and align batteries according to the labeling as Fig.1. Then close the
battery cover, screw on the handle and tighten.
3. When you install the batteries of remote control, open the battery cover according to labeling on battery
compartment. Then put the batteries to battery compartment and align batteries according to the labeling as Fig.2.
4. Switch the light unit on/off by remote control and extra long chain on the bottom of the light.
SAFETY INFORMATION!
WARNING:
Do not mix old and new batteries. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium)
batteries.
If you find any noise, excessive temperature or leakage from a battery, please discard.
When not using the unit for a considerable period of time, disconnect the batteries from the unit for storage.
If battery power is weak during use, switch off the device and dispose of batteries.
Fig.6: Attach small top roof panel (H) to roof panel (E) with bolt (EE) and washer (BB).
Fig.7: Attach big top roof panel (I) to roof panel (E) with bolt (EE) and washer (BB).
Fig.8: Attach cover plate (J) to pothook beam (F) with bolt (FF) and washer (BB). Hang LED light (N) to the
pothook (G) when use.
Fig.9: Fix assembled gazebo to grass ground with peg (GG).

Fig.10: Hang assembled light (N) on pothook (G)
when use.

IMPORTANT:
1. Keep all children and pets away from assembly area. Children and pets should be supervised when they are in
the area of gazebo construction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Four people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to reduce the risk
of personal injury and damage to equipment. Please read all instructions before assembly and use.
6. For outdoor use only. Install on level ground. Stakes are provided to secure the gazebo in the ground. If you wish
to secure the gazebo to a wood deck or concrete surface, you will need to purchase fasteners appropriate for these
surfaces. These are readily available at your local hardware store or home center.
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for, or
otherwise regulate, installation and use.
9. While this gazebo is manufactured to withstand gale force winds utilizing only the supplied ground stakes, in
areas subject to frequent severe weather, securing the gazebo to a deck, concrete patio or footings should be
considered.
10. Your gazebo has been engineered to accommodate winter snow loads incurred in most areas. Removal of
accumulated snow on the gazebo roof with a roof rake is recommended. In areas that are regularly subject to
blizzard conditions however, removal of the roof panel is suggested. The assembled roof structure can simply be
left in tact until warmer conditions return.
Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of
your item provided the item is maintained with care and used only for personal, residential purposes. The item is
warranted to be free from defects in material or workmanship for a period of 1 year. If any defect is found, please
call our customer service department at 1-866-578-6569 for assistance. Transportation, delivery costs, or
compensation for assembling or disassembling the product are not covered by the warranty. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
Please do not return this product to the store. For technical assistance on assembly or replacement
parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am EST to 8:00 pm PST or fax the
replacement part form which is in the box to 1-740-283-3549 or Email [email protected]
for assistance.
Made
2016-4
in China