Sunjoy L-GZ605PST-A1 User manual

Assembly Instructions
Item: L-GZ605PST-A1
DO NOT REMOVE THE PROTECTIVE FILM ON THE PC TOP PANELS UNTIL
INSTALLATION. MAKE SURE TO PUT THE UV PROTECTED SIDE FACING UP. IT IS A
VERY IMPORTANT PROCEDURE; IF NOT FOLLOWED AS DESCRIBED, YOUR ROOF
WILL NOT BE COVERED BY THE GUARANTY.

GAZEBO ASSEMBLY INSTRUCTIONS
Our clear, easy-to-follow, step-by-step instructions will guide you through the
project from start to finish. The final product will be a quality piece that will give
you years of enjoyment.
All you will need is a screwdriver, a hammer and two ladders of at least 8 feet
(2.5 m) high (not included).
Note: THIS UNIT IS HEAVY!
DO NOT assemble this item alone for your safety. Six people are necessary for
smooth & safe installation.
Item identification: For ease of identification, all parts are labeled to correspond
to the Step number in which the part is used.

Front post 1 A1 1
Front post 2 A2 1
Back post 1 A3 1
Back post 2 A4 1
Side beam 1 B1 1
Side beam 2 B2 1
Decorative slot 1 C1 1
Decorative slot 2 C2 1
Junction bar D 1
Back beam 1 E1 1
Back beam 2 E2 1
Beam junction F 2
Middle beam 1 G1 1
Middle beam 2 G2 1
Small beam 1 H1 2
Small beam 2 H2 2
Small beam
junction I 2
Back card slot 1 J1 1
Back card slot 2 J2 1
Front card slot 1 K1 2
Parts List

Front card slot 2 K2 1
Edge beam 1 L1 1
Edge beam 2 L2 1
Middle beam L3 4
PC panel 1 M1 10
PC panel 2 M2 1
PC panel 3 M3 1
PC panel 4 M4 1
PC panel 5 M5 1
PC penal card slot N 5
Side card slot 1 N1 1
Side card slot 2 N2 1
Post base 1 O1 2
Post base 2 O2 2
Post base cover 1 P1 2
Post base cover 2 P2 2
Curtain-mounting tab Q 4
Middle beam bracket R 2
Connecting piece 1 S1 12
Connecting piece 2 S2 4

Connecting piece 3 S3 1
Connecting piece 4 S4 1
Bracket 1 T1 1
Bracket 2 T2 1
Bracket 3 T3 4
Corner support U 2
Mosquito screen V 1
Curtain W 1
AA Bolt M6X20 4PCS
BB Flat washer M6 74PCS
CC Bolt M6X15 38PCS
DD Nut M6 2PCS
FF Bolt M6X15 24PCS
GG Bolt M6X35 4PCS
HH Bolt M6X15 26PCS
Z1 Wrench M6 2PC
Z2 Wrench M6 1PC
Hardware Pack 1

Fig.1: Install the curtain-mounting tab (Q) to back post 1 (A3) and back post 2 (A4) with bolt (AA) and
flat washer (BB). Ensure the narrow surface of the curtain-mounting tab (Q) faces the post with three
holes.
Fig.2: Set the post base cover 1 (P1) into the back post 1（A3）and back post 2 (A4), then secure post
base 1 (O1) to post 4 (A4) and post 3 (A3) with a bolt (HH) and flat washer (BB). Ensure the flat
surface of the base 1 (O1) and post base cover 1 (P1) face the post with three holes.
Fig.3: Set the post base cover 2 (P2) to the front post 1 (A1) and front post 2(A2), then secure the post
2 (O2) to front post1 (A1) and front post 2(A2) by using bolt (HH) and flat washer (BB).
Fig.4: Install the plastic rings (EE) into decorative slot 1 (C1) and decorative slot 2 (C2), use 7 plastic
rings for each decorative slot.

Fig.4-1: Insert the junction bar (D) into the decorative slot 1(C1) and decorative slot 2 (C2), and secure
with bolt (CC) and flat washer (BB).
Fig.5: Install the plastic rings (EE) into the runner of side beam 1 (B1) and side beam 2 (B2), 12 plastic
rings for each runner.
Fig.6: Insert the beam junction (F) into back beam 1 (E1) and beam 2 (E2) and secure with bolt (CC),
and flat washer (BB).Install the middle beam 1 (G1) and middle beam 2 (G2) in the same way with
back seam1 (E1) and back seam2 (E2).
Fig.7: Use bolts (FF) to install the complete side beam 1(B1) (or side beam 2(B2)) to front post 1 (A1)
and back post2 (A4)(or front post 2(A2) and back post 1(A3))
Fig.8: Install the complete decorative slot to front post with bolt (GG) and flat washer.
Fig.9: Install the corner support (U) to the corner of front post, and secure them with bolt (HH) and bolt
(BB).
Fig.10: Install the complete back beam to back post with bolt (FF).
Fig.11: Use bolt (HH), flat washer (BB) to install the connecting piece 3 (S3) (or install connecting
piece 4(S4)) to edge beam 1(L1)(or edge beam 2(L2)), then install the complete side beam to post 1
(A1)(or post 2(A2))
Fig.12: Using connecting piece 2(S2), bolt (CC), flat washer (BB) to secure the edge beam 1(L1)(or
edge beam 2(L2)) to back seam. Use bolt (CC) and flat washer (BB) to install middle beam mounting
bracket (R) and middle beam to side beam. Install connecting piece 2 (S2) to the bolt of edge beam
1(L1)(or edge beam 2(L2))’s card slot by using bolt (DD) and flat washer (BB), then use a bolt (CC)
and flat washer (BB) to install connecting piece (2) to middle beam.

BB Flat washer M6 56PCS
CC Bolt M6X15 40PCS
DD Nut M6 4PCS
II Nut M6 12PCS
Hardware Pack 2
Fig.13, Fig.13-1: Insert the PC panel 3 (M3)(or PC panel 5 (M5)) to the card slot of edge beam and side
beam, then insert PC panel 2 (M2)(or PC panel 4(M4)) to the card slot of edge seam and side beam.
Fig.14: Using connecting piece 1 (S1), bolt (CC) and flat washer (BB) to install one side of middle beam
(L3) to back beam.
Fig.14-1: Install the connecting piece 1(S1) to the bolt of middle beam (L3)’s card slot by using bolt CC and
flat washer BB. Use bolt (CC) and flat washer (BB) to install the connecting piece 2 (S2) to middle beam.

Fig.14-3: Install another side of middle beam (L3) to decorative slot by using connecting piece 1(S1),
bolt (CC) and flat washer (BB).
Fig.15: Insert the small beam junction (I) into small beam 1(H1) and small beam 2(H2) and secure
them with bolt CC and flat washer BB.
Fig.15-
1: Set the complete small beam through the 2 group bolts middle beam (L3) and edge
beam(L1) and secure them with nut (II) and flat washer (BB).
CC Bolt M6X15 6PCS
BB Flat washer M6 16PCS
HH Bolt M6X15 4PCS
DD Nut M6 6PCS
JJ Bolt M6X10 6PCS
Hardware Pack 3

Fig.16: Settle back card slot 1 (J1) and back card slot 2 (J2) to edge beam and middle beam, and secure one side of
back card slot to edge beam by using bolt (HH) and flat washer (BB).
Fig.16-1: Use bolt (CC) and flat washer (BB) to secure the back card slot 1(J1) and back card slot 2(J2) to the middle
beam (L3)
Fig.17: Set the side card slot 1 (N1) and side card slot 2 (N2) to side PC panel, and secure them with bolt HH and flat
washer BB.
Fig.18: Insert the PC panel 1(M1) into the slot of middle beam (L3), install the edge beam 1(L1) and edge beam 2(L2)
Fig.18-1: Insert the PC panel (N) into the slot of middle beam (L3), install the edge beam1 (L1) and edge beam2 (L2) the
same way.
Fig.18-2: Insert PC panel 1(M1) into the bottom card slot of middle beam (L3), install edge beam 1(L1) and edge beam
2(L2) the same way.
Fig.19: Insert the bolt (JJ) into the bottom card slot of middle beam (L3), edge beam 1 (L1) and edge beam 2 (L2), then set
the front card slot 1 (K1) to complete bolt (JJ) and insert the front card slot into the PC panel. Install front card slot 2(K2)
the same way, see step 3.
Fig.20: Install the blank 2(T2) to edge beam 2(L2) and front card slot 2(K2), and secure them with bolt DD and flat
washer BB. Same way to install the blank 1(T1) and blank 3(T3), see step 3.
KK Nail Φ8X250MM 14 PCS
LL
Screw M6*80
8PCS
Hardware Pack 4
EE Plastic ring 76PCS
Hardware Pack 5

Warranty
Thank you for purchasing this product. These products have been made to demanding,
high-quality standards and are guaranteed for domestic use against manufacturing faults
for a period of 12 months from the date of purchase.
Important: Please do not return this product to the store. For technical assistance on
assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from
8:00 am EST to 8:00 pm PST or fax the replacement part form which is in the box to
1-740-283-3549 or Email [e-mail] for assistance.
The product is guaranteed for 12 months if used for normal trade purposes. Any warranty
is invalid if the product has been overloaded or subject to neglect, improper use or an
attempted repair other than by an authorized agent. Heavy-duty or daily
professional/commercial usage are not guaranteed. Due to continuous product
improvement, we reserve the right to change the product specifications without prior
notice.
Fig.21: Hang the curtain (W) with the plastic rings (EE) hung on decorative slot and side beam.
Fig.22: Hang the mosquito screen (V) with the plastic rings (EE) hung on decorative slot and side beam.
Fig.23: Raise the post base cover 1 (P1) and assemble ground spike (KK) to the ground through the
post base 1(O1) .
Fig.24: Raise the post base cover 2 (P2) and assemble ground spike (KK) to the ground through the
post base 2(O2) .
Fig.25: Secure the gazebo to the curtain by using bolt (LL)
through curtain-mounting bracket (Q), and screw the bolts in the
curtain-mounting bracket (Q).

SAFETY WARNINGS
1. Keep all children and pets away from assembly area. Children and pets should be supervised
while gazebo is being assembled.
2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction such as fence,
garage, and house, overhanging branches, laundry lines or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe
assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and use.
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the gazebo in the
ground. If you wish to secure the pavilion to a wood deck or concrete surface, 16 anchors are
provided for these surfaces.
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to installing this gazebo. Some jurisdictions
may require permits for installation and use. Some special procedures may be valid in your area.
9. While this gazebo is manufactured to withstand strong force winds through only the supplied
ground stakes, in areas subject to frequent severe weather, securing the gazebo to a deck, concrete
patio or footings should be considered.
NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather conditions
(storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must be cleaned off
regularly. Any damage caused by snow accumulation is not covered by the warranty.
Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that
protects it from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur
once these protective coatings are scratched. This is not a defect and thus not covered by the
warranty.
To minimize this condition, we recommend care when assembling & handling the product to prevent
scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up
with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of common cooking oil. If
surface oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start
dripping on to deck or patio and caused damaging stains, which may be difficult to remove. This can
be prevented if the above-mentioned measures are taken to keep the product from oxidizing.
Made in China

Supplement