Sunricher SR-2850C User manual

RF RGB & Dual Color Wall Mounted Controller 09.2830C.04192
Click or to choose the zone, Touch the sliders to dim CCT
color(if choose CCT color zone) or RGB color(if choose RGB color zone)
Function introduction
Important: Read All Instructions Prior to Installation
Click to turn on/off
Press and hold down to save
color; Click to recall the saved
Click to play / pause the 10
built-in effects, Press and hold
down to speed up/down the
running effect
CCT color zone 1.Click to choose
the zone, Press and hold down to
turn on/off corresponding zone
Press and hold down to
increase/decrease light
intensity
CCT color zone 2.Click to choose
the zone, Press and hold down to
turn on/off corresponding zone
RGB color zone 1.Click to choose
the zone, Press and hold down to
turn on/off corresponding zone
RGB color zone 2.Click to choose
the zone, Press and hold down to
turn on/off corresponding zone
Front side
Back side
60.3 mm
RF Wall
Panel Controller
DC Power input
V- V+
52.0 mm
60.3 mm 52.0 mm
19.4 mm
Product Data
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
Wiring diagram
Output Signal RF signal
Power Supply 12-24VDC
Power consumption 20 mA
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 86x86x29.1mm
• Touch sensitive
• Glass interface(white & black)
• Compatible with all universal series RF receivers, radio frequency: 869.5/434MHz
• Control RGB+CCT color
• Control 4 zone of RF receiver synchronously and separately
• Waterproof grade: Ip20
RF Wall
Panel Controller
V- V+
12-24VDC
PSU
AC 100-240V
DC Version
RF Wall
Panel Controller
AC Version
NL
AC Power input
RF signal
100-240VAC
20 mA
0-40°C
8% to 80%
86x86x29.1mm
DC Version AC Version
DC Version
AC 100-240V
AC Version
RF Wall
Panel Controller
AC Version
NL
AC Power
50/60Hz
AC Power
50/60Hz

Note : only can pair with CCT color lighting. only can pair with LED RGB color lighting. LED
Installation
12-24VDC
Power Supply
DC version needs connect
with DC power supply
Pair with RF receiver
Step 2:Choose and click a zone number(e.g. RGB color zone 2)
Step 1:Click the “Learning Key” button on RF receiver or re-power on the
receiver three times continuously to set it into pairing status
Learning Key
RF LED Receiver
Step 3:Touch the slider, LED lights connected with the RF receiver flicker
once means the receiver is paired with RGB color zone 2 successfully.
Built-in 10 color changing modes are as follows:
Mode 1: Any two colors of RGB mix fade-in & fade-out
Mode 2: RGB three colors mix fade-in & fade-out
Mode 3: RGB three colors mix fade-out & fade-in
Mode 4: RGB flash
Mode 5: RGB three colors fade-in & fade-out successively
Mode 6: RGB three colors fade-in successively
Mode 7: RGB three colors fade-out successively
Mode 8: RGB three colors jump changing successively
Mode 9: R&B two colors mix fade (R in B out), then G fade-in, then R&B mix fade (R out B in), then G fade-out
Mode 10: B fade-out, then G&B mix fade (G out B in), then R&G mix fade (R out G in), then R fade-in
Click the paired zone number/numbers, then touch the slider or the other buttons to do the controlling
Operate the remote after pairing
1. Do wiring the wall panel & RF receiver according to wiring diagram (please refer to the instruction of RF receiver that
you would like to pair with)
2. Power on, then touch the button to turn on the controller, indicator of the controller turned blue
Operation