SunSetter PRO Operating and safety instructions
RETRACTABLE AWNINGS
For Technical Support visit us at www.sunseer.com/ownerscorner
or Call Toll Free 800-670-7071 • Fax 877-224-4944
©SunSeer Products, a Massachuses Limited Partnership, 184 Charles Street, Malden, MA 02148
Motorized PRO Awning
PRO Front Bar Complete Assembly Replacement
*Helpers Needed*
Parts Supplied: PRO Front Bar Housing, six End Plate screws.
WARNING: FAILURE TO FOLLOW THESE PROCEDURES CAN RESULT IN PERSONAL INJURY!! PLEASE READ
THESE INSTRUCTIONS COMPLETELY BEFORE PERFORMING THIS PROCEDURE.
PLEASE NOTE THAT LEFT AND RIGHT REFERENCES ARE AS YOU ARE FACING THE HOUSE.
1.
2.
3. Unplug the power cord from the wall outlet.
4.
5. ONLY the LEFT End
Cap on the LEFT end of the Front Bar (on the opposite
Figure 1.
Note: Do not disturb the RIGHT side End Cap with the
6.
and place in a clean, safe area.
Note
Front Bar. See Figure 2.
Figure 1
Right End Cap
Front Bar Connector,
Front Bar Connector,
present on your Awning.
See Figure 3 and Figure 4.
Figure 4
Figure 3
Figure 2
2
1.
LEFT side of
.
Note
2.
.
3.
Note
pressure.
4. Repeat for the other side.
Note: Be certain to retain the two White Nylon
Bushings that are located in the upper and lower
5.
6.
support or allow it to hang straight down from the
Roller Bar.
Figure 5
Front Bar
Connector
6mm Allen Cap
5mm Allen Cap Bolt
Gear Assembly
Note
damaged while the Front Bar is being replaced!
7.
8.
9. Center the two Front Bars next to each other.
Note
the two Front Bars. Center them as close as possible.
10. Mark the replacement Front Bar with the precise
original Front Bar.
Note: This will ensure the Lateral Arms connect to
the replacement Front Bar with the same alignment
as the original Front Bar. Otherwise, see the
11.
Cap Bolts where the Front Bar Connector clamps
.
12.
13.
replacement Front Bar Assembly, align with the
marks made in Step 10.
14. Repeat for the other Front Bar Connector.
15.
16.
17.
Connectors.
18.
19.
Fabric in the Front Bar and then the Roller Bar.
20.
the Fabric.
21. Replace the End Cap.
22.
the Roller Bar.
23.
24.
in
CONNECTORS.
Figure 6
Front Bar
3
1. Close the Awning all the way.
2. Unplug the motor.
3.
Figure 7.
4.
the Front Bar and the Front Bar Connectors.
5.
Figure 8.
6.
performing the following steps:
7.
Figure 9.
•
Note: A slight tap on the Connectors with a
• Both Arms, at the folded elbow, should be
when released.
Figure 8
Front Bar
Connector
5mm Allen Cap Bolt
on Arm
Closed
Elbow
Figure 7
8.
9.
10.
11. Plug in the motor.
12.
Front Bar
Figure 9
Elbows
House
4
1.
LEFT side of the
Figure 11.
Figure 11
Front Bar
Note
2.
Figure 10.
3.
Note
pressure.
4. Repeat for the other side.
Note: Be certain to retain the White Nylon Bushings
5.
6.
support or allow it to hang straight down from the
Roller Bar.
Note
damaged while the Front Bar is being replaced.
7.
8.
9. Center the two Front Bars next to each other.
Note
the two Front Bars. Center them as close as possible.
10. Mark the replacement Front Bar with the precise
original Front Bar.
Note: This will ensure the Lateral Arms connect to
the replacement Front Bar with the same alignment
as the original Front Bar. Otherwise, see the
11.
Cap Bolts where the Front Bar Connector clamps
Figure 10.
12.
13.
replacement Front Bar Assembly, align with the
marks made in Step 10.
14. Repeat for the other Front Bar Connector.
15.
16.
17.
Figure 10.
18.
19.
Fabric in the Front Bar and then the Roller Bar.
20.
the Fabric.
21. Replace the End Cap.
22.
the Roller Bar.
23.
24.
Bushings
Figure 10
5mm Allen Cap Bolt
5
1. Open the Awning all the way.
2.
the inside Allen Cap Bolt toward the center of the
Figure 13.
3. Close the Awning all the way.
4.
Figure 14.
5.
the Allen Cap Bolt toward the outside edge of the
Figure 13.
6.
the Front Bar.
7.
performing the following steps:
on Arm
Closed
Elbow
Figure 14
Figure 13
Step 2
Front Bar Connectors
Outside
Bolt
Outside
Bolt
Figure 12
Front Bar
Front Bar
Connector
Front Bar
Elbows
Elbows
House
Front Bar
8.
.
•
Note: A slight tap on the Connectors with a
• Both Arms, at the folded elbow, should be
when released.
9.
Figure 13.
10. Figure 14.
11. Open the Awning.
12.
Figure 13.
13. Close the Awning.
14. Plug in the motor.
15.
SunSeer Products, a Massachuses Limited Partnership, 184 Charles Street, Malden, MA 02148
Other SunSetter Accessories manuals
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter VISTA Quick start guide
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter Motorized Series Original instructions
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter Platinum Plus Guide
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter 900XT Use and care manual
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter EASYSHADE Guide
SunSetter
SunSetter EASYSHADE Original instructions
SunSetter
SunSetter 900XT Installation guide
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter Vista Series User manual
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter Motorized PRO Guide
SunSetter
SunSetter Oasis Use and care manual
SunSetter
SunSetter VISTA Operating instructions
Popular Accessories manuals by other brands
Rechner Sensors
Rechner Sensors Capacitive KAS-80 Series instruction manual
PCB Piezotronics
PCB Piezotronics S111A22 Installation and operating manual
sauter
sauter EGQ220F931 Operating Instructions, Mounting & Installation
leco
leco Sunroof Waved manual
STEAMAX
STEAMAX TFV12 BABY PRINCE user manual
AUREL
AUREL MAG 4M 5026 user manual