Target Fairglen TGFGMEDIWH User manual

>>
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
fairglen
media stand
assembly instructions
style # TGFGMEDIWH (white)
dpci # 249-10-2248
TCIN # 54158375

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-15
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 20
wooden dowel
(H2) x 20
cam bolt
(H3) x 20
cam
(H4) x 22
pan head scew
(H5) x 8
shelf support
(H6) x 2
washer
(H7) x 1
wall anchor
(H8) x 1
wall strap
(H9) x 1
truss head screw
(H10) x 1
wall screw

5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side panel 1
C right side panel 1
D left partition 1
E right partition 1
F bottom panel 1
G back panel 1
H adjustable shelf 2
Ixed shelf 1
J sliding door 2
K foot 2

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
4. 5.
1. 2. 3.

step 1: attach left partition and right partition to xed shelf
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
1.1. Carefully tap small wooden dowels into place in left partition and right partition. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in left partition and right partition.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.
7
nished edge

step 2: attach top panel and bottom panel
(H1) x 8
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
2.1. Carefully tap small wooden dowels into place in top panel and bottom panel. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush in top panel and bottom panel.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.
8
nished edge

9
step 3: attach legs
3.1. Align legs with pre-drilled holes to attach to bottom panel.

10
step 4: attach right side panel
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
4.1. Carefully tap small wooden dowels into place in right side panel. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush in right side panel.
4.3. Refer to page 6 for instructions on how to use the cam lock system.
4.4. Do not over tighten bolts.

11
step 5: install sliding doors
5.1. Insert sliding doors into tracks located on top panel and bottom panel.

step 6: attach left side panel
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
6.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
6.2. Screw-In cam bolts must be screwed down ush in left side panel.
6.3. Refer to page 6 for instructions on how to use the cam lock system.
6.4. Do not over tighten bolts.
12
6.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
6.2. Screw-In cam bolts must be screwed down ush in left side panel.
6.3. Refer to page 6 for instructions on how to use the cam lock system.
6.4. Do not over tighten bolts.

step 7: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN DOOR NOT SLIDING SMOOTHLY**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 22
short pan-head
screw
7.1. Make sure the screws go through the pre-drilled holes properly.
7.2. Do not over tighten screws.
13
hole for anti-tip
7.1. Make sure the screws go through the pre-drilled holes properly.
7.2. Do not over tighten screws.
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN DOOR NOT SLIDING SMOOTHLY**

step 8: install adjustable shelves
(H5) x 8
shelf support
8.1. Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
8.2. Angle shelf to t between the rails and set on top of shelf supports.
14
nished edge
nished edge

step 9: install anti-tip kit
(H9) x 1
tuss head
screw
(H8) x 1
wall strap
(H7) x 1
wall anchor
(H10) x 1
wall screw
(H6) x 2
washer
Position against wall
Mark position of strap hole on wall
Drill 1/4” hole
Tap in wall anchor
Fasten anti-tip strap with wall screw
provided
15
(H10)
(H7)
(H6)
(H9)
(H6)
(H8)
adjustable leg levelers
Mark position of strap hole on wall
Fasten anti-tip strap with wall screw
provided

WARNING
   
  

• 
•   
•     
 

•     
 
•    

•   

   
   
  
WARNING
  
60    
 
    

  
    

 
 16840041
1. WARNING - Death or serious injury may occur when children climb on
audio and/or video equipment furniture. A remote control or toys placed
on the furnishing may encourage a child to climb on the furnishing and as a
result the furnishing may tip over on to the child.
2. WARNING - Relocating audio and/or video equipment to furniture not
specically designed to support audio and/or video equipment may result
in death or serious injury due to the furnishing collapsing or over turning
onto a child.
3. This unit has been designed for the weight shown. Exceeding this recom-
mended weight could result in excessive “sagging” of the top. Extreme
overloading can cause failure of the top and possible injury.
4. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray
furniture polish as needed.
16
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
holds at panel TVs
up to 54” or 60 lbs.
30 lbs. per shelf

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.