Target 249-14-0039 User manual

narrow bookcase
>> assembly instructions
style # CANARRBKES (espresso)
dpci # 249-14-0039
tcin # 13556948
style # CANARRBKEB (ebony)
dpci # 249-14-0041
tcin # 13556950
style # CANARRBKMT (midtone cherry)
dpci # 249-14-0366
tcin # 13556937
style # CANARRBKCH (chestnut)
dpci # 249-14-0359
tcin # 13556942
style # CANARRBKWH (white)
dpci # 249-14-0363
tcin # 13556940
style # CANARRBKBR (rustic)
dpci # 249-14-5419
tcin # 53587258
style # CANARRBKGY (gray)
dpci # 249-14-5356
tcin # 53587259
style # CANARRBKWL (walnut)
dpci # 249-14-5357
tcin # 53587257
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-13
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 27
cam
(H2) x 12
shelf support
(H3) x 1
wall anchor
(H4) x 27
cam bolt
(H5) x 20
wooden dowel
(H6) x 27
short pan head screw
(H7) x 4
small at head screw
(H8) x 1
38mm wall screw
(H9) x 1
wall strap
(H10) x 1
19mm pan head screw
(H11) x 2
5/8” washer

5
exploded diagram
ITEM DESCRIPTION QUANTITY
Dmiddle back xed stretcher 1
E top front stretcher 1
F decorative molding 1
Kmiddle front xed stretcher 1
L adjustable shelf stretchers 3
M bottom front stretcher 1
O adjustable shelves 3
Pmiddle xed shelf 1
Q bottom panel 1
R back panel 1
X right side panel 1
Y left side panel 1
Z top panel 1

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
1. 2. 3.
4. 5.

step 1: prepare xed shelves. attach shelves and top front rail to left side panel.
(H1) x 11
cam
(H5) x 9
wooden dowel
(H4) x 11
cam bolt
1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.
7
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

step 2: attach right side panel
(H1) x 5
cam
(H5) x 6
wooden dowel
(H4) x 5
cam bolt
2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.
8
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
Screw-In cam bolts must be screwed down ush.
Refer to page 6 for instructions on how to use the cam lock system.

9
step 3: attach decorative molding
(H7) x 4
small at head
screw
3.1.
Align screws with pre-drilled holes.
3.2. Do not over tighten screws.

10
step 4: attach top panel
(H1) x 5
cam
(H5) x 2
wooden dowel
(H4) x 5
cam bolt
4.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush.
4.3. Refer to page 6 for instructions on how to use the cam lock system.
4.4. Do not over tighten bolts.

step 5: attach back panel
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H6) x 27
short pan head screw
5.1. Make sure the screws go through the pre-drilled holes properly.
5.2. Do not over tighten screws.
11
hole for anti-tip
pre-drilled holes

step 6: attach adjustable shelf stretchers to adjustable shelves then install
(H1) x 6
cam
(H5) x 3
wooden dowel
(H4) x 6
cam bolt
(H2) x 12
shelf support
6.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
6.2. Screw-In cam bolts must be screwed down ush.
6.3. Refer to page 6 for instructions on how to use the cam lock system.
6.4. Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
6.5. Angle shelf to t between the rails and set on top of shelf supports.
12
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
Screw-In cam bolts must be screwed down ush.
Refer to page 6 for instructions on how to use the cam lock system.
Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.

step 7: install anti-tip kit
(H3) x 1
wall anchor
(H8) x 1
38mm wall
screw
(H9) x 1
wall strap
(H10) x 1
19mm pan
head screw
(H11) x 2
5/8”washer
Position against wall
Mark position of strap hole on
wall
Drill 1/4’’ hole
Tap in wall anchor
Fasten anti-tip strap
with at-head screw provided
13
(H8)
(H9)
(H11)
(H10)
(H11)
(H3)
Mark position of strap hole on
wall
Fasten anti-tip strap
with at-head screw provided

WARNING
Children have died from furniture tipover.
To reduce the risk
of furniture tipover:
• ALWAYS install tipover restraint provided.
• NEVER put a
TV on this product.
• NEVER allow children to stand, climb or
hang
on drawers, doors, or shelves.
• Place heaviest items
in the lowest drawers.
• NEVER open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
This is a permanent label.
Do notremove!
1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in
excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.
2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
14
65 lbs.
per shelf
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.